lkml.org 
[lkml]   [2013]   [Nov]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
SubjectRe: [PATCH RFC 1/4] phy: Add new Exynos5 USB 3.0 PHY driver
From
Hi Kishon,



On Mon, Nov 4, 2013 at 6:42 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
> Hi,
>
>
> On Monday 04 November 2013 03:45 PM, Kamil Debski wrote:
>>
>> Hi Kishon,
>>
>>> From: Kishon Vijay Abraham I [mailto:kishon@ti.com]
>>> Sent: Monday, November 04, 2013 7:55 AM
>>>
>>> Hi Vivek,
>>>
>>> On Thursday 31 October 2013 01:15 PM, Vivek Gautam wrote:
>>>>
>>>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>>>> The new driver uses the generic PHY framework and will interact with
>>>> DWC3 controller present on Exynos5 series of SoCs.
>>>
>>>
>>> In Exynos, you have a single IP that supports both USB3 and USB2 PHY
>>> right? I think that needs to be mentioned here.
>>
>>
>> As far as I know the IP is different.
>
>
> Ok. Sometime back Vivek was mentioning about a single IP for both USB3 and
> USB2. Thought it should be this driver. Anyway thanks for the clarification.

Right Kishon, I had mentioned that Exynos5's dwc3 controller have a
single IP for USB2 and USB3 phy.
From what i see, on exynos5 systems the dwc3 controller uses a combo
of usb 2 (utmi+) and usb 3 (pipe 3) phy
(with base address starting 0x12100000).

Kamil, Tomasz,

Please correct me if i am wrong.

>
> Cheers
> Kishon
>
>>
>>> Do you have separate registers that should be used for
>>> initializing/powerin_on/powering_off etc.. for usb2 phy and usb3 phy?
>>> If so, then you should model this driver as a single driver that
>>> supports two PHYs similar to what Sylwester has done before?
>>
>>
>> Best wishes,
>> Kamil
>>
>>> Cheers
>>> Kishon
>>>
>>>>
>>>> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
>>>> ---
>>>> .../devicetree/bindings/phy/samsung-phy.txt | 20 +
>>>> drivers/phy/Kconfig | 7 +
>>>> drivers/phy/Makefile | 1 +
>>>> drivers/phy/phy-exynos5-usb3.c | 562
>>>
>>> ++++++++++++++++++++
>>>>
>>>> 4 files changed, 590 insertions(+), 0 deletions(-)
>>>> create mode 100644 drivers/phy/phy-exynos5-usb3.c
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>>> b/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>>> index c0fccaa..9b5c111 100644
>>>> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>>> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>>> @@ -20,3 +20,23 @@ Required properties:
>>>> - compatible : should be "samsung,exynos5250-dp-video-phy";
>>>> - reg : offset and length of the Display Port PHY register set;
>>>> - #phy-cells : from the generic PHY bindings, must be 0;
>>>> +
>>>> +Samsung Exynos5 SoC seiries USB 3.0 PHY controller
>>>> +--------------------------------------------------
>>>> +
>>>> +Required properties:
>>>> +- compatible :
>>>> + should be "samsung,exynos5250-usb3phy" for exynos5250 SoC
>>>> + should be "samsung,exynos5420-usb3phy" for exynos5420 SoC
>>>> +- reg : Register offset and length array
>>>> + - first field corresponds to USB 3.0 PHY register set;
>>>> + - second field corresponds to PHY power isolation register
>>>> + present in PMU;
>>>> +- clocks: Clock IDs array as required by the controller
>>>> +- clock-names: names of clocks correseponding to IDs in the clock
>>>
>>> property;
>>>>
>>>> + Required clocks:
>>>> + - first clock is main PHY clock (same as USB 3.0 controller IP
>>>
>>> clock)
>>>>
>>>> + - second clock is reference clock (usually crystal clock)
>>>> + optional clock:
>>>> + - third clock is special clock used by PHY for operation
>>>> +- #phy-cells : from the generic PHY bindings, must be 0;
