lkml.org 
[lkml]   [2012]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V5 2/2] mfd: stmpe: Update DT support in stmpe driver
> Ping!!!

Documentation/development-process/2.Process:

- Avoid top-posting (the practice of putting your answer above the quoted
text you are responding to). It makes your response harder to read and
makes a poor impression.

:)

> On 1 December 2012 00:33, Viresh Kumar <viresh.kumar@linaro.org> wrote:
> > On 30 November 2012 21:15, Lee Jones <lee.jones@linaro.org> wrote:
> >> But ... I don't see how the changes in the -i2c and -spi files
> >> are of benefit either. When I boot without the ID table I still
> >> get "stmpe-i2c 0-0040: stmpe1601 detected, chip id: 0x212".
> >>
> >> What is it that actually uses the IDs?
> >>
> >> Perhaps Viresh can shine some light on the matter?
> >
> > As you can see, i wasn't the author of this patch and when you asked
> > this question, i didn't had an answer to it. I went through code and
> > formed some theory/story :) .
> >
> > @Grant: i need your help to check if my theory is correct or not. Question
> > is about adding below code in any i2c client driver:
> >
> > +#ifdef CONFIG_OF
> > +static const struct of_device_id stmpe_dt_ids[] = {
> > + { .compatible = "st,stmpe610", .data = &stmpe_i2c_id[0], },
> > + { .compatible = "st,stmpe801", .data = &stmpe_i2c_id[1], },
> > + { .compatible = "st,stmpe811", .data = &stmpe_i2c_id[2], },
> > + { .compatible = "st,stmpe1601", .data = &stmpe_i2c_id[3], },
> > + { .compatible = "st,stmpe2401", .data = &stmpe_i2c_id[4], },
> > + { .compatible = "st,stmpe2403", .data = &stmpe_i2c_id[5], },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, stmpe_dt_ids);
> > +#endif
> > +
> > static struct i2c_driver stmpe_i2c_driver = {
> > .driver = {
> > .name = "stmpe-i2c",
> > @@ -88,6 +102,7 @@ static struct i2c_driver stmpe_i2c_driver = {
> > #ifdef CONFIG_PM
> > .pm = &stmpe_dev_pm_ops,
> > #endif
> > + .of_match_table = of_match_ptr(stmpe_dt_ids),
> >
> > So, what is the use of this table when we already have i2c_driver.id_table
> > populated.
> >
> > This is my theory:
> > ---------------------
> > Adapter drivers supporting DT will call:
> > of_i2c_register_devices()
> > {
> > for_each_child_of_node(adap->dev.of_node, node) {
> > if (of_modalias_node(node, info.type, sizeof(info.type)) < 0)
> > error condition
> >
> > ...
> > result = i2c_new_device(adap, &info);
> >
> > ...
> > }
> >
> > of_modalias_node(): expects compatible in child node, i.e. stmpe node in our
> > case. If it is not there, then that node is skipped. then it copies
> > string after ','
> > to info.type. So, for us only "stmpe810" out of "st,stmpe810" is copied.
> >
> > Now this name, i.e. "stmpe810" is copied as client.name in i2c_new_device()
> > and device_register() is called, which will eventually call:
> >
> > i2c_device_match()
> > {
> > /* Attempt an OF style match */
> > if (of_driver_match_device(dev, drv))
> > return 1;
> >
> > driver = to_i2c_driver(drv);
> > /* match on an id table if there is one */
> > if (driver->id_table)
> > return i2c_match_id(driver->id_table, client) != NULL;
> > }
> >
> > This first tries to match the table my patch added, _BUT_ the string will
> > never match as we had "st,stmpe810" in table and "stmpe810" in dev.
> >
> > So, we fall back to i2c_match_id(), which will match it against
> > i2c_driver.id_table present in driver, which has entry for "stmpe810" and
> > so strings matched.
> >
> > @Lee: This is what happened in your case. :)
> >
> > So, whether its DT or non DT, true is returned from here if something
> > matched.
> >
> > Later on, this will be called:
> >
> > static int i2c_device_probe(struct device *dev)
> > {
> > .....
> > status = driver->probe(client, i2c_match_id(driver->id_table, client));
> > ....
> > }
> >
> > Which will again match the legacy table to find correct struct i2c_device_id *id
> > to pass to probe().
> >
> > So, the final question: WTF is of_match_table for?
> >
> > Then i thought maybe it is used when we don't have child nodes inside parent,
> > something related to the phandle way ? I grep'd i2c in arch/arm/boot/dts and
> > couldn't find anything of that sort, the way i2c clients are added is:
> >
> > in dtsi file:
> >
> > i2c0: i2c@address {
> > ...
> > }
> >
> > in dts file:
> > &i2c0 {
> > stmpe810 {
> > ........
> > }
> > }
> >
> > which i believe will be taken care by dtc and will fold client nodes
> > as child nodes
> > of i2c0.
> >
> > @Grant: Please throw some light here :)
> >
> > --
> > viresh

--
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2012-12-05 15:02    [W:0.399 / U:0.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site