lkml.org 
[lkml]   [2012]   [Dec]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: WARNING: at drivers/gpu/drm/i915/intel_display.c:1009 ironlake_crtc_disable+0xaf/0x8e0
> >> I tried 3.7-rc5 on an ironlale PC and got the warning in subject. The
> >> computer last ran 3.6.0 without any warnings. Second reboot showed the
> >> same warning plus a couple of EDID warnings (also below).
> >
> > Still there with 3.7.0-rc7-00113-gcc19528 and 100% reproducible:
>
> Hm, can you please boot with drm.debug=0xe added to your kernel
> cmdline and the attach the complete dmesg?

Here you are. This time the EDID warning is there too, seems to depend
on timing.

[ 0.000000] Linux version 3.7.0-rc7-00113-gcc19528 (mroos@prometheus) (gcc version 4.7.2 (Debian 4.7.2-4) ) #75 SMP Fri Nov 30 22:40:48 EET 2012
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.7.0-rc7-00113-gcc19528 root=/dev/sda1 ro drm.debug=0xe
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e8000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000db7ac43f] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db7ac440-0x00000000db7ae49f] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000db7ae4a0-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fed3ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed45000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000117ffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: Hewlett-Packard HP Compaq 8100 Elite SFF PC/304Ah, BIOS 786H1 v01.13 07/14/2011
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x118000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E3FFF write-protect
[ 0.000000] E4000-EFFFF write-back
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask E00000000 write-back
[ 0.000000] 1 base 0DB800000 mask FFF800000 uncachable
[ 0.000000] 2 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 3 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xdb800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdb7ac max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f9bf0-0x000f9bff] mapped at [ffff8800000f9bf0]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0xdb7abfff]
[ 0.000000] [mem 0x00000000-0xdb5fffff] page 2M
[ 0.000000] [mem 0xdb600000-0xdb7abfff] page 4k
[ 0.000000] kernel direct mapping tables up to 0xdb7abfff @ [mem 0x1fffa000-0x1fffffff]
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x117ffffff]
[ 0.000000] [mem 0x100000000-0x117ffffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0x117ffffff @ [mem 0xdb7aa000-0xdb7abfff]
[ 0.000000] ACPI: RSDP 00000000000e5210 00014 (v00 COMPAQ)
[ 0.000000] ACPI: RSDT 00000000db7d0540 00040 (v01 HPQOEM SLIC-BPC 20110714 00000000)
[ 0.000000] ACPI: FACP 00000000db7d05e8 00074 (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI BIOS Bug: Warning: Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000050/0x0 (20120913/tbfadt-598)
[ 0.000000] ACPI BIOS Bug: Warning: Invalid length for FADT/Pm2ControlBlock: 0, using default 8 (20120913/tbfadt-648)
[ 0.000000] ACPI: DSDT 00000000db7d0a4f 0A69E (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
[ 0.000000] ACPI: FACS 00000000db7d0500 00040
[ 0.000000] ACPI: APIC 00000000db7d065c 000BC (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: ASF! 00000000db7d0718 00063 (v32 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: MCFG 00000000db7d077b 0003C (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: TCPA 00000000db7d07b7 00032 (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: SLIC 00000000db7d07e9 00176 (v01 HPQOEM SLIC-BPC 00000001 00000000)
[ 0.000000] ACPI: HPET 00000000db7d095f 00038 (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880113800000-ffff8801175fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x117ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xdb7abfff]
[ 0.000000] node 0: [mem 0x100000000-0x117ffffff]
[ 0.000000] On node 0 totalpages: 997179
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3913 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 16320 pages used for memmap
[ 0.000000] DMA32 zone: 878572 pages, LIFO batch:31
[ 0.000000] Normal zone: 1536 pages used for memmap
[ 0.000000] Normal zone: 96768 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0xf808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000db7ac000 - 00000000db7ad000
[ 0.000000] PM: Registered nosave memory: 00000000db7ad000 - 00000000db7ae000
[ 0.000000] PM: Registered nosave memory: 00000000db7ae000 - 00000000db7af000
[ 0.000000] PM: Registered nosave memory: 00000000db7af000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f4000000
[ 0.000000] PM: Registered nosave memory: 00000000f4000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fe000000
[ 0.000000] PM: Registered nosave memory: 00000000fe000000 - 00000000fed40000
[ 0.000000] PM: Registered nosave memory: 00000000fed40000 - 00000000fed45000
[ 0.000000] PM: Registered nosave memory: 00000000fed45000 - 0000000100000000
[ 0.000000] e820: [mem 0xe0000000-0xf3ffffff] available for PCI devices
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880117c00000 s74048 r8192 d24256 u262144
[ 0.000000] pcpu-alloc: s74048 r8192 d24256 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 979253
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.7.0-rc7-00113-gcc19528 root=/dev/sda1 ro drm.debug=0xe
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Memory: 3842432k/4587520k available (4388k kernel code, 598804k absent, 146284k reserved, 4151k data, 492k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:744 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 3325.043 MHz processor
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 6650.08 BogoMIPS (lpj=13300172)
[ 0.000062] pid_max: default: 32768 minimum: 301
[ 0.000111] Mount-cache hash table entries: 256
[ 0.000264] CPU: Physical Processor ID: 0
[ 0.000291] CPU: Processor Core ID: 0
[ 0.000320] mce: CPU supports 9 MCE banks
[ 0.000353] CPU0: Thermal monitoring enabled (TM1)
[ 0.000385] process: using mwait in idle threads
[ 0.000416] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
[ 0.000416] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
[ 0.000416] tlb_flushall_shift: 6
[ 0.000565] Freeing SMP alternatives: 20k freed
[ 0.000599] ACPI: Core revision 20120913
[ 0.004742] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.044337] smpboot: CPU0: Intel(R) Core(TM) i5 CPU 660 @ 3.33GHz (fam: 06, model: 25, stepping: 05)
[ 0.151288] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere events, Intel PMU driver.
