Messages in this thread Patch in this message | | | From | Charles Keepax <> | Subject | [PATCH v2 2/2] regulator: arizona-micsupp: Correct wm5110 voltage selection | Date | Fri, 15 Nov 2013 13:48:23 +0000 |
| |
wm5110 provides different voltage configurations than the other Arizona parts, this patch adds support for this into the regulator driver. Also fixup the default for the configuration register for wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> --- drivers/regulator/arizona-micsupp.c | 54 +++++++++++++++++++++++++++++++++- 1 files changed, 52 insertions(+), 2 deletions(-)
diff --git a/drivers/regulator/arizona-micsupp.c b/drivers/regulator/arizona-micsupp.c index 3c75bf8..034ece7 100644 --- a/drivers/regulator/arizona-micsupp.c +++ b/drivers/regulator/arizona-micsupp.c @@ -144,6 +144,33 @@ static const struct regulator_desc arizona_micsupp = { .owner = THIS_MODULE, }; +static const struct regulator_linear_range arizona_micsupp_ext_ranges[] = { + REGULATOR_LINEAR_RANGE(900000, 0, 0x14, 25000), + REGULATOR_LINEAR_RANGE(1500000, 0x15, 0x27, 100000), +}; + +static const struct regulator_desc arizona_micsupp_ext = { + .name = "MICVDD", + .supply_name = "CPVDD", + .type = REGULATOR_VOLTAGE, + .n_voltages = 40, + .ops = &arizona_micsupp_ops, + + .vsel_reg = ARIZONA_LDO2_CONTROL_1, + .vsel_mask = ARIZONA_LDO2_VSEL_MASK, + .enable_reg = ARIZONA_MIC_CHARGE_PUMP_1, + .enable_mask = ARIZONA_CPMIC_ENA, + .bypass_reg = ARIZONA_MIC_CHARGE_PUMP_1, + .bypass_mask = ARIZONA_CPMIC_BYPASS, + + .linear_ranges = arizona_micsupp_ext_ranges, + .n_linear_ranges = ARRAY_SIZE(arizona_micsupp_ext_ranges), + + .enable_time = 3000, + + .owner = THIS_MODULE, +}; + static const struct regulator_init_data arizona_micsupp_default = { .constraints = { .valid_ops_mask = REGULATOR_CHANGE_STATUS | @@ -156,9 +183,22 @@ static const struct regulator_init_data arizona_micsupp_default = { .num_consumer_supplies = 1, }; +static const struct regulator_init_data arizona_micsupp_ext_default = { + .constraints = { + .valid_ops_mask = REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_BYPASS, + .min_uV = 900000, + .max_uV = 3300000, + }, + + .num_consumer_supplies = 1, +}; + static int arizona_micsupp_probe(struct platform_device *pdev) { struct arizona *arizona = dev_get_drvdata(pdev->dev.parent); + const struct regulator_desc *desc; struct regulator_config config = { }; struct arizona_micsupp *micsupp; int ret; @@ -177,7 +217,17 @@ static int arizona_micsupp_probe(struct platform_device *pdev) * default init_data for it. This will be overridden with * platform data if provided. */ - micsupp->init_data = arizona_micsupp_default; + switch (arizona->type) { + case WM5110: + desc = &arizona_micsupp_ext; + micsupp->init_data = arizona_micsupp_ext_default; + break; + default: + desc = &arizona_micsupp; + micsupp->init_data = arizona_micsupp_default; + break; + } + micsupp->init_data.consumer_supplies = &micsupp->supply; micsupp->supply.supply = "MICVDD"; micsupp->supply.dev_name = dev_name(arizona->dev); @@ -196,7 +246,7 @@ static int arizona_micsupp_probe(struct platform_device *pdev) ARIZONA_CPMIC_BYPASS, 0); micsupp->regulator = devm_regulator_register(&pdev->dev, - &arizona_micsupp, + desc, &config); if (IS_ERR(micsupp->regulator)) { ret = PTR_ERR(micsupp->regulator); -- 1.7.2.5
| |