>>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index
>>>> a344f3d..9a100c6 100644
>>>> --- a/drivers/phy/Kconfig
>>>> +++ b/drivers/phy/Kconfig
>>>> @@ -51,4 +51,11 @@ config PHY_EXYNOS_DP_VIDEO
>>>> help
>>>> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>>>>
>>>> +config PHY_EXYNOS5_USB3
>>>> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
>>>> + depends on ARCH_EXYNOS5
>>>> + select GENERIC_PHY
>>>> + help
>>>> + Enable USB 3.0 PHY support for Exynos 5 SoC series
>>>> +
>>>> endmenu
>>>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index
>>>> d0caae9..9c06a61 100644
>>>> --- a/drivers/phy/Makefile
>>>> +++ b/drivers/phy/Makefile
>>>> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) +=
>>>> phy-exynos-dp-
>>>
>>> video.o
>>>>
>>>> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
>>>> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
>>>> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
>>>> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
>>>> diff --git a/drivers/phy/phy-exynos5-usb3.c
>>>> b/drivers/phy/phy-exynos5-usb3.c new file mode 100644 index
>>>> 0000000..b9a2674
>>>> --- /dev/null
>>>> +++ b/drivers/phy/phy-exynos5-usb3.c
>>>> @@ -0,0 +1,562 @@
>>>> +/*
>>>> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
>>>> + *
>>>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>>>> + * Author: Vivek Gautam <gautam.vivek@samsung.com>
>>>> + *
>>>> + * This program is free software; you can redistribute it and/or
>>>> +modify
>>>> + * it under the terms of the GNU General Public License version 2 as
>>>> + * published by the Free Software Foundation.
>>>> + */
>>>> +
>>>> +#include <linux/clk.h>
>>>> +#include <linux/delay.h>
>>>> +#include <linux/io.h>
>>>> +#include <linux/kernel.h>
>>>> +#include <linux/module.h>
>>>> +#include <linux/of.h>
>>>> +#include <linux/of_address.h>
>>>> +#include <linux/phy/phy.h>
>>>> +#include <linux/platform_device.h>
>>>> +#include <linux/mutex.h>
>>>> +
>>>> +/* Exynos USB PHY registers */
>>>> +#define EXYNOS5_FSEL_9MHZ6 0x0
>>>> +#define EXYNOS5_FSEL_10MHZ 0x1
>>>> +#define EXYNOS5_FSEL_12MHZ 0x2
>>>> +#define EXYNOS5_FSEL_19MHZ2 0x3
>>>> +#define EXYNOS5_FSEL_20MHZ 0x4
>>>> +#define EXYNOS5_FSEL_24MHZ 0x5
>>>> +#define EXYNOS5_FSEL_50MHZ 0x7
>>>> +
>>>> +/* EXYNOS5: USB 3.0 DRD PHY registers */
>>>> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
>>>> +
>>>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>>>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>>>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYUTMI (0x08)
>>>> +
>>>> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
>>>> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
>>>> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
>>>> +
>>>> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
>>>> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
>>>> +
>>>> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
>>>> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
>>>> +
>>>> +#define PHYCLKRST_SSC_EN (0x1 << 20)
>>>> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
>>>> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
>>>> +
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
>>>> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
>>>> +
>>>> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
>>>> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
>>>> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
>>>> +
>>>> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
>>>> +
>>>> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
