lkml.org 
[lkml]   [2012]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] OMAP GPIO - don't wake from suspend unless requested.
On Thu, Sep 6, 2012 at 8:35 AM, NeilBrown <neilb@suse.de> wrote:
> On Mon, 3 Sep 2012 22:59:06 -0700 "Shilimkar, Santosh"
> <santosh.shilimkar@ti.com> wrote:
>
>> On Sun, Aug 26, 2012 at 6:29 PM, Shilimkar, Santosh
>> <santosh.shilimkar@ti.com> wrote:
>> > On Sun, Aug 26, 2012 at 3:53 PM, NeilBrown <neilb@suse.de> wrote:
>> >>
>> >> On Sun, 26 Aug 2012 09:47:50 +0530 "Shilimkar, Santosh"
>> >> <santosh.shilimkar@ti.com> wrote:
>> >>
>> >> > + Jon,
>> >> >
>> >> > On Sat, Aug 25, 2012 at 5:14 PM, NeilBrown <neilb@suse.de> wrote:
>> >> > >
>> >> > >
>> >> > >
>> >> > > Current kernel will wake from suspend on an event on any active
>> >> > > GPIO even if enable_irq_wake() wasn't called.
>> >> > >
>> >> > > There are two reasons that the hardware wake-enable bit should be set:
>> >> > >
>> >> > > 1/ while non-suspended the CPU might go into a deep sleep (off_mode)
>> >> > > in which the wake-enable bit is needed for an interrupt to be
>> >> > > recognised.
>> >> > > 2/ while suspended the GPIO interrupt should wake from suspend if and
>> >> > > only if irq_wake as been enabled.
>> >> > >
>> >> > > The code currently doesn't keep these two reasons separate so they get
>> >> > > confused and sometimes the wakeup flags is set incorrectly.
>> >> > >
>> >> > > This patch reverts:
>> >> > > commit 9c4ed9e6c01e7a8bd9079da8267e1f03cb4761fc
>> >> > > gpio/omap: remove suspend/resume callbacks
>> >> > > and
>> >> > > commit 0aa2727399c0b78225021413022c164cb99fbc5e
>> >> > > gpio/omap: remove suspend_wakeup field from struct gpio_bank
>> >> > >
>> >> > > and makes some minor changes so that we have separate flags for "GPIO
>> >> > > should wake from deep idle" and "GPIO should wake from suspend".
>> >> > >
>> >> > > With this patch, the GPIO from my touch screen doesn't wake my device
>> >> > > any more, which is what I want.
>> >> > >
>> >> > > Cc: Kevin Hilman <khilman@ti.com>
>> >> > > Cc: Tony Lindgren <tony@atomide.com>
>> >> > > Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
>> >> > > Cc: Cousson, Benoit <b-cousson@ti.com>
>> >> > > Cc: Grant Likely <grant.likely@secretlab.ca>
>> >> > > Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
>> >> > > Cc: Felipe Balbi <balbi@ti.com>
>> >> > > Cc: Govindraj.R <govindraj.raja@ti.com>
>> >> > >
>> >> > > Signed-off-by: NeilBrown <neilb@suse.de>
>> >> > >
>> >> > The patch doesn't seems to be correct. At least the 2/ gets
>> >> > fixed with a proper IRQCHIP flag. Can you try the patch at
>> >> > end of the email and see if it helps ? Am attaching it in case
>> >> > mailer damages it.
>> >> >
>> >> > Regards
>> >> > Santosh
>> >> >
>> >> > >From b8a38fc75e046f6462610e26c47c620cad850c24 Mon Sep 17 00:00:00 2001
>> >> > From: Santosh Shilimkar <santosh.shilimkar@ti.com>
>> >> > Date: Sun, 26 Aug 2012 09:39:51 +0530
>> >> > Subject: [PATCH] gpio: omap: Set IRQCHIP_MASK_ON_SUSPEND to mask all
>> >> > non-wakeup gpio wakeups.
>> >> >
>> >> > Set the irq chip flag IRQCHIP_MASK_ON_SUSPEND to cause the irq pm code
>> >> > to mask all non-wake gpios in suspend, which will ensure the wakeup
>> >> > enable
>> >> > bit is not set on non-wake gpios.
>> >> >
>> >> > Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
>> >> > ---
>> >> > drivers/gpio/gpio-omap.c | 1 +