[ 0.151369] perf_event_intel: CPUID marked event: 'bus cycles' unavailable
[ 0.151408] ... version: 3
[ 0.151440] ... bit width: 48
[ 0.151472] ... generic registers: 4
[ 0.151505] ... value mask: 0000ffffffffffff
[ 0.151540] ... max period: 000000007fffffff
[ 0.151575] ... fixed-purpose events: 3
[ 0.151607] ... event mask: 000000070000000f
[ 0.165026] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.151766] smpboot: Booting Node 0, Processors #1 #2 #3
[ 0.191401] Brought up 4 CPUs
[ 0.191455] smpboot: Total of 4 processors activated (26600.34 BogoMIPS)
[ 0.193280] PM: Registering ACPI NVS region [mem 0xdb7ac440-0xdb7ae49f] (8288 bytes)
[ 0.193348] reboot: BIOS series board detected. Selecting HP Compaq Laptop-method for reboots.
[ 0.193451] NET: Registered protocol family 16
[ 0.193555] ACPI: bus type pci registered
[ 0.193624] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[ 0.193689] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[ 0.196315] PCI: Using configuration type 1 for base access
[ 0.196729] bio: create slab <bio-0> at 0
[ 0.196796] ACPI: Added _OSI(Module Device)
[ 0.196830] ACPI: Added _OSI(Processor Device)
[ 0.196864] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.196898] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.197424] ACPI: EC: Look up EC in DSDT
[ 0.242075] ACPI: SSDT 00000000db7dc771 003BA (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.242308] ACPI: Dynamic OEM Table Load:
[ 0.242349] ACPI: SSDT (null) 003BA (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.273972] ACPI: SSDT 00000000db7dc399 003D8 (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.274185] ACPI: Dynamic OEM Table Load:
[ 0.274225] ACPI: SSDT (null) 003D8 (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.321964] ACPI: Interpreter enabled
[ 0.321998] ACPI: (supports S0 S3 S4 S5)
[ 0.322055] ACPI: Using IOAPIC for interrupt routing
[ 0.339634] ACPI: No dock devices found.
[ 0.339669] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.339878] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20120913/dsfield-211)
[ 0.339955] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880113432668), AE_ALREADY_EXISTS (20120913/psparse-536)
[ 0.340043] ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
[ 0.340113] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20120913/nspredef-359)
[ 0.340192] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.340405] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.340494] PCI host bridge to bus 0000:00
[ 0.341019] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.341056] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfdffffff]
[ 0.341095] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.341133] pci_bus 0000:00: root bus resource [io 0x1000-0x2fff]
[ 0.341171] pci_bus 0000:00: root bus resource [io 0x3000-0x6fff]
[ 0.341209] pci_bus 0000:00: root bus resource [io 0x7000-0xafff]
[ 0.341246] pci_bus 0000:00: root bus resource [io 0xb000-0xffff]
[ 0.341284] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.341324] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xf3ffffff]
[ 0.341363] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.341408] pci 0000:00:00.0: [8086:0040] type 00 class 0x060000
[ 0.341420] DMAR: Disabling batched IOTLB flush on Ironlake
[ 0.341470] pci 0000:00:02.0: [8086:0042] type 00 class 0x030000
[ 0.341478] pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf03fffff 64bit]
[ 0.341482] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.341485] pci 0000:00:02.0: reg 20: [io 0x1170-0x1177]
[ 0.341527] pci 0000:00:16.0: [8086:3b64] type 00 class 0x078000
[ 0.341552] pci 0000:00:16.0: reg 10: [mem 0xf0427100-0xf042710f 64bit]
[ 0.341639] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.341660] pci 0000:00:16.3: [8086:3b67] type 00 class 0x070002
[ 0.341673] pci 0000:00:16.3: reg 10: [io 0x1188-0x118f]
[ 0.341680] pci 0000:00:16.3: reg 14: [mem 0xf0424000-0xf0424fff]
[ 0.341766] pci 0000:00:19.0: [8086:10ef] type 00 class 0x020000
[ 0.341779] pci 0000:00:19.0: reg 10: [mem 0xf0400000-0xf041ffff]
[ 0.341785] pci 0000:00:19.0: reg 14: [mem 0xf0425000-0xf0425fff]
[ 0.341791] pci 0000:00:19.0: reg 18: [io 0x1100-0x111f]
[ 0.341840] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.341858] pci 0000:00:1a.0: [8086:3b3c] type 00 class 0x0c0320
[ 0.341874] pci 0000:00:1a.0: reg 10: [mem 0xf0426800-0xf0426bff]
[ 0.341947] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.341966] pci 0000:00:1b.0: [8086:3b56] type 00 class 0x040300
[ 0.341977] pci 0000:00:1b.0: reg 10: [mem 0xf0420000-0xf0423fff 64bit]
[ 0.342028] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.342044] pci 0000:00:1c.0: [8086:3b42] type 01 class 0x060400
