lkml.org 
[lkml]   [2013]   [Jan]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 10/13] ARM: mm: use physical addresses in highmem sanity checks
Date
This patch modifies the highmem sanity checking code to use physical addresses
instead. This change eliminates the wrap-around problems associated with the
original virtual address based checks, and this simplifies the code a bit.

The one constraint imposed here is that low physical memory must be mapped in
a monotonically increasing fashion if there are multiple banks of memory,
i.e., x < y must => pa(x) < pa(y).

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/mm/mmu.c | 22 ++++++++++------------
1 file changed, 10 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index ef43689..e8875cb 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -929,6 +929,7 @@ phys_addr_t arm_lowmem_limit __initdata = 0;
void __init sanity_check_meminfo(void)
{
int i, j, highmem = 0;
+ phys_addr_t vmalloc_limit = __pa(vmalloc_min - 1) + 1;

for (i = 0, j = 0; i < meminfo.nr_banks; i++) {
struct membank *bank = &meminfo.bank[j];
@@ -938,8 +939,7 @@ void __init sanity_check_meminfo(void)
highmem = 1;

#ifdef CONFIG_HIGHMEM
- if (__va(bank->start) >= vmalloc_min ||
- __va(bank->start) < (void *)PAGE_OFFSET)
+ if (bank->start >= vmalloc_limit)
highmem = 1;

bank->highmem = highmem;
@@ -948,8 +948,8 @@ void __init sanity_check_meminfo(void)
* Split those memory banks which are partially overlapping
* the vmalloc area greatly simplifying things later.
*/
- if (!highmem && __va(bank->start) < vmalloc_min &&
- bank->size > vmalloc_min - __va(bank->start)) {
+ if (!highmem && bank->start < vmalloc_limit &&
+ bank->size > vmalloc_limit - bank->start) {
if (meminfo.nr_banks >= NR_BANKS) {
printk(KERN_CRIT "NR_BANKS too low, "
"ignoring high memory\n");
@@ -958,12 +958,12 @@ void __init sanity_check_meminfo(void)
(meminfo.nr_banks - i) * sizeof(*bank));
meminfo.nr_banks++;
i++;
- bank[1].size -= vmalloc_min - __va(bank->start);
- bank[1].start = __pa(vmalloc_min - 1) + 1;
+ bank[1].size -= vmalloc_limit - bank->start;
+ bank[1].start = vmalloc_limit;
bank[1].highmem = highmem = 1;
j++;
}
- bank->size = vmalloc_min - __va(bank->start);
+ bank->size = vmalloc_limit - bank->start;
}
#else
bank->highmem = highmem;
@@ -983,8 +983,7 @@ void __init sanity_check_meminfo(void)
* Check whether this memory bank would entirely overlap
* the vmalloc area.
*/
- if (__va(bank->start) >= vmalloc_min ||
- __va(bank->start) < (void *)PAGE_OFFSET) {
+ if (bank->start >= vmalloc_limit) {
printk(KERN_NOTICE "Ignoring RAM at %.8llx-%.8llx "
"(vmalloc region overlap).\n",
(unsigned long long)bank->start,
@@ -996,9 +995,8 @@ void __init sanity_check_meminfo(void)
* Check whether this memory bank would partially overlap
* the vmalloc area.
*/
- if (__va(bank->start + bank->size - 1) >= vmalloc_min ||
- __va(bank->start + bank->size - 1) <= __va(bank->start)) {
- unsigned long newsize = vmalloc_min - __va(bank->start);
+ if (bank->start + bank->size > vmalloc_limit)
+ unsigned long newsize = vmalloc_limit - bank->start;
printk(KERN_NOTICE "Truncating RAM at %.8llx-%.8llx "
"to -%.8llx (vmalloc region overlap).\n",
(unsigned long long)bank->start,
--
1.7.9.5


\
 
 \ /
  Last update: 2013-02-01 00:22    [W:0.412 / U:0.636 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site