lkml.org 
[lkml]   [2013]   [Jan]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 21/30] ARM: OMAP3: cm-t3517: Adapt to ehci-omap changes
Date
Add 2 platform devices for 'nop-usb-xceiv'. These will be used
as PHYs for HS USB ports 1 and 2 so provide binding information
for them.

Model RESET for HS USB Ports 1 and 2 as GPIO fixed regulators and
link them to the 2 PHYs we just created.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
arch/arm/mach-omap2/board-cm-t3517.c | 97 ++++++++++++++++++++++++++++++++--
1 files changed, 92 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index cfa9098..2ba97c5 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -33,6 +33,9 @@
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/can/platform/ti_hecc.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/usb/phy.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -166,15 +169,92 @@ static inline void cm_t3517_init_rtc(void) {}
#define HSUSB2_RESET_GPIO (147)
#define USB_HUB_RESET_GPIO (152)

+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct platform_device hsusb1_phy_device = {
+ .name = "nop_usb_xceiv",
+ .id = 1,
+};
+
+/* Regulator for HS USB Port 1 PHY reset */
+static struct regulator_consumer_supply hsusb1_reset_supplies[] = {
+ /* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb1_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb1_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_reset_config = {
+ .supply_name = "hsusb1_reset",
+ .microvolts = 3300000,
+ .gpio = HSUSB1_RESET_GPIO,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hsusb1_reset_data,
+};
+
+static struct platform_device hsusb1_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb1_reset_config,
+ },
+};
+
+/* PHY device on HS USB Port 2 i.e. nop_usb_xceiv.2 */
+static struct platform_device hsusb2_phy_device = {
+ .name = "nop_usb_xceiv",
+ .id = 2,
+};
+
+/* Regulator for HS USB Port 2 PHY reset */
+static struct regulator_consumer_supply hsusb2_reset_supplies[] = {
+ /* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.2"),
+};
+
+static struct regulator_init_data hsusb2_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb2_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb2_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb2_reset_config = {
+ .supply_name = "hsusb2_reset",
+ .microvolts = 3300000,
+ .gpio = HSUSB2_RESET_GPIO,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hsusb2_reset_data,
+};
+
+static struct platform_device hsusb2_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb2_reset_config,
+ },
+};
+
static struct usbhs_omap_platform_data cm_t3517_ehci_pdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};

- .phy_reset = true,
- .reset_gpio_port[0] = HSUSB1_RESET_GPIO,
- .reset_gpio_port[1] = HSUSB2_RESET_GPIO,
- .reset_gpio_port[2] = -EINVAL,
+static struct platform_device *usbhs_devices[] = {
+ &hsusb1_phy_device,
+ &hsusb1_reset_device,
+ &hsusb2_phy_device,
+ &hsusb2_reset_device,
};

static int __init cm_t3517_init_usbh(void)
@@ -191,6 +271,13 @@ static int __init cm_t3517_init_usbh(void)
msleep(1);
}

+ platform_add_devices(usbhs_devices, ARRAY_SIZE(usbhs_devices));
+
+ /* PHY on HSUSB Port 1 i.e. index 0 */
+ usb_bind_phy("ehci-omap.0", 0, "nop_usb_xceiv.1");
+ /* PHY on HSUSB Port 2 i.e. index 1 */
+ usb_bind_phy("ehci-omap.0", 1, "nop_usb_xceiv.2");
+
usbhs_init(&cm_t3517_ehci_pdata);

return 0;
--
1.7.4.1


\
 
 \ /
  Last update: 2013-01-28 15:21    [W:0.340 / U:0.668 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site