lkml.org 
[lkml]   [2013]   [Jan]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/4] Enable ecc-mode selection in the driver
On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c
>
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
> CONFIG_MTD_PHYSMAP=y
> CONFIG_MTD_M25P80=y
> CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
> CONFIG_MTD_NAND_ORION=y
> CONFIG_BLK_DEV_LOOP=y
> # CONFIG_SCSI_PROC_FS is not set
> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> index cd72b92..1a35257 100644
> --- a/drivers/mtd/nand/orion_nand.c
> +++ b/drivers/mtd/nand/orion_nand.c
> @@ -14,6 +14,7 @@
> #include <linux/module.h>
> #include <linux/platform_device.h>
> #include <linux/of.h>
> +#include <linux/of_mtd.h>
> #include <linux/mtd/mtd.h>
> #include <linux/mtd/nand.h>
> #include <linux/mtd/partitions.h>
> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> if (!of_property_read_u32(pdev->dev.of_node,
> "chip-delay", &val))
> board->chip_delay = (u8)val;
> + board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);

> } else
> board = pdev->dev.platform_data;
>
> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
> nc->cmd_ctrl = orion_nand_cmd_ctrl;
> nc->read_buf = orion_nand_read_buf;
> - nc->ecc.mode = NAND_ECC_SOFT;
> + nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> + NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;

Hi Stefan

What about a user that wants one of the other valid values?
NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

Would:

if (IS_ERR(board->ecc_mode)) {
nc->ecc.mode = NAND_ECC_SOFT;
dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
} else
nc->ecc.mode = board->ecc_mode

be better?

Andrew


\
 
 \ /
  Last update: 2013-01-15 14:21    [W:0.053 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site