lkml.org 
[lkml]   [2013]   [Dec]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 3/3] mfd: max14577: Add device tree bindings document
Hi Krzysztof,

On 12/04/2013 07:40 PM, Krzysztof Kozlowski wrote:
> Add document describing device tree bindings for MAX14577 MFD driver.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> Documentation/devicetree/bindings/mfd/max14577.txt | 48 ++++++++++++++++++++
> 1 file changed, 48 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/max14577.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt
> new file mode 100644
> index 000000000000..f4fd16360b6b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/max14577.txt
> @@ -0,0 +1,48 @@
> +MAXIM MAX14577 multi-function device
> +
> +MAX14577 is a Multi-function device with Micro-USB Interface Circuit, Li+
> +Battery Charger and SFOUT LDO output for powering USB devices. It is
> +interfaced to host controller using I2C.
> +
> +Required properties:
> +- compatible : Must be "maxim,max14577".
> +- reg : I2C slave address for the max14577 chip.
> +- interrupts : IRQ line for the max14577 chip.
> +- interrupt-parent : The parent interrupt controller.
> +
> +Optional nodes:
> +- regulators :
> + Required child node properties:
> + - compatible : "maxim,max14577-regulator"
> +
> + Optional child nodes:
> + Each child node representing a regulator, following standard regulator
> + bindings. Valid names for a regulator are: "CHARGER" and "SAFEOUT".
> + The SAFEOUT is a constant voltage regulator so there is no need to specify
> + voltages for it.
> +
> + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt
> +
> +Example:
> + max14577@25 {
> + compatible = "maxim,max14577";
> + reg = <0x25>;
> + interrupt-parent = <&gpx1>;
> + interrupts = <5 0>;
> +
> + regulators {
> + compatible = "maxim,max14577-regulator";
> +
> + safeout_reg: safeout@1 {
> + regulator-compatible = "SAFEOUT";
> + regulator-name = "SAFEOUT";
> + };
> + charger_reg: charger@0 {
> + regulator-compatible = "CHARGER";
> + regulator-name = "CHARGER";
> + regulator-min-microamp = <90000>;
> + regulator-max-microamp = <950000>;
> + regulator-boot-on;
> + };
> + };

I prefer to add dt data about max14577-muic on following:
If extcon consumer driver need to use muic device, dts should provide following dt data.

muic: max14577-muic {
compatible = "maxim, max14577-muic";
};
> + };
>

For example,
If fuel-gauge want to use extcon subsystem, dt data of fuel-gauge add 'extcon' property as following:

fuel-gague@ {
compatible = "...";
extcon = <&muic>;
}


Thanks,
Chanwoo Choi









\
 
 \ /
  Last update: 2013-12-04 12:01    [W:0.091 / U:0.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site