lkml.org 
[lkml]   [2012]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/3] ARM: tegra: cardhu: add dt entry for fixed regulators
Date
Cadhu have multiple power rails which are controlled by
GPIOs. Add support of these power rail control through
fixed regulators. Add entry for all fixed regulators for
cardhu-a02 and a04.
The details are taken from downstream kernel.

Some points on this change are:

* Add the tps65910-LDO5 entry and make it always ON
to supply power to SDMMC. Once the sd driver support
regulator handling, this flag will be remove.

* Dropping registration of rail vdd_sdmmc1 as the gpio
is used by sdhci power-gpio. This need to fix in
sdhci driver and then need to add the registration
mechanism. Just removing power-gpio and adding fixed
regulator with this gpio is causing the sd access to
fail because first probe call of this regulator fails
due to non-available of parent and so it calls
gpio_free() which disable the pins in gpio mode make
pin output to LOW causes power to OFF. In probe retry,
it got success and it powered-on but it again need to
do again numeration of card here.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1-->V2:
- Remove the vdd_sdmmc1 regulator registration.
- Fix the pex_hvdd_3v3 regulator registration.
- Set panel regulator to be always on.

arch/arm/boot/dts/tegra30-cardhu-a02.dts | 76 +++++++++++++++
arch/arm/boot/dts/tegra30-cardhu-a04.dts | 88 ++++++++++++++++++
arch/arm/boot/dts/tegra30-cardhu.dtsi | 147 ++++++++++++++++++++++++++++++
3 files changed, 311 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/tegra30-cardhu-a02.dts b/arch/arm/boot/dts/tegra30-cardhu-a02.dts
index dd870b7..dd4222f 100644
--- a/arch/arm/boot/dts/tegra30-cardhu-a02.dts
+++ b/arch/arm/boot/dts/tegra30-cardhu-a02.dts
@@ -7,5 +7,81 @@
/ {
model = "NVIDIA Tegra30 Cardhu A02 evaluation board";
compatible = "nvidia,cardhu-a02", "nvidia,cardhu", "nvidia,tegra30";
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddr_reg: regulator@100 {
+ compatible = "regulator-fixed";
+ reg = <100>;
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pmic 6 0>;
+ };
+
+ sys_3v3_reg: regulator@101 {
+ compatible = "regulator-fixed";
+ reg = <101>;
+ regulator-name = "sys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pmic 7 0>;
+ };
+
+ usb1_vbus_reg: regulator@102 {
+ compatible = "regulator-fixed";
+ reg = <102>;
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 68 0>; /* GPIO PI4 */
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_reg>;
+ };
+
+ usb3_vbus_reg: regulator@103 {
+ compatible = "regulator-fixed";
+ reg = <103>;
+ regulator-name = "usb3_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 63 0>; /* GPIO PH7 */
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_reg>;
+ };
+
+ vdd_5v0_reg: regulator@104 {
+ compatible = "regulator-fixed";
+ reg = <104>;
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pmic 2 0>;
+ };
+
+ vdd_bl_reg: regulator@105 {
+ compatible = "regulator-fixed";
+ reg = <105>;
+ regulator-name = "vdd_bl";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio 83 0>; /* GPIO PK3 */
+ };
+ };
};

