lkml.org 
[lkml]   [2013]   [Nov]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] memory: ti-aemif: add bindings for AEMIF driver
From
Date

On Nov 20, 2013, at 1:03 PM, ivan.khoronzhuk <ivan.khoronzhuk@ti.com> wrote:

> On 11/20/2013 08:21 PM, Jean-Christophe PLAGNIOL-VILLARD wrote:
>>> + the chip select signal.
>>> + Minimum value is 1 (0 treated as 1).
>>> +
>>> +- ti,cs-wsetup: write setup width, ns
>>> + Time between the beginning of a memory cycle
>>> + and the activation of write strobe.
>>> + Minimum value is 1 (0 treated as 1).
>>> +
>>> +- ti,cs-wstrobe: write strobe width, ns
>>> + Time between the activation and deactivation of
>>> + the write strobe.
>>> + Minimum value is 1 (0 treated as 1).
>>> +
>>> +- ti,cs-whold: write hold width, ns
>>> + Time between the deactivation of the write
>>> + strobe and the end of the cycle (which may be
>>> + either an address change or the deactivation of
>>> + the chip select signal.
>>> + Minimum value is 1 (0 treated as 1).
>>> +
>>> +If any of the above parameters are absent, current parameter value will be taken
>>> +from the corresponding HW reg.
>>> +
>>> +The name for cs node must be in format csN, where N is the cs number.
>>
>> this is wired we should use reg instead to represent the cs as done for SPI
>> or a an other property
>>
>> Best Regards,
>> J.
>>
>
> Ok, I will add new property cs-chipselect like following :
>
> ti,cs-chipselect: number of chipselect. Indicates on the
> aemif driver which chipselect is used
> for accessing the memory.
> For compatibles "ti,davinci-aemif" and
> "ti,keystone-aemif" it can be in range [0-3].
> For compatible "ti,omap-L138-aemif" range is [2-5].
>
> Is it OK?

Why do you need this? As it was mentioned just use reg:

So you’d have something like:

memory-controller@21000A00 {

nand:cs2@2 {
reg = <2 0 0>;
ranges;
...

}:
};

However, I’m confused by the example in which you have:

+ nand@0,0x8000000 {
+ compatible = "ti,davinci-nand";
+ reg = <0 0x8000000 0x4000000
+ 1 0x0000000 0x0000100>;
+
+ .. see davinci-nand.txt
+ };

What chipselects is this on 0 & 1?

- k

>
> --
> Regards,
> Ivan Khoronzhuk
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2013-11-22 22:21    [W:0.174 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site