[ 0.342095] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.342114] pci 0000:00:1c.4: [8086:3b4a] type 01 class 0x060400
[ 0.342165] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.342181] pci 0000:00:1c.6: [8086:3b4e] type 01 class 0x060400
[ 0.342232] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[ 0.342253] pci 0000:00:1d.0: [8086:3b34] type 00 class 0x0c0320
[ 0.342270] pci 0000:00:1d.0: reg 10: [mem 0xf0426c00-0xf0426fff]
[ 0.342340] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.342356] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.342404] pci 0000:00:1f.0: [8086:3b0a] type 00 class 0x060100
[ 0.342505] pci 0000:00:1f.2: [8086:3b22] type 00 class 0x010601
[ 0.342519] pci 0000:00:1f.2: reg 10: [io 0x1190-0x1197]
[ 0.342524] pci 0000:00:1f.2: reg 14: [io 0x11a8-0x11ab]
[ 0.342530] pci 0000:00:1f.2: reg 18: [io 0x1198-0x119f]
[ 0.342535] pci 0000:00:1f.2: reg 1c: [io 0x11ac-0x11af]
[ 0.342541] pci 0000:00:1f.2: reg 20: [io 0x1120-0x113f]
[ 0.342547] pci 0000:00:1f.2: reg 24: [mem 0xf0426000-0xf04267ff]
[ 0.342580] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.342621] pci 0000:00:1c.0: PCI bridge to [bus 18]
[ 0.342689] pci 0000:00:1c.4: PCI bridge to [bus 24]
[ 0.342759] pci 0000:00:1c.6: PCI bridge to [bus 30]
[ 0.342843] pci 0000:00:1e.0: PCI bridge to [bus 0d] (subtractive decode)
[ 0.342888] pci 0000:00:1e.0: bridge window [mem 0xf8000000-0xfdffffff] (subtractive decode)
[ 0.342889] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.342890] pci 0000:00:1e.0: bridge window [io 0x1000-0x2fff] (subtractive decode)
[ 0.342891] pci 0000:00:1e.0: bridge window [io 0x3000-0x6fff] (subtractive decode)
[ 0.342892] pci 0000:00:1e.0: bridge window [io 0x7000-0xafff] (subtractive decode)
[ 0.342894] pci 0000:00:1e.0: bridge window [io 0xb000-0xffff] (subtractive decode)
[ 0.342895] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.342896] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xf3ffffff] (subtractive decode)
[ 0.342897] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 0.342910] pci_bus 0000:00: on NUMA node 0
[ 0.342912] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.343001] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX1._PRT]
[ 0.343026] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX5._PRT]
[ 0.343048] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX7._PRT]
[ 0.343070] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
[ 0.343150] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20120913/dsfield-211)
[ 0.343227] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880113432668), AE_ALREADY_EXISTS (20120913/psparse-536)
[ 0.343316] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20120913/nspredef-359)
[ 0.343394] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.343455] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.346571] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.346678] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.346787] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.346892] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.346996] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.347101] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.347206] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.347311] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.347453] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.347515] vgaarb: loaded
[ 0.347544] vgaarb: bridge control possible 0000:00:02.0
[ 0.347609] SCSI subsystem initialized
[ 0.347641] ACPI: bus type scsi registered
[ 0.347693] libata version 3.00 loaded.
[ 0.347707] PCI: Using ACPI for IRQ routing
[ 0.348842] PCI: Discovered peer bus 3f
[ 0.348874] PCI: root bus 3f: using default resources
[ 0.348875] PCI: Probing PCI hardware (bus 3f)
[ 0.348888] PCI host bridge to bus 0000:3f
[ 0.348922] pci_bus 0000:3f: root bus resource [io 0x0000-0xffff]
[ 0.348960] pci_bus 0000:3f: root bus resource [mem 0x00000000-0xfffffffff]
[ 0.349000] pci_bus 0000:3f: No busn resource found for root bus, will use [bus 3f-ff]
[ 0.349064] pci 0000:3f:00.0: [8086:2c61] type 00 class 0x060000
[ 0.349077] pci 0000:3f:00.1: [8086:2d01] type 00 class 0x060000
[ 0.349090] pci 0000:3f:02.0: [8086:2d10] type 00 class 0x060000
[ 0.349102] pci 0000:3f:02.1: [8086:2d11] type 00 class 0x060000
[ 0.349113] pci 0000:3f:02.2: [8086:2d12] type 00 class 0x060000
[ 0.349125] pci 0000:3f:02.3: [8086:2d13] type 00 class 0x060000
[ 0.349143] pci_bus 0000:3f: busn_res: [bus 3f-ff] end is updated to 3f
[ 0.349204] PCI: pci_cache_line_size set to 64 bytes
[ 0.349237] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[ 0.349238] e820: reserve RAM buffer [mem 0xdb7ac440-0xdbffffff]
