lkml.org 
[lkml]   [2012]   [Apr]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: psmouse serio4: bad data from KBC - timeout
Hi Dmitry,

On Tue, Apr 03, 2012 at 10:06:59AM -0700, Dmitry Torokhov wrote:
> > I'm running 3.4-rc1 on a thinkpad x121e and it builds and boots just
> > fine. However, after resuming from disk I get (this is the tail of
> > dmesg):
> >
> > [ 905.857412] i8042: failed to resume active multiplexor, mouse won't work
> > [ 905.965568] usb 3-2: reset low-speed USB device number 2 using ohci_hcd
> > [ 907.626998] psmouse serio4: bad data from KBC - timeout
> > [ 907.675385] PM: restore of devices complete after 2358.155 msecs
> > [ 908.227481] Restarting tasks ... done.
> > [ 908.266229] video LNXVIDEO:01: Restoring backlight state
> > [ 917.628792] psmouse serio4: Failed to deactivate mouse on isa0060/serio4
> > [ 917.880639] psmouse serio4: Failed to enable mouse on isa0060/serio4
> > [ 919.867982] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input19
> > [ 947.277011] atl1c 0000:02:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
> > [ 996.231116] Bluetooth: Core ver 2.16
> > [ 996.231262] NET: Registered protocol family 31
> > [ 996.231273] Bluetooth: HCI device and connection manager initialized
> > [ 996.231559] Bluetooth: HCI socket layer initialized
> > [ 996.231575] Bluetooth: L2CAP socket layer initialized
> > [ 996.231630] Bluetooth: SCO socket layer initialized
> >
> > and after that the keyboard and the mouse touchpad don't work. The
> > connected USB mouse works fine though.
>
> There weren't any changes to i8042 for a while so I'd look into recent
> ACPI/PM merges. You can also try booting with i8042.nomux to see if it
> will work better with i8042 in legacy multiplexing mode.

thanks for looking into this.

So, I just tested the "i8042.nomux" command line option and it seems to
work. Even the touchpad went on after rubbing on it a couple of times
initially.

Then, I booted back into 3.4-rc1 without the above option and here's
what I got again:

[ 0.924424] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 0.928313] i8042: Detected active multiplexing controller, rev 1.1
[ 0.929966] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.930628] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.930890] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.931175] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.931343] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.971523] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 2.086110] psmouse serio4: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00
[ 2.086378] psmouse serio4: synaptics: serio: Synaptics pass-through port at isa0060/serio4/input0
[ 2.127547] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input1
[ 7.880045] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio4/serio5/input/input2
[ 193.757348] i8042: failed to resume active multiplexor, mouse won't work

It seems the mux controller doesn't resume properly (doh, it says so
:)) so not only mousepad but keyboard is not working too.

Actually, that's not 100% correct: the keyboard does work for a short
period of time (a couple of seconds, judging by the printk timestamps
below) right after I resume and then it stops ...

[ 195.526425] psmouse serio4: bad data from KBC - timeout
[ 205.532397] psmouse serio4: Failed to deactivate mouse on isa0060/serio4
[ 205.772260] psmouse serio4: Failed to enable mouse on isa0060/serio4
[ 207.447644] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input15

.. with the above being the last line on dmesg.

So, I'm ready for suggestions.

Thanks.

--
Regards/Gruss,
Boris.


\
 
 \ /
  Last update: 2012-04-04 06:57    [W:0.040 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site