lkml.org 
[lkml]   [2013]   [Nov]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] phy: Add MOXA RTL8201CP PHY support
Hi Jonas,

On Friday 01 November 2013 08:24 PM, Jonas Jensen wrote:

> The MOXA UC-711X hardware(s) has an ethernet controller that seem
> to be developed internally. The IC used is "RTL8201CP".
>
> This patch adds an MDIO driver and also patches realtek to include
> RTL8201CP PHY driver.
>
> Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>

Added netdev mailing list and David Miller as I don't maintain ethernet
PHYs.

Thanks
Kishon

> ---
>
> Notes:
> The hardware does not use a separate IRQ for PHY.
>
> The link state change interrupt can instead be caught by MAC but the
> current drivers/of/of_mdio.c does not allow it to be handled in MAC.
>
> Applies to next-20131031
>
> .../devicetree/bindings/net/moxa,moxart-mdio.txt | 19 ++
> drivers/net/phy/Kconfig | 7 +
> drivers/net/phy/Makefile | 1 +
> drivers/net/phy/mdio-moxart.c | 201 +++++++++++++++++++++
> drivers/net/phy/realtek.c | 15 ++
> 5 files changed, 243 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/moxa,moxart-mdio.txt
> create mode 100644 drivers/net/phy/mdio-moxart.c
>
> diff --git a/Documentation/devicetree/bindings/net/moxa,moxart-mdio.txt b/Documentation/devicetree/bindings/net/moxa,moxart-mdio.txt
> new file mode 100644
> index 0000000..de0b90c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/moxa,moxart-mdio.txt
> @@ -0,0 +1,19 @@
> +* MOXA ART MDIO Ethernet Controller interface
> +
> +Required properties:
> +- compatible: should be "moxa,moxart-mdio".
> +- reg: address and length of the register set for the device.
> +
> +Example:
> +mdio1: mdio@92000090 {
> + compatible = "moxa,moxart-mdio";
> + reg = <0x92000090 0x8>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@1 {
> + device_type = "ethernet-phy";
> + compatible = "moxa,moxart-rtl8201cp";
> + reg = <1>;
> + };
> +};
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index 342561a..9b5d46c 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -154,6 +154,13 @@ config MDIO_SUN4I
> interface units of the Allwinner SoC that have an EMAC (A10,
> A12, A10s, etc.)
>
> +config MDIO_MOXART
> + tristate "MOXA ART MDIO interface support"
> + depends on ARCH_MOXART
> + help
> + This driver supports the MDIO interface found in the network
> + interface units of the MOXA ART SoC
> +
> config MDIO_BUS_MUX
> tristate
> depends on OF_MDIO
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index 23a2ab2..9013dfa 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -31,3 +31,4 @@ obj-$(CONFIG_MDIO_BUS_MUX) += mdio-mux.o
> obj-$(CONFIG_MDIO_BUS_MUX_GPIO) += mdio-mux-gpio.o
> obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) += mdio-mux-mmioreg.o
> obj-$(CONFIG_MDIO_SUN4I) += mdio-sun4i.o
> +obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
> diff --git a/drivers/net/phy/mdio-moxart.c b/drivers/net/phy/mdio-moxart.c
> new file mode 100644
> index 0000000..ad5d0f8
> --- /dev/null
> +++ b/drivers/net/phy/mdio-moxart.c
> @@ -0,0 +1,201 @@
> +/* MOXA ART Ethernet (RTL8201CP) MDIO interface driver
> + *
> + * Copyright (C) 2013 Jonas Jensen <jonas.jensen@gmail.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of_address.h>
> +#include <linux/of_mdio.h>
> +#include <linux/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +
> +#define REG_PHY_CTRL 0
> +#define REG_PHY_WRITE_DATA 4
> +
> +/* REG_PHY_CTRL */
> +#define MIIWR BIT(27) /* init write sequence (auto cleared)*/
> +#define MIIRD BIT(26)
> +#define REGAD_MASK 0x3e00000
> +#define PHYAD_MASK 0x1f0000
> +#define MIIRDATA_MASK 0xffff
> +
> +/* REG_PHY_WRITE_DATA */
> +#define MIIWDATA_MASK 0xffff
> +
> +struct moxart_mdio_data {
> + void __iomem *base;
> +};
> +
> +static int moxart_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
> +{
> + struct moxart_mdio_data *data = bus->priv;
> + u32 ctrl = 0;
> + unsigned int count = 5;
> +
> + dev_dbg(&bus->dev, "%s\n", __func__);
> +
> + ctrl |= MIIRD | ((mii_id << 16) & PHYAD_MASK) |
> + ((regnum << 21) & REGAD_MASK);
> +
> + writel(ctrl, data->base + REG_PHY_CTRL);
> +
> + do {
> + ctrl = readl(data->base + REG_PHY_CTRL);
> +
> + if (!(ctrl & MIIRD))
> + return ctrl & MIIRDATA_MASK;
> +
> + mdelay(10);
> + count--;
> + } while (count > 0);
> +
> + dev_err(&bus->dev, "%s timed out\n", __func__);
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int moxart_mdio_write(struct mii_bus *bus, int mii_id,