[ 0.349300] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.349375] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.351414] Switching to clocksource hpet
[ 0.351476] pnp: PnP ACPI init
[ 0.351511] ACPI: bus type pnp registered
[ 0.351642] pnp 00:00: [mem 0xf8000000-0xfdffffff window]
[ 0.351643] pnp 00:00: [bus 00-ff]
[ 0.351644] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.351646] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.351647] pnp 00:00: [io 0x1000-0x2fff window]
[ 0.351648] pnp 00:00: [io 0x3000-0x6fff window]
[ 0.351649] pnp 00:00: [io 0x7000-0xafff window]
[ 0.351650] pnp 00:00: [io 0xb000-0xffff window]
[ 0.351651] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.351653] pnp 00:00: [mem 0xe0000000-0xf3ffffff window]
[ 0.351654] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 0.351668] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.351675] pnp 00:01: [io 0x00f0-0x00ff]
[ 0.351681] pnp 00:01: [irq 13]
[ 0.351691] pnp 00:01: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.351697] pnp 00:02: [io 0x0000-0x000f]
[ 0.351698] pnp 00:02: [io 0x0080-0x008f]
[ 0.351699] pnp 00:02: [io 0x00c0-0x00df]
[ 0.351701] pnp 00:02: [dma 4]
[ 0.351709] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.351713] pnp 00:03: [io 0x0070-0x0071]
[ 0.351716] pnp 00:03: [irq 8]
[ 0.351725] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.351730] pnp 00:04: [io 0x0061]
[ 0.351738] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.351745] pnp 00:05: [irq 12]
[ 0.351755] pnp 00:05: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
[ 0.351759] pnp 00:06: [io 0x0060]
[ 0.351760] pnp 00:06: [io 0x0064]
[ 0.351763] pnp 00:06: [irq 1]
[ 0.351774] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.351921] pnp 00:07: [irq 7]
[ 0.351923] pnp 00:07: [dma 3]
[ 0.351924] pnp 00:07: [io 0x0378-0x037f]
[ 0.351925] pnp 00:07: [io 0x0778-0x077d]
[ 0.351960] pnp 00:07: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.352078] pnp 00:08: [irq 4]
[ 0.352079] pnp 00:08: [io 0x03f8-0x03ff]
[ 0.352114] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
[ 0.352142] pnp 00:09: [mem 0xfec00000-0xfec00fff]
[ 0.352152] pnp 00:09: Plug and Play ACPI device, IDs PNP0003 (active)
[ 0.352157] pnp 00:0a: [io 0x004e-0x004f]
[ 0.352158] pnp 00:0a: [io 0x0cb0-0x0cbb]
[ 0.352159] pnp 00:0a: [mem 0xfed40000-0xfed44fff]
[ 0.352169] pnp 00:0a: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 0.352187] pnp 00:0b: [mem 0xfed00000-0xfed003ff]
[ 0.352196] pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.352294] pnp 00:0c: [io 0x0010-0x001f]
[ 0.352295] pnp 00:0c: [io 0x0050-0x0053]
[ 0.352296] pnp 00:0c: [io 0x0072-0x0077]
[ 0.352297] pnp 00:0c: [io 0x0090-0x009f]
[ 0.352314] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.352325] pnp 00:0d: [io 0x04d0-0x04d1]
[ 0.352341] system 00:0d: [io 0x04d0-0x04d1] has been reserved
[ 0.352379] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.352390] pnp 00:0e: [io 0x0400-0x041f]
[ 0.352391] pnp 00:0e: [io 0x0420-0x043f]
[ 0.352392] pnp 00:0e: [io 0x0440-0x045f]
[ 0.352393] pnp 00:0e: [io 0x0460-0x047f]
[ 0.352394] pnp 00:0e: [io 0x0480-0x048f]
[ 0.352395] pnp 00:0e: [io 0xf800-0xf81f]
[ 0.352396] pnp 00:0e: [io 0xf820-0xf83f]
[ 0.352397] pnp 00:0e: [io 0xf840-0xf85f]
[ 0.352398] pnp 00:0e: [io 0xf860-0xf87f]
[ 0.352399] pnp 00:0e: [io 0xfa00-0xfa3f]
[ 0.352401] pnp 00:0e: [io 0xfc00-0xfc7f]
[ 0.352402] pnp 00:0e: [io 0xfc80-0xfcff]
[ 0.352403] pnp 00:0e: [io 0xfe00-0xfe7f]
[ 0.352404] pnp 00:0e: [io 0xfe80-0xfeff]
[ 0.352421] system 00:0e: [io 0x0400-0x041f] has been reserved
[ 0.352459] system 00:0e: [io 0x0420-0x043f] has been reserved
[ 0.352496] system 00:0e: [io 0x0440-0x045f] has been reserved
[ 0.352534] system 00:0e: [io 0x0460-0x047f] has been reserved
[ 0.352571] system 00:0e: [io 0x0480-0x048f] has been reserved
[ 0.352608] system 00:0e: [io 0xf800-0xf81f] has been reserved
[ 0.352646] system 00:0e: [io 0xf820-0xf83f] has been reserved
[ 0.352684] system 00:0e: [io 0xf840-0xf85f] has been reserved
[ 0.352722] system 00:0e: [io 0xf860-0xf87f] has been reserved
[ 0.352759] system 00:0e: [io 0xfa00-0xfa3f] has been reserved
[ 0.352796] system 00:0e: [io 0xfc00-0xfc7f] has been reserved
[ 0.352833] system 00:0e: [io 0xfc80-0xfcff] has been reserved
[ 0.352871] system 00:0e: [io 0xfe00-0xfe7f] has been reserved
[ 0.352908] system 00:0e: [io 0xfe80-0xfeff] has been reserved
[ 0.352946] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.353100] pnp 00:0f: [mem 0x00000000-0x0009ffff]
[ 0.353102] pnp 00:0f: [mem 0x00100000-0xdfffffff]
[ 0.353103] pnp 00:0f: [mem 0x000e4000-0x000fffff]
[ 0.353104] pnp 00:0f: [mem 0xfec01000-0xfecfffff]
[ 0.353105] pnp 00:0f: [mem 0xfed00400-0xfed3ffff]
[ 0.353106] pnp 00:0f: [mem 0xfed45000-0xffffffff]