>>>> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
>>>> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
>>>> +
>>>> +#define PHYCLKRST_PORTRESET (0x1 << 1)
>>>> +#define PHYCLKRST_COMMONONN (0x1 << 0)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYREG0 (0x14)
>>>> +#define EXYNOS5_DRD_PHYREG1 (0x18)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
>>>> +
>>>> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
>>>> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
>>>> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
>>>> +
>>>> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
>>>> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYTERM (0x24)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYTEST (0x28)
>>>> +
>>>> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
>>>> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYADP (0x2c)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
>>>> +
>>>> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
>>>> +
>>>> +#define EXYNOS5_DRD_PHYRESUME (0x34)
>>>> +#define EXYNOS5_DRD_LINKPORT (0x44)
>>>> +
>>>> +
>>>> +/* Isolation, configured in the power management unit */
>>>> +#define EXYNOS5_USB_ISOL_DRD (1 << 0)
>>>> +
>>>> +#define CLKSEL_ERROR -1
>>>> +
>>>> +#ifndef KHZ
>>>> +#define KHZ 1000
>>>> +#endif
>>>> +
>>>> +#ifndef MHZ
>>>> +#define MHZ (KHZ * KHZ)
>>>> +#endif
>>>> +
>>>> +enum samsung_cpu_type {
>>>> + TYPE_EXYNOS5250,
>>>> + TYPE_EXYNOS5420,
>>>> +};
>>>> +
>>>> +enum usb3phy_state {
>>>> + STATE_OFF,
>>>> + STATE_ON,
>>>> +};
>>>> +
>>>> +struct usb3phy_config {
>>>> + enum samsung_cpu_type cpu;
>>>> + bool has_sclk_usbphy30;
>>>> +};
>>>> +
>>>> +struct usb3phy_instance {
>>>> + char *label;
>>>> + struct usb3phy_driver *drv;
>>>> + struct phy *phy;
>>>> + enum usb3phy_state state;
>>>> + u32 clk;
>>>> + unsigned long rate;
>>>> +};
>>>> +
>>>> +struct usb3phy_driver {
>>>> + struct device *dev;
>>>> + void __iomem *reg_phy;
>>>> + void __iomem *reg_isol;
>>>> + struct clk *clk;
>>>> + struct clk *sclk_usbphy30;
>>>> + struct usb3phy_instance instance;
>>>> +};
>>>> +
>>>> +/*
>>>> + * exynos5_rate_to_clk() converts the supplied clock rate to the
>>>> +value that
>>>> + * can be written to the phy register.
>>>> + */
>>>> +static u32 exynos5_rate_to_clk(unsigned long rate) {
>>>> + unsigned int clksel;
>>>> +
>>>> + /* EXYNOS5_FSEL_MASK */
>>>> +
>>>> + switch (rate) {
>>>> + case 9600 * KHZ:
>>>> + clksel = EXYNOS5_FSEL_9MHZ6;
>>>> + break;
>>>> + case 10 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_10MHZ;
>>>> + break;
>>>> + case 12 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_12MHZ;
>>>> + break;
>>>> + case 19200 * KHZ:
>>>> + clksel = EXYNOS5_FSEL_19MHZ2;
>>>> + break;
>>>> + case 20 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_20MHZ;
>>>> + break;
>>>> + case 24 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_24MHZ;
>>>> + break;
>>>> + case 50 * MHZ:
>>>> + clksel = EXYNOS5_FSEL_50MHZ;
>>>> + break;
>>>> + default:
>>>> + clksel = CLKSEL_ERROR;
>>>> + }
>>>> +
>>>> + return clksel;
>>>> +}
>>>> +
>>>> +static void exynos5_usb3phy_isol(struct usb3phy_instance *inst, bool
>>>> +on) {
>>>> + struct usb3phy_driver *drv = inst->drv;
>>>> + u32 tmp;
>>>> +
>>>> + if (!drv->reg_isol)
>>>> + return;
>>>> +
>>>> + tmp = readl(drv->reg_isol);
>>>> + if (on)
>>>> + tmp &= ~EXYNOS5_USB_ISOL_DRD;
>>>> + else
>>>> + tmp |= EXYNOS5_USB_ISOL_DRD;
>>>> + writel(tmp, drv->reg_isol);
>>>> +}
>>>> +
>>>> +/*
>>>> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from
>>> clock core.
