lkml.org 
[lkml]   [2013]   [Dec]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] usb: chipidea: msm: Use USB PHY API to control PHY state
On Wed, Dec 04, 2013 at 11:35:54AM +0200, Ivan T. Ivanov wrote:
>
> Hi Peter,
>
> On Wed, 2013-12-04 at 13:37 +0800, Peter Chen wrote:
> > On Mon, Nov 11, 2013 at 04:36:09PM +0200, Ivan T. Ivanov wrote:
> > >
> > > Hi Peter,
> > >
> > > On Mon, 2013-11-11 at 21:59 +0800, Peter Chen wrote:
> > > > On Mon, Nov 11, 2013 at 03:35:37PM +0200, Ivan T. Ivanov wrote:
> > > > > From: "Ivan T. Ivanov" <iivanov@mm-sol.com>
> > > > >
> > > > > PHY drivers keep track of the current state of the hardware,
> > > > > so don't change PHY settings under it.
> > > > >
> > > > > Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
> > > > > ---
> > > > > drivers/usb/chipidea/ci_hdrc_msm.c | 9 ++-------
> > > > > 1 file changed, 2 insertions(+), 7 deletions(-)
> > > > >
> > > > > diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
> > > > > index e9624f3..338b209 100644
> > > > > --- a/drivers/usb/chipidea/ci_hdrc_msm.c
> > > > > +++ b/drivers/usb/chipidea/ci_hdrc_msm.c
> > > > > @@ -20,13 +20,11 @@
> > > > > static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> > > > > {
> > > > > struct device *dev = ci->gadget.dev.parent;
> > > > > - int val;
> > > > >
> > > > > switch (event) {
> > > > > case CI_HDRC_CONTROLLER_RESET_EVENT:
> > > > > dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
> > > > > - writel(0, USB_AHBBURST);
> > > > > - writel(0, USB_AHBMODE);
> > > > > + usb_phy_init(ci->transceiver);
> > > >
> > > > It will reset the PHY, but your comment is "don't change PHY settings under it"
> > >
> > > :-). This function is exported by PHY drivers, so they will know how
> > > to handle this change.
> > >
> > > >
> > > > > break;
> > > > > case CI_HDRC_CONTROLLER_STOPPED_EVENT:
> > > > > dev_dbg(dev, "CI_HDRC_CONTROLLER_STOPPED_EVENT received\n");
> > > > > @@ -34,10 +32,7 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> > > > > * Put the transceiver in non-driving mode. Otherwise host
> > > > > * may not detect soft-disconnection.
> > > > > */
> > > > > - val = usb_phy_io_read(ci->transceiver, ULPI_FUNC_CTRL);
> > > > > - val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
> > > > > - val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
> > > > > - usb_phy_io_write(ci->transceiver, val, ULPI_FUNC_CTRL);
> > > > > + usb_phy_notify_disconnect(ci->transceiver, USB_SPEED_UNKNOWN);
> > > >
> > > > Where you have implemented .notify_disconnect?
> > > > I have not found it at your phy driver.
> > >
> > > Yep, I will post PHY driver changes shortly. Meanwhile this should
> > > not break existing board file based platforms, because not of them
> > > could be compiled (HTC Dream, Halibut Board) and DT based platforms
> > > are sill work in progress.
> > >
> >
> > Hi Ivan, I am going to apply this msm chipidea patchset, but the change
> > in this file is different with its original meaning.
>
> What did you mean?
>
> CI_HDRC_CONTROLLER_RESET_EVENT -> usb_phy_init()
> Take wherever actions are needed to put device in known state. ?

At current code, it only sets two AHB parameters which should be only related
to controller but your patch init the whole PHY, look at msm_otg_reset,
it does many other things, like phy reset, controller reset, etc.

Does the partial otg fsm at msm_otg_sm_work will be called or not? If it is
not called, then, it is OK you just use msm_otg_reset here.

>
> CI_HDRC_CONTROLLER_STOPPED_EVENT -> usb_phy_notify_disconnect()
> Emitted after ci->driver->disconnect(&ci->gadget);

I just see your [PATCH v4 14/15] usb: phy: msm: Handle disconnect events,
then, it is ok now. By the way, do I need to wait your phy patches are queued,
otherwise, it may not work?

>
> Probably I am missing something.
>
>
> > Have you
> > tested at existing platforms?
>
>
> I have 8074 based DragonBoard which I used for testing.
> CV Test Suite engine "Chapter 9 tests" are passing except
> "Halt Endpoint Test".

I mean with your patch, the old non-dt platform can work or not?

--

Best Regards,
Peter Chen



\
 
 \ /
  Last update: 2013-12-04 15:41    [W:0.070 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site