[ 0.353107] pnp 00:0f: [mem 0xf4000000-0xf7ffffff]
[ 0.353108] pnp 00:0f: [mem 0x000cfe00-0x000e3fff]
[ 0.353130] system 00:0f: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.353170] system 00:0f: [mem 0x00100000-0xdfffffff] could not be reserved
[ 0.353211] system 00:0f: [mem 0x000e4000-0x000fffff] could not be reserved
[ 0.353251] system 00:0f: [mem 0xfec01000-0xfecfffff] has been reserved
[ 0.353290] system 00:0f: [mem 0xfed00400-0xfed3ffff] has been reserved
[ 0.353329] system 00:0f: [mem 0xfed45000-0xffffffff] has been reserved
[ 0.353368] system 00:0f: [mem 0xf4000000-0xf7ffffff] has been reserved
[ 0.353407] system 00:0f: [mem 0x000cfe00-0x000e3fff] has been reserved
[ 0.353447] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.353454] pnp: PnP ACPI: found 16 devices
[ 0.353486] ACPI: ACPI bus type pnp unregistered
[ 0.358488] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 18] add_size 1000
[ 0.358490] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 18] add_size 200000
[ 0.358492] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 18] add_size 200000
[ 0.358498] pci 0000:00:1c.4: bridge window [io 0x1000-0x0fff] to [bus 24] add_size 1000
[ 0.358499] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 24] add_size 200000
[ 0.358501] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff] to [bus 24] add_size 200000
[ 0.358506] pci 0000:00:1c.6: bridge window [io 0x1000-0x0fff] to [bus 30] add_size 1000
[ 0.358508] pci 0000:00:1c.6: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 30] add_size 200000
[ 0.358509] pci 0000:00:1c.6: bridge window [mem 0x00100000-0x000fffff] to [bus 30] add_size 200000
[ 0.358518] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.358519] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.358521] pci 0000:00:1c.4: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.358522] pci 0000:00:1c.4: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.358523] pci 0000:00:1c.6: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.358525] pci 0000:00:1c.6: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.358526] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.358527] pci 0000:00:1c.4: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.358529] pci 0000:00:1c.6: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.358531] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf8000000-0xf81fffff]
[ 0.358572] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.358632] pci 0000:00:1c.4: BAR 14: assigned [mem 0xf8400000-0xf85fffff]
[ 0.358672] pci 0000:00:1c.4: BAR 15: assigned [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.358733] pci 0000:00:1c.6: BAR 14: assigned [mem 0xf8800000-0xf89fffff]
[ 0.358772] pci 0000:00:1c.6: BAR 15: assigned [mem 0xf8a00000-0xf8bfffff 64bit pref]
[ 0.358833] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.358872] pci 0000:00:1c.4: BAR 13: assigned [io 0x3000-0x3fff]
[ 0.358910] pci 0000:00:1c.6: BAR 13: assigned [io 0x4000-0x4fff]
[ 0.358949] pci 0000:00:1c.0: PCI bridge to [bus 18]
[ 0.358985] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.359025] pci 0000:00:1c.0: bridge window [mem 0xf8000000-0xf81fffff]
[ 0.359066] pci 0000:00:1c.0: bridge window [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.359129] pci 0000:00:1c.4: PCI bridge to [bus 24]
[ 0.359164] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
[ 0.359204] pci 0000:00:1c.4: bridge window [mem 0xf8400000-0xf85fffff]
[ 0.359244] pci 0000:00:1c.4: bridge window [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.359307] pci 0000:00:1c.6: PCI bridge to [bus 30]
[ 0.359342] pci 0000:00:1c.6: bridge window [io 0x4000-0x4fff]
[ 0.359382] pci 0000:00:1c.6: bridge window [mem 0xf8800000-0xf89fffff]
[ 0.359423] pci 0000:00:1c.6: bridge window [mem 0xf8a00000-0xf8bfffff 64bit pref]
[ 0.359490] pci 0000:00:1e.0: PCI bridge to [bus 0d]
[ 0.359549] pci 0000:00:1e.0: setting latency timer to 64
[ 0.359551] pci_bus 0000:00: resource 4 [mem 0xf8000000-0xfdffffff]
[ 0.359553] pci_bus 0000:00: resource 5 [io 0x0000-0x0cf7]
[ 0.359554] pci_bus 0000:00: resource 6 [io 0x1000-0x2fff]
[ 0.359555] pci_bus 0000:00: resource 7 [io 0x3000-0x6fff]
[ 0.359556] pci_bus 0000:00: resource 8 [io 0x7000-0xafff]
[ 0.359557] pci_bus 0000:00: resource 9 [io 0xb000-0xffff]
[ 0.359558] pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.359559] pci_bus 0000:00: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 0.359561] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.359562] pci_bus 0000:18: resource 0 [io 0x2000-0x2fff]
[ 0.359563] pci_bus 0000:18: resource 1 [mem 0xf8000000-0xf81fffff]
[ 0.359564] pci_bus 0000:18: resource 2 [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.359565] pci_bus 0000:24: resource 0 [io 0x3000-0x3fff]
