lkml.org 
[lkml]   [2013]   [Nov]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 06/12] mtd: nand: davinci: adjust DT properties to MTD generic
Date
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
---
.../devicetree/bindings/mtd/davinci-nand.txt | 25 ++++++++++++++++----
drivers/mtd/nand/davinci_nand.c | 11 ++++++---
2 files changed, 28 insertions(+), 8 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
index d2a3fc0..befaa5b 100644
--- a/Documentation/devicetree/bindings/mtd/davinci-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
@@ -37,7 +37,7 @@ Recommended properties :
- ti,davinci-mask-chipsel: mask for chipselect address. Needed to mask
addresses for given chipselect.

-- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
+- nand-ecc-mode: operation mode of the NAND ecc mode. ECC mode
valid values for davinci driver:
- "none"
- "soft"
@@ -45,10 +45,25 @@ Recommended properties :

- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.

-- ti,davinci-nand-buswidth: buswidth 8 or 16.
+- nand-bus-width: buswidth 8 or 16. If not present 8.
+
+- nand-on-flash-bbt: use flash based bad block table support. OOB
+ identifier is saved in OOB area. If not present
+ false.
+
+Deprecated properties:
+
+- ti,davinci-ecc-mode: operation mode of the NAND ecc mode. ECC mode
+ valid values for davinci driver:
+ - "none"
+ - "soft"
+ - "hw"
+
+- ti,davinci-nand-buswidth: buswidth 8 or 16. If not present 8.

- ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
- identifier is saved in OOB area.
+ identifier is saved in OOB area. If not present
+ false.

Nand device bindings may contain additional sub-nodes describing partitions of
the address space. See partition.txt for more detail. The NAND Flash timing
@@ -66,9 +81,9 @@ nand_cs3@62000000 {
ti,davinci-mask-ale = <0>;
ti,davinci-mask-cle = <0>;
ti,davinci-mask-chipsel = <0>;
- ti,davinci-ecc-mode = "hw";
+ nand-ecc-mode = "hw";
ti,davinci-ecc-bits = <4>;
- ti,davinci-nand-use-bbt;
+ nand-on-flash-bbt;

partition@180000 {
label = "ubifs";
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index 9bcbaa9..78b8d66 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -534,7 +534,6 @@ static struct davinci_nand_pdata
struct davinci_nand_pdata *pdata;
const char *mode;
u32 prop;
- int len;

pdata = devm_kzalloc(&pdev->dev,
sizeof(struct davinci_nand_pdata),
@@ -559,6 +558,8 @@ static struct davinci_nand_pdata
"ti,davinci-mask-chipsel", &prop))
pdata->mask_chipsel = prop;
if (!of_property_read_string(pdev->dev.of_node,
+ "nand-ecc-mode", &mode) ||
+ !of_property_read_string(pdev->dev.of_node,
"ti,davinci-ecc-mode", &mode)) {
if (!strncmp("none", mode, 4))
pdata->ecc_mode = NAND_ECC_NONE;
@@ -571,11 +572,15 @@ static struct davinci_nand_pdata
"ti,davinci-ecc-bits", &prop))
pdata->ecc_bits = prop;
if (!of_property_read_u32(pdev->dev.of_node,
+ "nand-bus-width", &prop) ||
+ !of_property_read_u32(pdev->dev.of_node,
"ti,davinci-nand-buswidth", &prop))
if (prop == 16)
pdata->options |= NAND_BUSWIDTH_16;
- if (of_find_property(pdev->dev.of_node,
- "ti,davinci-nand-use-bbt", &len))
+ if (of_property_read_bool(pdev->dev.of_node,
+ "nand-on-flash-bbt") ||
+ of_property_read_bool(pdev->dev.of_node,
+ "ti,davinci-nand-use-bbt"))
pdata->bbt_options = NAND_BBT_USE_FLASH;
}

--
1.7.9.5


\
 
 \ /
  Last update: 2013-11-11 18:41    [W:0.072 / U:0.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site