lkml.org 
[lkml]   [2013]   [Dec]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] regmap: irq: Allow using zero value for ack_base
Date
In some cases, clear interrupt register may be at address 0.
This patch allows to use such configurations by adding additional
configuration bit to indicate this.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
drivers/base/regmap/regmap-irq.c | 6 +++---
include/linux/regmap.h | 5 ++++-
2 files changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/base/regmap/regmap-irq.c b/drivers/base/regmap/regmap-irq.c
index 763c60d..8269206 100644
--- a/drivers/base/regmap/regmap-irq.c
+++ b/drivers/base/regmap/regmap-irq.c
@@ -113,7 +113,7 @@ static void regmap_irq_sync_unlock(struct irq_data *data)
* OR if there is masked interrupt which hasn't been Acked,
* it'll be ignored in irq handler, then may introduce irq storm
*/
- if (d->mask_buf[i] && d->chip->ack_base) {
+ if (d->mask_buf[i] && (d->chip->ack_base || d->chip->use_ack)) {
reg = d->chip->ack_base +
(i * map->reg_stride * d->irq_reg_stride);
ret = regmap_write(map, reg, d->mask_buf[i]);
@@ -271,7 +271,7 @@ static irqreturn_t regmap_irq_thread(int irq, void *d)
for (i = 0; i < data->chip->num_regs; i++) {
data->status_buf[i] &= ~data->mask_buf[i];

- if (data->status_buf[i] && chip->ack_base) {
+ if (data->status_buf[i] && (chip->ack_base || chip->use_ack)) {
reg = chip->ack_base +
(i * map->reg_stride * data->irq_reg_stride);
ret = regmap_write(map, reg, data->status_buf[i]);
@@ -448,7 +448,7 @@ int regmap_add_irq_chip(struct regmap *map, int irq, int irq_flags,
goto err_alloc;
}

- if (d->status_buf[i] && chip->ack_base) {
+ if (d->status_buf[i] && (chip->ack_base || chip->use_ack)) {
reg = chip->ack_base +
(i * map->reg_stride * d->irq_reg_stride);
ret = regmap_write(map, reg,
diff --git a/include/linux/regmap.h b/include/linux/regmap.h
index e559078..3a36f61 100644
--- a/include/linux/regmap.h
+++ b/include/linux/regmap.h
@@ -497,11 +497,13 @@ struct regmap_irq {
*
* @status_base: Base status register address.
* @mask_base: Base mask register address.
- * @ack_base: Base ack address. If zero then the chip is clear on read.
+ * @ack_base: Base ack address. If zero then the chip is clear on read.
+ * Using zero value is possible with @use_ack bit.
* @wake_base: Base address for wake enables. If zero unsupported.
* @irq_reg_stride: Stride to use for chips where registers are not contiguous.
* @init_ack_masked: Ack all masked interrupts once during initalization.
* @mask_invert: Inverted mask register: cleared bits are masked out.
+ * @use_ack: Use @ack register even it zero.
* @wake_invert: Inverted wake register: cleared bits are wake enabled.
* @runtime_pm: Hold a runtime PM lock on the device when accessing it.
*
@@ -520,6 +522,7 @@ struct regmap_irq_chip {
unsigned int irq_reg_stride;
bool init_ack_masked:1;
bool mask_invert:1;
+ bool use_ack:1;
bool wake_invert:1;
bool runtime_pm:1;

--
1.8.3.2


\
 
 \ /
  Last update: 2013-12-15 11:21    [W:0.176 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site