[ 0.359566] pci_bus 0000:24: resource 1 [mem 0xf8400000-0xf85fffff]
[ 0.359568] pci_bus 0000:24: resource 2 [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.359569] pci_bus 0000:30: resource 0 [io 0x4000-0x4fff]
[ 0.359570] pci_bus 0000:30: resource 1 [mem 0xf8800000-0xf89fffff]
[ 0.359571] pci_bus 0000:30: resource 2 [mem 0xf8a00000-0xf8bfffff 64bit pref]
[ 0.359572] pci_bus 0000:0d: resource 4 [mem 0xf8000000-0xfdffffff]
[ 0.359573] pci_bus 0000:0d: resource 5 [io 0x0000-0x0cf7]
[ 0.359575] pci_bus 0000:0d: resource 6 [io 0x1000-0x2fff]
[ 0.359576] pci_bus 0000:0d: resource 7 [io 0x3000-0x6fff]
[ 0.359577] pci_bus 0000:0d: resource 8 [io 0x7000-0xafff]
[ 0.359578] pci_bus 0000:0d: resource 9 [io 0xb000-0xffff]
[ 0.359579] pci_bus 0000:0d: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.359580] pci_bus 0000:0d: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 0.359581] pci_bus 0000:0d: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.359583] pci_bus 0000:3f: resource 4 [io 0x0000-0xffff]
[ 0.359584] pci_bus 0000:3f: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.359601] NET: Registered protocol family 2
[ 0.359717] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.360364] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.360584] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.360652] TCP: reno registered
[ 0.360684] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.360731] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.360834] NET: Registered protocol family 1
[ 0.360879] pci 0000:00:02.0: Boot video device
[ 0.360953] PCI: CLS 64 bytes, default 64
[ 0.360969] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.361008] software IO TLB [mem 0xd77aa000-0xdb7a9fff] (64MB) mapped at [ffff8800d77aa000-ffff8800db7a9fff]
[ 0.361421] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.362182] VFS: Disk quotas dquot_6.5.2
[ 0.362239] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.362442] msgmni has been set to 7504
[ 0.362638] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.362698] io scheduler noop registered
[ 0.362731] io scheduler deadline registered
[ 0.362766] io scheduler cfq registered (default)
[ 0.362925] intel_idle: MWAIT substates: 0x1120
[ 0.362926] intel_idle: v0.4 model 0x25
[ 0.362926] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.362989] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.363054] ACPI: Power Button [PBTN]
[ 0.363106] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.363166] ACPI: Power Button [PWRF]
[ 0.363221] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.383614] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.403917] 0000:00:16.3: ttyS1 at I/O 0x1188 (irq = 17) is a 16550A
[ 0.404058] Linux agpgart interface v0.103
[ 0.404116] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset
[ 0.404188] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 0.404893] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[ 0.405007] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 0.405079] [drm] Initialized drm 1.1.0 20060810
[ 0.405223] [drm:i915_dump_device_info], i915 device info: gen=5, pciid=0x0042 flags=need_gfx_hws,has_hotplug,has_bsd_ring,
[ 0.405230] i915 0000:00:02.0: setting latency timer to 64
[ 0.417807] [drm:intel_detect_pch], Found Ibex Peak PCH
[ 0.417854] [drm:intel_opregion_setup], graphic opregion physical addr: 0xdb7ac440
[ 0.417859] [drm:intel_opregion_setup], SWSCI supported
[ 0.417877] i915 0000:00:02.0: irq 40 for MSI/MSI-X
[ 0.417882] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 0.417921] [drm] Driver supports precise vblank timestamp query.
[ 0.417958] [drm:init_vbt_defaults], Set default to SSC at 100MHz
[ 0.417960] [drm:intel_parse_bios], Using VBT from OpRegion: $VBT IRONLAKE-DESK d
[ 0.417962] [drm:parse_general_features], BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 1 lvds_use_ssc 0 lvds_ssc_freq 120 display_clock_mode 0
[ 0.417963] [drm:parse_general_definitions], crt_ddc_bus_pin: 2
[ 0.417966] [drm:parse_lfp_panel_data], Found panel mode in BIOS VBT tables:
[ 0.417967] [drm:drm_mode_debug_printmodeline], Modeline 0:"1024x768" 0 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
[ 0.417969] [drm:parse_lfp_panel_data], VBT initial LVDS value 300
[ 0.417971] [drm:parse_sdvo_panel_data], Found SDVO panel mode in BIOS VBT tables:
[ 0.417972] [drm:drm_mode_debug_printmodeline], Modeline 0:"1600x1200" 0 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x8 0xa
[ 0.417973] [drm:parse_sdvo_device_mapping], No SDVO device info is found in VBT
[ 0.417979] [drm:intel_dsm_pci_probe], no _DSM method for intel device
[ 0.417988] [drm:intel_modeset_init], 2 display pipes available.
