lkml.org 
[lkml]   [2013]   [Nov]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH] hwmon: (max6650) Add support for gpiodef
From
On Thu, Nov 14, 2013 at 6:18 PM, Guenter Roeck <linux@roeck-us.net> wrote:
> On Thu, Nov 14, 2013 at 06:13:45PM +0000, Laszlo Papp wrote:
>> On Thu, Nov 14, 2013 at 5:24 PM, Guenter Roeck <linux@roeck-us.net> wrote:
>>
>> > On Thu, Nov 14, 2013 at 02:51:01PM +0000, Laszlo Papp wrote:
>> > > It is necessary for end users when they are using the gpio pins
>> > connected to the
>> > > fan controller. There is a separate gpiodef register provided, but it is
>> > unused
>> > > under the usual circumstances and that is probably the reason why this
>> > feature
>> > > has not been added before. It is necessary for our board to function
>> > properly.
>> > >
>> > > Signed-off-by: Laszlo Papp <lpapp@kde.org>
>> > > ---
>> > > Documentation/hwmon/max6650 | 5 +++
>> > > drivers/hwmon/max6650.c | 107
>> > ++++++++++++++++++++++++++++++++++++++++++++
>> > > 2 files changed, 112 insertions(+)
>> > >
>> > > diff --git a/Documentation/hwmon/max6650 b/Documentation/hwmon/max6650
>> > > index 58d9644..32c69a8 100644
>> > > --- a/Documentation/hwmon/max6650
>> > > +++ b/Documentation/hwmon/max6650
>> > > @@ -39,6 +39,11 @@ pwm1 rw relative speed (0-255),
>> > 255=max. speed.
>> > > fan1_div rw sets the speed range the inputs can handle. Legal
>> > > values are 1, 2, 4, and 8. Use lower values for
>> > > faster fans.
>> > > +gpio0 rw sets the gpio 0 PIN. Legal values are 0, 1, 2, and
>> > 3.
>> > > +gpio1 rw sets the gpio 1 PIN. Legal values are 0, 1, 2, and
>> > 3.
>> > > +gpio2 rw sets the gpio 2 PIN. Legal values are 0, 1, 2, and
>> > 3.
>> > > +gpio3 rw sets the gpio 3 PIN. Legal values are 0, and 1.
>> > > +gpio4 rw sets the gpio 4 PIN. Legal values are 0, and 1.
>> > >
>> > gpio pins should be exported through the gpio subsystem, usually with a
>> > gpio
>> > driver. In this case, it may be acceptable to have the driver register with
>> > the gpio subsystem to export the pins. Using local sysfs attributes is
>> > wrong
>> > and unacceptable.
>> >
>>
>> In short: I am not sure.
>>
>> My concern is that these are not generic gpio pins. They seem to have chip
>> specific functionality, like alarm, full-on, and clock (internal and
>> external). Strictly speaking, one could even mention that to expose the
>> GPIODEF register as is without splitting it into five separate gpio pin
>> entries. Even those five pins behave slightly differently.
>>
>> I considered both, but these are the reasons why I decided to keep it chip
>> specific rather than separately in a generic subsystem.
>>
> If the registers are not really gpio pins but are needed / used for chip
> configuration, the other option would be to configure the values using platform
> data and/or devicetree data. Either case, exporting the pins to user space via
> sysfs attribute files in the device directory is the wrong approach.

Hmm, that would not allow dynamic settings on its own - if I am not
mistaken - which we are in need of. I might be mistaken tough, so
please forgive my shortcomings.

I was also thinking of module parameters before, as well. Perhaps that
is a better approach. I am not sure. What do you think about it?


\
 
 \ /
  Last update: 2013-11-14 20:21    [W:0.078 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site