lkml.org 
[lkml]   [2013]   [Nov]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] clk: add specified-rate clock
Date
Hi James, Mike,

On Wednesday 13 of November 2013 14:09:56 James Hogan wrote:
> On 29/05/13 18:39, Mike Turquette wrote:
> > Quoting James Hogan (2013-05-10 05:44:22)
> >> The frequency of some SoC's external oscillators (for example TZ1090's
> >> XTAL1) are configured by the board using pull-ups/pull-downs of
> >> configuration pins, the logic values of which are automatically latched
> >> on reset and available in an SoC register. Add a generic clock component
> >> and DT bindings to handle this.
> >>
> >> It behaves similar to a fixed rate clock (read-only), except it needs
> >> information about a register field (reg, shift, width), and the
> >> clock-frequency is a mapping from register field values to clock
> >> frequencies.
> >>
> >
> > James,
> >
> > Thanks for sending this! It looks mostly good and is a useful clock
> > type to support. Comments below.
>
> Hi Mike,
>
> Sorry for slight delay getting back to you. I had another think about
> this stuff yesterday...
>

Just a random idea that came to my mind while reading this thread:

What about modelling this as a set of fixed rate clocks fed into
a read-only mux?

Best regards,
Tomasz

> >
> > <snip>
> >> diff --git a/Documentation/devicetree/bindings/clock/specified-clock.txt b/Documentation/devicetree/bindings/clock/specified-clock.txt
> >> new file mode 100644
> >> index 0000000..b36ccf9
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/clock/specified-clock.txt
> >> @@ -0,0 +1,39 @@
> >> +Binding for fixed-rate clock sources with readable configuration.
> >> +
> >> +This binding uses the common clock binding[1].
> >> +
> >> +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
> >> +
> >> +Required properties:
> >> +- compatible : Shall be "specified-clock".
> >> +- #clock-cells : From common clock binding; shall be set to 0.
> >> +- reg : Address of configuration register.
> >> +- shift : Shift of config value field in configuration register.
> >> +- width : Width of config value field in configuration register.
> >
> > It might be better to make this a mask instead of the width. We have
> > already hit this issue with the mux table on Nvidia where arbitrary
> > masks are necessary. Mask + shift probably helps future-proof us a bit.
>
> Yes, thanks. I've now borrowed the bit-mask and bit-shift from your mux
> binding proposals (including defaulting shift to ffs(mask)-1 ... nice).
>
> >
> > The rest of the binding looks good.
> >
> > <snip>
> >> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> >> index e7f7fe9..1343179 100644
> >> --- a/drivers/clk/Makefile
> >> +++ b/drivers/clk/Makefile
> >> @@ -8,6 +8,7 @@ obj-$(CONFIG_COMMON_CLK) += clk-fixed-rate.o
> >> obj-$(CONFIG_COMMON_CLK) += clk-gate.o
> >> obj-$(CONFIG_COMMON_CLK) += clk-mux.o
> >> obj-$(CONFIG_COMMON_CLK) += clk-composite.o
> >> +obj-$(CONFIG_COMMON_CLK) += clk-specified-rate.o
> >
> > One thing that does occur to me is that this could potentially be
> > combined with the fixed-rate clock. If the properties for a specified
> > rate existing in the DT data then this code applies, otherwise the
> > existing fixed-rate code is used. I don't have a strong opinion about
> > combining the code, but something to consider.
>
> That's actually a much neater solution. Because the clock is still
> fixed, the register value can be read once while processing the DT node,
> and an otherwise normal fixed rate clock created at the right frequency.
> It doesn't even need to allocate memory to store the table.
>
> The remaining question is whether to extend the fixed-clock binding or
> have a separate one. I'm in two minds. On the one hand it is a
> fixed-rate clock, on the other hand the only shared properties at the
> moment would be standard clock properties (clock-output-names etc), so
> I'm probably leaning towards a separate binding. I'll send an updated
> patchset soon.
>
> >
> > <snip>
> >> +#ifdef CONFIG_OF
> >> +/**
> >> + * of_specified_clk_setup() - Setup function for specified fixed rate clock
> >> + */
> >> +void __init of_specified_clk_setup(struct device_node *node)
> >> +{
> >> + struct clk *clk;
> >> + const char *clk_name = node->name;
> >> + u32 shift, width, rate;
> >> + void __iomem *reg;
> >> + int len, num_rates, i;
> >> + struct property *prop;
> >> + struct clk_specified_rate_entry *rates;
> >> + const __be32 *p;
> >> +
> >> + of_property_read_string(node, "clock-output-names", &clk_name);
> >> +
> >> + if (of_property_read_u32(node, "shift", &shift)) {
> >> + pr_err("%s(%s): could not read shift property\n",
> >> + __func__, clk_name);
> >> + return;
> >> + }
> >> +
> >> + if (of_property_read_u32(node, "width", &width)) {
> >> + pr_err("%s(%s): could not read width property\n",
> >> + __func__, clk_name);
> >> + return;
> >> + }
> >> +
> >> + reg = of_iomap(node, 0);
> >> + if (!reg) {
> >> + pr_err("%s(%s): of_iomap failed\n",
> >> + __func__, clk_name);
> >> + return;
> >> + }
> >> +
> >> + /* check clock-frequency exists */
> >> + prop = of_find_property(node, "clock-frequency", &len);
> >> + if (!prop) {
> >> + pr_err("%s(%s): could not find clock-frequency property\n",
> >> + __func__, clk_name);
> >> + goto err_iounmap;
> >> + }
> >> +
> >> + if (len & (sizeof(u32)*2 - 1)) {
> >> + pr_err("%s(%s): clock-frequency has invalid size of %d bytes\n",
> >> + __func__, clk_name, len);
> >> + goto err_iounmap;
> >> + }
> >> + num_rates = len / (sizeof(*rates)*2);
> >
> > This tripped me up for a few minutes. I think it is a bit weird to
> > count bytes as a way to validate length and determine the number of
> > pairs.
>
> Yes, and I actually recently discovered that this is wrong anyway. rates
> is a struct of two elements so it ends up dividing twice, and it just so
> happened that all the boards I have (until I hacked up qemu to report a
> different frequency) specify a value in the first half of those defined. :)
>
> Thanks
> James
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel



\
 
 \ /
  Last update: 2013-11-13 15:41    [W:0.066 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site