[ 0.417996] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 0.418376] [drm:intel_crt_init], pch crt adpa set to 0xf40000
[ 0.418401] [drm:intel_dp_i2c_init], i2c_init DPDDC-C
[ 0.419413] [drm:ironlake_init_pch_refclk], has_panel 0 has_lvds 0 has_pch_edp 0 has_cpu_edp 0 has_ck505 0
[ 0.419416] [drm:ironlake_init_pch_refclk], Disabling SSC entirely
[ 0.421277] [drm:init_status_page], render ring hws offset: 0x00001000
[ 0.421614] [drm:init_status_page], bsd ring hws offset: 0x00025000
[ 0.421943] [drm:intel_modeset_setup_hw_state], [CRTC:3] hw state readout: enabled
[ 0.421944] [drm:intel_modeset_setup_hw_state], [CRTC:5] hw state readout: disabled
[ 0.421946] [drm:intel_modeset_setup_hw_state], [ENCODER:8:DAC-8] hw state readout: disabled, pipe=0
[ 0.421948] [drm:intel_modeset_setup_hw_state], [ENCODER:9:TMDS-9] hw state readout: disabled, pipe=0
[ 0.421950] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 0.421952] [drm:intel_modeset_setup_hw_state], [ENCODER:14:TMDS-14] hw state readout: enabled, pipe=0
[ 0.421954] [drm:intel_modeset_setup_hw_state], [CONNECTOR:7:VGA-1] hw state readout: disabled
[ 0.421955] [drm:intel_modeset_setup_hw_state], [CONNECTOR:10:HDMI-A-1] hw state readout: disabled
[ 0.421957] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 0.421958] [drm:intel_modeset_setup_hw_state], [CONNECTOR:13:DP-1] hw state readout: enabled
[ 0.421962] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 0.421963] [drm:intel_connector_check_state], [CONNECTOR:13:DP-1]
[ 0.421964] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 0.421966] [drm:intel_modeset_check_state], [ENCODER:8:DAC-8]
[ 0.421967] [drm:intel_modeset_check_state], [ENCODER:9:TMDS-9]
[ 0.421969] [drm:intel_modeset_check_state], [ENCODER:14:TMDS-14]
[ 0.421971] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 0.421971] [drm:intel_modeset_check_state], [CRTC:3]
[ 0.421973] [drm:intel_modeset_check_state], [CRTC:5]
[ 0.421994] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 0.421996] [drm:intel_ironlake_crt_detect_hotplug], trigger hotplug detect cycle: adpa=0xf40000
[ 0.435205] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 0.435206] [drm:intel_crt_detect], CRT not detected via hotplug
[ 0.443181] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 0.443183] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 0.443185] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 0.443497] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 0.443498] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 0.443500] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 0.443501] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 0.451158] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 0.451160] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 0.451161] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 0.451162] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:13:DP-1]
[ 0.451467] [drm:intel_dp_detect], DPCD: 1106840100000100
[ 0.452481] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.479181] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.480195] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.498536] [drm:i915_hotplug_work_func], running encoder hotplug functions
[ 0.507489] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.507491] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 209
[ 0.507552] Raw EDID:
[ 0.507581] 00 ff ff ff ff ff ff 00 22 f0 49 29 00 00 00 00
[ 0.507618] 15 15 01 04 a5 33 1d 78 26 01 f5 a2 57 52 9f 27
[ 0.507654] 0a 50 54 a1 08 00 81 c0 81 80 95 00 b3 00 d1 c0
[ 0.507691] 01 01 01 01 01 01 02 3a 80 18 71 38 2d 40 58 2c
[ 0.507727] 45 00 fe 1f 11 00 00 1e 00 00 00 fd 00 32 4c 18
[ 0.507764] 5e 11 00 0a 20 20 20 11 20 00 00 00 fc 00 48 50
[ 0.507801] 20 4c 41 32 33 30 36 0a 20 20 20 00 00 00 ff 00
[ 0.507837] 43 4e 43 31 32 31 31 32 50 42 0a 20 20 00 5a 00
[ 0.530912] ------------[ cut here ]------------
[ 0.530953] WARNING: at drivers/gpu/drm/i915/intel_dp.c:392 intel_dp_aux_ch+0xd4/0x380()
[ 0.531014] Hardware name: HP Compaq 8100 Elite SFF PC
[ 0.531049] dp_aux_ch not started status 0x4025003f
[ 0.531084] Modules linked in:
[ 0.531120] Pid: 6, comm: kworker/u:0 Not tainted 3.7.0-rc7-00113-gcc19528 #75
[ 0.531180] Call Trace:
[ 0.531214] [<ffffffff81036899>] ? warn_slowpath_common+0x79/0xc0
[ 0.531253] [<ffffffff81036995>] ? warn_slowpath_fmt+0x45/0x50
[ 0.531291] [<ffffffff812c5d84>] ? intel_dp_aux_ch+0xd4/0x380
[ 0.531330] [<ffffffff812c60d8>] ? intel_dp_aux_native_read_retry+0xa8/0x130
[ 0.531372] [<ffffffff812c6657>] ? intel_dp_get_dpcd+0x17/0x60
[ 0.531411] [<ffffffff812c7589>] ? intel_dp_hot_plug+0x39/0x180
[ 0.531450] [<ffffffff8129a9de>] ? i915_hotplug_work_func+0x6e/0xa0