>>>>
>>>> + */
>>>> +static u32 exynos5_usb3phy_set_refclk(struct usb3phy_instance *inst)
>>>> +{
>>>> + u32 reg;
>>>> + u32 refclk;
>>>> +
>>>> + refclk = inst->clk;
>>>> +
>>>> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
>>>> + PHYCLKRST_FSEL(refclk);
>>>> +
>>>> + switch (refclk) {
>>>> + case EXYNOS5_FSEL_50MHZ:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>>>> + break;
>>>> + case EXYNOS5_FSEL_20MHZ:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>>>> + break;
>>>> + case EXYNOS5_FSEL_19MHZ2:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>>>> + break;
>>>> + case EXYNOS5_FSEL_24MHZ:
>>>> + default:
>>>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
>>>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>>>> + break;
>>>> + }
>>>> +
>>>> + return reg;
>>>> +}
>>>> +
>>>> +static void exynos5_usb3phy_init(struct usb3phy_instance *inst) {
>>>> + struct usb3phy_driver *drv = inst->drv;
>>>> + u32 phyparam0;
>>>> + u32 phyparam1;
>>>> + u32 linksystem;
>>>> + u32 phybatchg;
>>>> + u32 phytest;
>>>> + u32 phyclkrst;
>>>> +
>>>> + /* Reset USB 3.0 PHY */
>>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
>>>> +
>>>> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>>>> + /* Select PHY CLK source */
>>>> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
>>>> + /* Set Loss-of-Signal Detector sensitivity */
>>>> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
>>>> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
>>>> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>>>> +
>>>> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
>>>> +
>>>> + /*
>>>> + * Setting the Frame length Adj value[6:1] to default 0x20
>>>> + * See xHCI 1.0 spec, 5.2.4
>>>> + */
>>>> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
>>>> + LINKSYSTEM_FLADJ(0x20);
>>>> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
>>>> +
>>>> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>>>> + /* Set Tx De-Emphasis level */
>>>> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>>>> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
>>>> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>>>> +
>>>> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>>>> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
>>>> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
>>>> +
>>>> + /* PHYTEST POWERDOWN Control */
>>>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>>> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
>>>> + PHYTEST_POWERDOWN_HSP);
>>>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>>> +
>>>> + /* UTMI Power Control */
>>>> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>>>> +
>>>> + phyclkrst = exynos5_usb3phy_set_refclk(inst);
>>>> +
>>>> + phyclkrst |= PHYCLKRST_PORTRESET |
>>>> + /* Digital power supply in normal operating mode */
>>>> + PHYCLKRST_RETENABLEN |
>>>> + /* Enable ref clock for SS function */
>>>> + PHYCLKRST_REF_SSP_EN |
>>>> + /* Enable spread spectrum */
>>>> + PHYCLKRST_SSC_EN |
>>>> + /* Power down HS Bias and PLL blocks in suspend
>>>> mode
>>>
>>> */
>>>>
>>>> + PHYCLKRST_COMMONONN;
>>>> +
>>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>>> +
>>>> + udelay(10);
>>>> +
>>>> + phyclkrst &= ~PHYCLKRST_PORTRESET;
>>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>>> +
>>>> +}
>>>> +
>>>> +static void exynos5_usb3phy_exit(struct usb3phy_instance *inst) {
>>>> + struct usb3phy_driver *drv = inst->drv;
>>>> + u32 phyutmi;
>>>> + u32 phyclkrst;
>>>> + u32 phytest;
>>>> +
>>>> + phyutmi = PHYUTMI_OTGDISABLE |
>>>> + PHYUTMI_FORCESUSPEND |
>>>> + PHYUTMI_FORCESLEEP;
>>>> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
>>>> +
>>>> + /* Resetting the PHYCLKRST enable bits to reduce leakage current
>>>
>>> */
>>>>
>>>> + phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>>> + phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
>>>> + PHYCLKRST_SSC_EN |
>>>> + PHYCLKRST_COMMONONN);
>>>> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>>>> +
>>>> + /* Control PHYTEST to remove leakage current */
>>>> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
>>>> + phytest |= PHYTEST_POWERDOWN_SSP |
>>>> + PHYTEST_POWERDOWN_HSP;
>>>> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST); }
