lkml.org 
[lkml]   [2012]   [Dec]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 2/2]linux-usb:optimize to match the Huawei USB storage devices and support new switch command
Date
Dear Sebastian:
Please see the comments follows yours.

By the way, I found the kernel is updated to 3.7.1 today. So I have to update my patch based on 3.7.1, and resubmit it?
Right?

Best Regards,
Franko Fang

> -----Original Message-----
> From: Sebastian Andrzej Siewior [mailto:sebastian@breakpoint.cc]
> Sent: Tuesday, December 18, 2012 10:10 PM
> To: Fangxiaozhi (Franko)
> Cc: linux-usb@vger.kernel.org; linux-kernel@vger.kernel.org; Xueguiying
> (Zihan); Linlei (Lei Lin); greg@kroah.com; Yili (Neil); Wangyuhua (Roger,
> Credit); Huqiao; balbi@ti.com
> Subject: Re: [PATCH 2/2]linux-usb:optimize to match the Huawei USB
> storage devices and support new switch command
>
> On Tue, Dec 18, 2012 at 10:44:19AM +0800, fangxiaozhi 00110321 wrote:
> > diff -uprN linux-3.7_bak/drivers/usb/storage/initializers.c
> linux-3.7/drivers/usb/storage/initializers.c
> > --- linux-3.7_bak/drivers/usb/storage/initializers.c 2012-12-11
> 09:56:11.000000000 +0800
> > +++ linux-3.7/drivers/usb/storage/initializers.c 2012-12-17
> 11:12:12.000000000 +0800
> > US_DEBUGP("Huawei mode set result is %d\n", result);
> > return 0;
> > }
> > +
> > +/* Find the supported Huawei USB dongles */ static int
> > +usb_stor_huawei_dongles_pid(struct us_data *us) {
> > + struct usb_interface_descriptor *idesc;
> > + int idProduct;
> > +
> > + idesc = &us->pusb_intf->cur_altsetting->desc;
> > + idProduct = us->pusb_dev->descriptor.idProduct;
> > + if (idesc && idesc->bInterfaceNumber == 0) {
> > + if ((idProduct == 0x1001)
> > + || (idProduct == 0x1003)
> > + || (idProduct == 0x1004)
> > + || (idProduct >= 0x1401 && idProduct < 0x1501)
> > + || (idProduct > 0x1504 && idProduct <= 0x1600)
> > + || (idProduct >= 0x1c02 && idProduct <= 0x2202)) {
> > + return 1;
> > + }
> > + }
> > + return 0;
> > +}
> > +
> > +static int usb_stor_huawei_scsi_init(struct us_data *us) {
> > + int result = 0;
> > + int act_len = 0;
> > + char rewind_cmd[] = {0x11, 0x06, 0x20, 0x00, 0x00, 0x01, 0x01, 0x00,
> > + 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
>
> Has this something to do with the SPACE command as defined in SSC-2? I
> don't see the code (0x6 here) to be defined. But then you name is rewind.

Yes, we redefine the SPACE based on our need, and named it "rewind"

>
> > + struct bulk_cb_wrap *bcbw = (struct bulk_cb_wrap *) us->iobuf;
> > +
> > + memset(bcbw, 0, sizeof(struct bulk_cb_wrap));
> > + bcbw->Signature = cpu_to_le32(US_BULK_CB_SIGN);
> > + bcbw->Tag = 0;
> > + bcbw->DataTransferLength = 0;
> > + bcbw->Flags = bcbw->Lun = 0;
>
> A memset() followed by an init of each member of the struct. Could please
> chose one side?
>
> > + bcbw->Length = sizeof(rewind_cmd);
> > + memcpy(bcbw->CDB, rewind_cmd, sizeof(rewind_cmd));
> > +
> > + result = usb_stor_bulk_transfer_buf(us, us->send_bulk_pipe, &bcbw,
> > + US_BULK_CS_WRAP_LEN, &act_len);
>
> I am a little confused here. Shouldn't this be bcbw aka us->iobuf and not
> &bcbw ?
Yes, you are right.
>
> And shouldn't you read something from the us->recv_bulk_pipe after
> that?
Well, because our device will re-connect to switch the ports if it receives the command.
So it is not necessary to read the response of the command.
>
> > + US_DEBUGP("transfer actual length=%d, result=%d\n", act_len,
> result);
> > + return result;
> > +}
> > +
>
> Sebastian
\
 
 \ /
  Last update: 2012-12-19 05:01    [W:0.052 / U:1.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site