> + int regnum, u16 value)
> +{
> + struct moxart_mdio_data *data = bus->priv;
> + u32 ctrl = 0;
> + unsigned int count = 5;
> +
> + dev_dbg(&bus->dev, "%s\n", __func__);
> +
> + ctrl |= MIIWR | ((mii_id << 16) & PHYAD_MASK) |
> + ((regnum << 21) & REGAD_MASK);
> +
> + value &= MIIWDATA_MASK;
> +
> + writel(value, data->base + REG_PHY_WRITE_DATA);
> + writel(ctrl, data->base + REG_PHY_CTRL);
> +
> + do {
> + ctrl = readl(data->base + REG_PHY_CTRL);
> +
> + if (!(ctrl & MIIWR))
> + return 0;
> +
> + mdelay(10);
> + count--;
> + } while (count > 0);
> +
> + dev_err(&bus->dev, "%s timed out\n", __func__);
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int moxart_mdio_reset(struct mii_bus *bus)
> +{
> + int data, i;
> +
> + for (i = 0; i < PHY_MAX_ADDR; i++) {
> + data = moxart_mdio_read(bus, i, MII_BMCR);
> + if (data < 0)
> + continue;
> +
> + data |= BMCR_RESET;
> + if (moxart_mdio_write(bus, i, MII_BMCR, data) < 0)
> + continue;
> + }
> +
> + return 0;
> +}
> +
> +static int moxart_mdio_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct mii_bus *bus;
> + struct moxart_mdio_data *data;
> + struct resource *res;
> + int ret, i;
> +
> + bus = mdiobus_alloc_size(sizeof(*data));
> + if (!bus)
> + return -ENOMEM;
> +
> + bus->name = "MOXA ART Ethernet MII";
> + bus->read = &moxart_mdio_read;
> + bus->write = &moxart_mdio_write;
> + bus->reset = &moxart_mdio_reset;
> + snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mii", dev_name(&pdev->dev));
> + bus->parent = &pdev->dev;
> +
> + bus->irq = devm_kzalloc(&pdev->dev, sizeof(int) * PHY_MAX_ADDR,
> + GFP_KERNEL);
> + if (!bus->irq) {
> + ret = -ENOMEM;
> + goto err_out_free_mdiobus;
> + }
> +
> + /* Setting PHY_IGNORE_INTERRUPT here even if it has no effect,
> + * of_mdiobus_register() sets these PHY_POLL.
> + * Ideally, the interrupt from MAC controller could be used to
> + * detect link state changes, not polling, i.e. if there was
> + * a way phy_driver could set PHY_HAS_INTERRUPT but have that
> + * interrupt handled in ethernet drivercode.
> + */
> + for (i = 0; i < PHY_MAX_ADDR; i++)
> + bus->irq[i] = PHY_IGNORE_INTERRUPT;
> +
> + data = bus->priv;
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + data->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(data->base)) {
> + ret = PTR_ERR(data->base);
> + goto err_out_free_mdiobus;
> + }
> +
> + ret = of_mdiobus_register(bus, np);
> + if (ret < 0)
> + return ret;
> +
> + platform_set_drvdata(pdev, bus);
> +
> + return 0;
> +
> +err_out_free_mdiobus:
> + mdiobus_free(bus);
> + return ret;
> +}
> +
> +static int moxart_mdio_remove(struct platform_device *pdev)
> +{
> + struct mii_bus *bus = platform_get_drvdata(pdev);
> +
> + mdiobus_unregister(bus);
> + mdiobus_free(bus);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id moxart_mdio_dt_ids[] = {
> + { .compatible = "moxa,moxart-mdio" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, moxart_mdio_dt_ids);
> +
> +static struct platform_driver moxart_mdio_driver = {
> + .probe = moxart_mdio_probe,
> + .remove = moxart_mdio_remove,
> + .driver = {
> + .name = "moxart-mdio",
> + .of_match_table = moxart_mdio_dt_ids,
> + },
> +};
> +
> +module_platform_driver(moxart_mdio_driver);
> +
> +MODULE_DESCRIPTION("MOXA ART MDIO interface driver");
> +MODULE_AUTHOR("Jonas Jensen <jonas.jensen@gmail.com>");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> index 138de83..fa1d69a 100644
> --- a/drivers/net/phy/realtek.c
> +++ b/drivers/net/phy/realtek.c
> @@ -64,6 +64,18 @@ static int rtl8211e_config_intr(struct phy_device *phydev)
> return err;
> }
>
> +/* RTL8201CP */
> +static struct phy_driver rtl8201cp_driver = {
> + .phy_id = 0x00008201,
> + .name = "RTL8201CP Ethernet",
> + .phy_id_mask = 0x0000ffff,
> + .features = PHY_BASIC_FEATURES,
> + .flags = PHY_HAS_INTERRUPT,
> + .config_aneg = &genphy_config_aneg,
> + .read_status = &genphy_read_status,
> + .driver = { .owner = THIS_MODULE,},
> +};
> +
> /* RTL8211B */
> static struct phy_driver rtl8211b_driver = {
> .phy_id = 0x001cc912,
> @@ -98,6 +110,9 @@ static int __init realtek_init(void)
> {
> int ret;
>
> + ret = phy_driver_register(&rtl8201cp_driver);
> + if (ret < 0)
> + return -ENODEV;
> ret = phy_driver_register(&rtl8211b_driver);
> if (ret < 0)
> return -ENODEV;
>



\
 
 \ /
  Last update: 2013-11-01 19:01    [W:0.083 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site