diff --git a/arch/arm/boot/dts/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
index a4cae6c..0828f09 100644
--- a/arch/arm/boot/dts/tegra30-cardhu-a04.dts
+++ b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
@@ -7,4 +7,92 @@
/ {
model = "NVIDIA Tegra30 Cardhu A04 (A05, A06, A07) evaluation board";
compatible = "nvidia,cardhu-a04", "nvidia,cardhu", "nvidia,tegra30";
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddr_reg: regulator@100 {
+ compatible = "regulator-fixed";
+ regulator-name = "ddr";
+ reg = <100>;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pmic 7 0>;
+ };
+
+ sys_3v3_reg: regulator@101 {
+ compatible = "regulator-fixed";
+ reg = <101>;
+ regulator-name = "sys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pmic 6 0>;
+ };
+
+ usb1_vbus_reg: regulator@102 {
+ compatible = "regulator-fixed";
+ reg = <102>;
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 238 0>; /* GPIO PDD6 */
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_reg>;
+ };
+
+ usb3_vbus_reg: regulator@103 {
+ compatible = "regulator-fixed";
+ reg = <103>;
+ regulator-name = "usb3_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 236 0>; /* GPIO PDD4 */
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_reg>;
+ };
+
+ vdd_5v0_reg: regulator@104 {
+ compatible = "regulator-fixed";
+ reg = <104>;
+ regulator-name = "5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pmic 8 0>;
+ };
+
+ vdd_bl_reg: regulator@105 {
+ compatible = "regulator-fixed";
+ reg = <105>;
+ regulator-name = "vdd_bl";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio 234 0>; /* GPIO PDD2 */
+ };
+
+ vdd_bl2_reg: regulator@106 {
+ compatible = "regulator-fixed";
+ reg = <106>;
+ regulator-name = "vdd_bl2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio 232 0>; /* GPIO PDD0 */
+ };
+ };
};
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi
index ba38527..4794693 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
@@ -162,6 +162,7 @@
vcc1-supply = <&vdd_ac_bat_reg>;
vcc2-supply = <&vdd_ac_bat_reg>;
vcc3-supply = <&vio_reg>;
+ vcc4-supply = <&vdd_5v0_reg>;
vcc5-supply = <&vdd_ac_bat_reg>;
vcc6-supply = <&vdd2_reg>;
vcc7-supply = <&vdd_ac_bat_reg>;
@@ -234,6 +235,15 @@
regulator-always-on;
};

+ ldo5_reg: regulator@8 {
+ reg = <8>;
+ regulator-compatible = "ldo5";
+ regulator-name = "vddio_sdmmc,avdd_vdac";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
ldo6_reg: regulator@9 {
reg = <9>;
regulator-compatible = "ldo6";
@@ -300,6 +310,143 @@
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
+
+ cam_1v8_reg: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "cam_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&gpio 220 0>; /* gpio PBB4 */
+ vin-supply = <&vio_reg>;
+ };
+
+ cp_5v_reg: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "cp_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&pmic 0 0>; /* PMIC TPS65911 GPIO0 */
+ };
+
+ emmc_3v3_reg: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "emmc_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio 25 0>; /* gpio PD1 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ modem_3v3_reg: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "modem_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio 30 0>; /* gpio PD6 */
+ };
+
+ pex_hvdd_3v3_reg: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "pex_hvdd_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio 95 0>; /* gpio PL7 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_cam1_ldo_reg: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "vdd_cam1_ldo";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ enable-active-high;
+ gpio = <&gpio 142 0>; /* gpio PR6 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_cam2_ldo_reg: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "vdd_cam2_ldo";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ enable-active-high;
+ gpio = <&gpio 143 0>; /* gpio PR7 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_cam3_ldo_reg: regulator@8 {
+ compatible = "regulator-fixed";
+ reg = <8>;
+ regulator-name = "vdd_cam3_ldo";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio 144 0>; /* gpio PS0 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_com_reg: regulator@9 {
+ compatible = "regulator-fixed";
+ reg = <9>;
+ regulator-name = "vdd_com";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio 24 0>; /* gpio PD0 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_fuse_3v3_reg: regulator@10 {
+ compatible = "regulator-fixed";
+ reg = <10>;
+ regulator-name = "vdd_fuse_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio 94 0>; /* gpio PL6 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_pnl1_reg: regulator@11 {
+ compatible = "regulator-fixed";
+ reg = <11>;
+ regulator-name = "vdd_pnl1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio 92 0>; /* gpio PL4 */
+ vin-supply = <&sys_3v3_reg>;
+ };
+
+ vdd_vid_reg: regulator@12 {
+ compatible = "regulator-fixed";
+ reg = <12>;
+ regulator-name = "vddio_vid";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 152 0>; /* GPIO PT0 */
+ gpio-open-drain;
+ vin-supply = <&vdd_5v0_reg>;
+ };
};

sound {
--
1.7.1.1


\
 
 \ /
  Last update: 2012-08-09 14:02    [W:0.048 / U:1.396 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site