>>>> +
>>>> +static int exynos5_usb3phy_power_on(struct phy *phy) {
>>>> + struct usb3phy_instance *inst = phy_get_drvdata(phy);
>>>> + struct usb3phy_driver *drv = inst->drv;
>>>> + int ret;
>>>> +
>>>> + dev_info(drv->dev, "Request to power_on \"%s\" usb phy\n",
>>>> + inst->label);
>>>> +
>>>> + if (drv->sclk_usbphy30)
>>>> + clk_prepare_enable(drv->sclk_usbphy30);
>>>> +
>>>> + ret = clk_prepare_enable(drv->clk);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + if (inst->state == STATE_ON) {
>>>> + dev_err(drv->dev, "usb phy \"%s\" already on",
>>>> + inst->label);
>>>> + ret = -ENODEV;
>>>> + goto err0;
>>>> + }
>>>> +
>>>> + inst->state = STATE_ON;
>>>> +
>>>> + /* Initialize the PHY and power it ON */
>>>> + exynos5_usb3phy_init(inst);
>>>> + exynos5_usb3phy_isol(inst, 0);
>>>> +
>>>> +err0:
>>>> + clk_disable_unprepare(drv->clk);
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> +static int exynos5_usb3phy_power_off(struct phy *phy) {
>>>> + struct usb3phy_instance *inst = phy_get_drvdata(phy);
>>>> + struct usb3phy_driver *drv = inst->drv;
>>>> + int ret;
>>>> +
>>>> + dev_info(drv->dev, "Request to power_off \"%s\" usb phy\n",
>>>> + inst->label);
>>>> + ret = clk_prepare_enable(drv->clk);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + if (inst->state == STATE_OFF) {
>>>> + dev_err(drv->dev, "usb phy \"%s\" already off",
>>>> + inst->label);
>>>> + ret = -ENODEV;
>>>> + goto err0;
>>>> + }
>>>> +
>>>> + inst->state = STATE_OFF;
>>>> +
>>>> + /* Power-off the PHY and de-initialize it */
>>>> + exynos5_usb3phy_isol(inst, 1);
>>>> + exynos5_usb3phy_exit(inst);
>>>> +
>>>> +err0:
>>>> + clk_disable_unprepare(drv->clk);
>>>> + if (drv->sclk_usbphy30)
>>>> + clk_disable_unprepare(drv->sclk_usbphy30);
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> +static struct phy_ops exynos5_usb3phy_ops = {
>>>> + .power_on = exynos5_usb3phy_power_on,
>>>> + .power_off = exynos5_usb3phy_power_off,
>>>> + .owner = THIS_MODULE,
>>>> +};
>>>> +
>>>> +static const struct of_device_id exynos5_usb3phy_of_match[];
>>>> +
>>>> +static int exynos5_usb3phy_probe(struct platform_device *pdev) {
>>>> + struct device *dev = &pdev->dev;
>>>> + struct usb3phy_driver *drv;
>>>> + struct usb3phy_instance *inst;
>>>> + struct phy_provider *phy_provider;
>>>> + struct resource *res;
>>>> + struct clk *clk;
>>>> + const struct of_device_id *match;
>>>> + const struct usb3phy_config *cfg;
>>>> +
>>>> + match = of_match_node(exynos5_usb3phy_of_match, pdev-
>>>> dev.of_node);
>>>> + if (!match) {
>>>> + dev_err(dev, "of_match_node() failed\n");
>>>> + return -EINVAL;
>>>> + }
>>>> + cfg = match->data;
>>>> + if (!cfg) {
>>>> + dev_err(dev, "Failed to get configuration\n");
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + drv = devm_kzalloc(dev, sizeof(struct usb3phy_driver),
>>>
>>> GFP_KERNEL);
>>>>
>>>> + if (!drv) {
>>>> + dev_err(dev, "Failed to allocate memory\n");
>>>> + return -ENOMEM;
>>>> + }
>>>> +
>>>> + dev_set_drvdata(dev, drv);
>>>> + drv->dev = dev;
>>>> +
>>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>>> + drv->reg_phy = devm_ioremap_resource(dev, res);
>>>> + if (IS_ERR(drv->reg_phy)) {
>>>> + dev_err(dev, "Failed to map register memory (phy)\n");
>>>> + return PTR_ERR(drv->reg_phy);
>>>> + }
>>>> +
>>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>>>> + drv->reg_isol = devm_ioremap_resource(dev, res);
>>>> + if (IS_ERR(drv->reg_isol)) {
>>>> + dev_err(dev, "Failed to map register memory
>>>> (isolation)\n");
>>>> + return PTR_ERR(drv->reg_isol);
>>>> + }
>>>> +
>>>> + phy_provider = devm_of_phy_provider_register(dev,
>>>
>>> of_phy_simple_xlate);
>>>>
>>>> + if (IS_ERR(phy_provider)) {
>>>> + dev_err(drv->dev, "Failed to register phy provider\n");
>>>> + return PTR_ERR(phy_provider);
>>>> + }
>>>> +
>>>> + drv->clk = devm_clk_get(dev, "phy");
>>>> + if (IS_ERR(drv->clk)) {
>>>> + dev_err(dev, "Failed to get clock of phy controller\n");
>>>> + return PTR_ERR(drv->clk);
>>>> + }
>>>> +
>>>> + /*
>>>> + * Exysno5420 SoC has an additional special clock, used for
>>>> + * for USB 3.0 PHY operation, this clock goes to the PHY block
>>>> + * as a reference clock to clock generation block of the
>>>
>>> controller.