>> >> > 1 file changed, 1 insertion(+)
>> >> >
>> >> > diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
>> >> > index e6efd77..50b4c18 100644
>> >> > --- a/drivers/gpio/gpio-omap.c
>> >> > +++ b/drivers/gpio/gpio-omap.c
>> >> > @@ -779,6 +779,7 @@ static struct irq_chip gpio_irq_chip = {
>> >> > .irq_unmask = gpio_unmask_irq,
>> >> > .irq_set_type = gpio_irq_type,
>> >> > .irq_set_wake = gpio_wake_enable,
>> >> > + .flags = IRQCHIP_MASK_ON_SUSPEND;
>> >> > };
>> >> >
>> >> >
>> >> > /*---------------------------------------------------------------------*/
>> >>
>> >>
>> >> No obvious damage, unless the mailer is responsible or the ';' at the end
>> >> of
>> >> the line, rather than ',' :-)
>> >>
>> > :-) That was typo.
>> >
>> >> The approach makes sense, but does actually work. Should be fixable
>> >> though.
>> >>
>> >> When I try this I get:
>> >>
>> >>
>> >>
>> >> [ 158.114440] Checking wakeup interrupts
>> >> [ 158.118408] Unhandled fault: external abort on non-linefetch (0x1028)
>> >> at 0xfb054040
>> >> [ 158.126403] Internal error: : 1028 [#1] PREEMPT ARM
>> >> [ 158.131500] Modules linked in: ipv6 g_ether hso libertas_sdio libertas
>> >> cfg80211
>> >> [ 158.139190] CPU: 0 Not tainted (3.5.0-gta04-debug+ #2)
>> >> [ 158.144927] PC is at _set_gpio_triggering+0x38/0x258
>> >> [ 158.150115] LR is at gpio_mask_irq+0xac/0xc0
>> >> [ 158.154602] pc : [<c01d24a0>] lr : [<c01d2f68>] psr: 60000193
>> >> [ 158.154602] sp : db521e90 ip : 00000011 fp : beeecc2c
>> >> [ 158.166595] r10: c05c8ebc r9 : daa5a858 r8 : 00000003
>> >> [ 158.172027] r7 : a0000193 r6 : 00000000 r5 : fb054000 r4 : ded44e18
>> >> [ 158.178863] r3 : 00000001 r2 : 00000000 r1 : ded30340 r0 : 00000040
>> >> [ 158.185668] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM
>> >> Segment use
>> >>
>> >> so it looks like runtime PM has turned off the iclk to the GPIO module so
>> >> that
>> >> when we try to tell it to change settings, it is no longer listening to
>> >> us.
>> > From the crash logs it appears like that.
>> >
>> >> The "Checking wakeup interrupts" function happens very late in the suspend
>> >> cycle, after all the suspend_late and suspend_noirq functions have run.
>> >> Maybe it needs to be moved earlier...
>> >>
>> > No it shouldn't be moved and it is that point for lot many good
>> > reasons. Ofcourse
>> > this omap gpio driver crash needs to be addressed. Need to think bit
>> > more on this
>> > issue.
>> >
>> After thinking bit more on this, the problem seems to be coming
>> mainly because the gpio device is runtime suspended bit early than
>> it should be. Similar issue seen with i2c driver as well. The i2c issue
>> was discussed with Rafael at LPC last week. The idea is to move
>> the pm_runtime_enable/disable() calls entirely up to the
>> _late/_early stage of device suspend/resume.
>> Will update this thread once I have further update.
>
> This won't be late enough. IRQCHIP_MASK_ON_SUSPEND takes effect after all
> the _late callbacks have been called.
> I, too, spoke to Rafael about this in San Diego. He seemed to agree with me
> that the interrupt needs to be masked in the ->suspend callback. any later
> is too late.
>
Thanks for information about your discussion. Will wait for the patch then.

Regards
santosh


\
 
 \ /
  Last update: 2012-09-06 08:22    [W:0.111 / U:0.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site