Messages in this thread Patch in this message | | | From | Lee Jones <> | Subject | [PATCH] ARM: ux500: Provide SMSC911x fixed-regulator when not booting DT | Date | Fri, 24 Aug 2012 13:00:12 +0100 |
| |
The SMSC911x Ethernet chip requires a fixed-regulator in order to function correctly. We have previously provided a means to obtain this during a Device Tree boot, however nothing has been put into place when booting with a non-DT kernel. This patch aims to change that.
Signed-off-by: Lee Jones <lee.jones@linaro.org> --- arch/arm/mach-ux500/board-mop500-regulators.c | 17 +++++++++++++++++ arch/arm/mach-ux500/board-mop500-regulators.h | 1 + arch/arm/mach-ux500/board-mop500.c | 21 +++++++++++++++++++++ arch/arm/mach-ux500/board-mop500.h | 2 +- 4 files changed, 40 insertions(+), 1 deletion(-)
diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c b/arch/arm/mach-ux500/board-mop500-regulators.c index 52426a4..11ddda7 100644 --- a/arch/arm/mach-ux500/board-mop500-regulators.c +++ b/arch/arm/mach-ux500/board-mop500-regulators.c @@ -13,6 +13,23 @@ #include <linux/regulator/ab8500.h> #include "board-mop500-regulators.h" +#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE +static struct regulator_consumer_supply gpio_en_3v3_consumers[] = { + REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), +}; + +struct regulator_init_data gpio_en_3v3_regulator = { + .constraints = { + .name = "EN-3V3", + .min_uV = 3300000, + .max_uV = 3300000, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(gpio_en_3v3_consumers), + .consumer_supplies = gpio_en_3v3_consumers, +}; +#endif + /* * TPS61052 regulator */ diff --git a/arch/arm/mach-ux500/board-mop500-regulators.h b/arch/arm/mach-ux500/board-mop500-regulators.h index 9499215..78a0642 100644 --- a/arch/arm/mach-ux500/board-mop500-regulators.h +++ b/arch/arm/mach-ux500/board-mop500-regulators.h @@ -18,5 +18,6 @@ extern struct ab8500_regulator_reg_init ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS]; extern struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS]; extern struct regulator_init_data tps61052_regulator; +extern struct regulator_init_data gpio_en_3v3_regulator; #endif diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index de10f8f..0e904c8 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -23,6 +23,7 @@ #include <linux/spi/spi.h> #include <linux/mfd/abx500/ab8500.h> #include <linux/regulator/ab8500.h> +#include <linux/regulator/fixed.h> #include <linux/mfd/tc3589x.h> #include <linux/mfd/tps6105x.h> #include <linux/mfd/abx500/ab8500-gpio.h> @@ -75,6 +76,25 @@ static struct platform_device snowball_led_dev = { }, }; +#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE +static struct fixed_voltage_config snowball_gpio_en_3v3_data = { + .supply_name = "EN-3V3", + .gpio = SNOWBALL_EN_3V3_ETH_GPIO, + .microvolts = 3300000, + .enable_high = 1, + .init_data = &gpio_en_3v3_regulator, + .startup_delay = 5000, /* 1200us */ +}; + +static struct platform_device snowball_gpio_en_3v3_regulator_dev = { + .name = "reg-fixed-voltage", + .id = 1, + .dev = { + .platform_data = &snowball_gpio_en_3v3_data, + }, +}; +#endif + static struct ab8500_gpio_platform_data ab8500_gpio_pdata = { .gpio_base = MOP500_AB8500_PIN_GPIO(1), .irq_base = MOP500_AB8500_VIR_GPIO_IRQ_BASE, @@ -585,6 +605,7 @@ static struct platform_device *snowball_platform_devs[] __initdata = { &snowball_led_dev, &snowball_key_dev, &snowball_sbnet_dev, + &snowball_gpio_en_3v3_regulator_dev, }; static void __init mop500_init_machine(void) diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index a0f920d..4ace165 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -13,6 +13,7 @@ #include <linux/amba/mmci.h> /* Snowball specific GPIO assignments, this board has no GPIO expander */ +#define SNOWBALL_EN_3V3_ETH_GPIO 26 #define SNOWBALL_ACCEL_INT1_GPIO 163 #define SNOWBALL_ACCEL_INT2_GPIO 164 #define SNOWBALL_MAGNET_DRDY_GPIO 165 @@ -76,7 +77,6 @@ #define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */ #define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */ #define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */ -#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */ struct device; struct i2c_board_info; -- 1.7.9.5
| |