>>>>
>>>> + */
>>>> + if (cfg->has_sclk_usbphy30) {
>>>> + drv->sclk_usbphy30 = devm_clk_get(dev, "sclk_usbphy30");
>>>> + if (IS_ERR(drv->clk)) {
>>>> + dev_err(dev, "Failed to get phy reference
>>>> clock\n");
>>>> + return PTR_ERR(drv->clk);
>>>> + }
>>>> + }
>>>> +
>>>> + inst = &drv->instance;
>>>> + inst->drv = drv;
>>>> + inst->label = "usb3drd";
>>>> +
>>>> + dev_info(dev, "Creating phy \"%s\"\n", inst->label);
>>>> + inst->phy = devm_phy_create(dev, &exynos5_usb3phy_ops, NULL);
>>>> + if (IS_ERR(inst->phy)) {
>>>> + dev_err(drv->dev, "Failed to create usb3phy \"%s\"\n",
>>>> + inst->label);
>>>> + return PTR_ERR(inst->phy);
>>>> + }
>>>> +
>>>> + phy_set_drvdata(inst->phy, inst);
>>>> +
>>>> + clk = clk_get(dev, inst->label);
>>>> + if (IS_ERR(clk)) {
>>>> + dev_err(dev, "Failed to get clock of \"%s\" phy\n",
>>>> + inst->label);
>>>> + return PTR_ERR(clk);
>>>> + }
>>>> +
>>>> + inst->rate = clk_get_rate(clk);
>>>> +
>>>> + inst->clk = exynos5_rate_to_clk(inst->rate);
>>>> + if (inst->clk == CLKSEL_ERROR) {
>>>> + dev_err(dev, "Clock rate (%ld) not supported\n",
>>>> + inst->rate);
>>>> + clk_put(clk);
>>>> + return -EINVAL;
>>>> + }
>>>> + clk_put(clk);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +const struct usb3phy_config exynos5420_usb3phy_cfg = {
>>>> + .cpu = TYPE_EXYNOS5420,
>>>> + .has_sclk_usbphy30 = true,
>>>> +};
>>>> +
>>>> +const struct usb3phy_config exynos5250_usb3phy_cfg = {
>>>> + .cpu = TYPE_EXYNOS5250,
>>>> + .has_sclk_usbphy30 = false,
>>>> +};
>>>> +
>>>> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
>>>> + {
>>>> + .compatible = "samsung,exynos5250-usb3phy",
>>>> + .data = &exynos5250_usb3phy_cfg
>>>> + }, {
>>>> + .compatible = "samsung,exynos5420-usb3phy",
>>>> + .data = &exynos5420_usb3phy_cfg
>>>> + },
>>>> + { },
>>>> +};
>>>> +
>>>> +static struct platform_driver exynos5_usb3phy_driver = {
>>>> + .probe = exynos5_usb3phy_probe,
>>>> + .driver = {
>>>> + .of_match_table = exynos5_usb3phy_of_match,
>>>> + .name = "exynos5-usb3phy",
>>>> + .owner = THIS_MODULE,
>>>> + }
>>>> +};
>>>> +
>>>> +module_platform_driver(exynos5_usb3phy_driver);
>>>> +MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
>>>> +MODULE_AUTHOR("Vivek Gautam <gautam.vivek@samsung.com>");
>>>> +MODULE_LICENSE("GPL v2"); MODULE_ALIAS("platform:exynos5-usb3phy");
>>>>
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
>
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html



--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India


\
 
 \ /
  Last update: 2013-11-05 08:41    [W:0.123 / U:0.896 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site