[ 0.531490] [<ffffffff8104cc40>] ? process_one_work+0x120/0x430
[ 0.531528] [<ffffffff8129a970>] ? i915_error_work_func+0x100/0x100
[ 0.531569] [<ffffffff8104ee4d>] ? worker_thread+0x15d/0x450
[ 0.531606] [<ffffffff8104ecf0>] ? busy_worker_rebind_fn+0x100/0x100
[ 0.531647] [<ffffffff81053953>] ? kthread+0xb3/0xc0
[ 0.531684] [<ffffffff810538a0>] ? kthread_create_on_node+0x110/0x110
[ 0.531724] [<ffffffff814455ac>] ? ret_from_fork+0x7c/0xb0
[ 0.532258] [<ffffffff810538a0>] ? kthread_create_on_node+0x110/0x110
[ 0.532300] ---[ end trace 385ceeecb2e396ac ]---
[ 0.534584] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.534604] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[ 0.534617] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:13:DP-1] probed modes :
[ 0.534618] [drm:drm_mode_debug_printmodeline], Modeline 16:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.534620] [drm:drm_mode_debug_printmodeline], Modeline 20:"1680x1050" 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6
[ 0.534622] [drm:drm_mode_debug_printmodeline], Modeline 47:"1680x945" 60 131481 1680 1784 1960 2240 945 946 949 978 0x0 0x6
[ 0.534624] [drm:drm_mode_debug_printmodeline], Modeline 42:"1400x1050" 75 156000 1400 1504 1648 1896 1050 1053 1057 1099 0x40 0x6
[ 0.534625] [drm:drm_mode_debug_printmodeline], Modeline 41:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x40 0x6
[ 0.534627] [drm:drm_mode_debug_printmodeline], Modeline 46:"1600x900" 60 118963 1600 1696 1864 2128 900 901 904 932 0x0 0x6
[ 0.534629] [drm:drm_mode_debug_printmodeline], Modeline 39:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 0.534630] [drm:drm_mode_debug_printmodeline], Modeline 18:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 0.534632] [drm:drm_mode_debug_printmodeline], Modeline 43:"1440x900" 75 136750 1440 1536 1688 1936 900 903 909 942 0x40 0x6
[ 0.534634] [drm:drm_mode_debug_printmodeline], Modeline 19:"1440x900" 60 106500 1440 1520 1672 1904 900 903 909 934 0x40 0x6
[ 0.534636] [drm:drm_mode_debug_printmodeline], Modeline 38:"1280x960" 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
[ 0.534637] [drm:drm_mode_debug_printmodeline], Modeline 45:"1366x768" 60 85885 1366 1439 1583 1800 768 769 772 795 0x0 0x6
[ 0.534639] [drm:drm_mode_debug_printmodeline], Modeline 40:"1360x768" 60 85500 1360 1424 1536 1792 768 771 777 795 0x40 0x5
[ 0.534641] [drm:drm_mode_debug_printmodeline], Modeline 37:"1280x800" 75 106500 1280 1360 1488 1696 800 803 809 838 0x40 0x6
[ 0.534643] [drm:drm_mode_debug_printmodeline], Modeline 36:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x9
[ 0.534644] [drm:drm_mode_debug_printmodeline], Modeline 33:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[ 0.534646] [drm:drm_mode_debug_printmodeline], Modeline 35:"1280x768" 75 102250 1280 1360 1488 1696 768 771 778 805 0x40 0x9
[ 0.534648] [drm:drm_mode_debug_printmodeline], Modeline 34:"1280x768" 60 79500 1280 1344 1472 1664 768 771 778 798 0x40 0x6
[ 0.534650] [drm:drm_mode_debug_printmodeline], Modeline 17:"1280x720" 60 74440 1280 1336 1472 1664 720 721 724 746 0x0 0x6
[ 0.534651] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[ 0.534653] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
[ 0.534655] [drm:drm_mode_debug_printmodeline], Modeline 24:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[ 0.534656] [drm:drm_mode_debug_printmodeline], Modeline 44:"1024x576" 60 46970 1024 1064 1168 1312 576 577 580 597 0x0 0x6
[ 0.534658] [drm:drm_mode_debug_printmodeline], Modeline 28:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[ 0.534660] [drm:drm_mode_debug_printmodeline], Modeline 29:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[ 0.534662] [drm:drm_mode_debug_printmodeline], Modeline 21:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[ 0.534663] [drm:drm_mode_debug_printmodeline], Modeline 27:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[ 0.534665] [drm:drm_mode_debug_printmodeline], Modeline 30:"848x480" 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
[ 0.534667] [drm:drm_mode_debug_printmodeline], Modeline 26:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[ 0.534668] [drm:drm_mode_debug_printmodeline], Modeline 25:"640x480" 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
[ 0.534670] [drm:drm_mode_debug_printmodeline], Modeline 22:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[ 0.534672] [drm:drm_mode_debug_printmodeline], Modeline 23:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 0.534674] [drm:drm_setup_crtcs],
[ 0.534675] [drm:drm_enable_connectors], connector 7 enabled? no
[ 0.534676] [drm:drm_enable_connectors], connector 10 enabled? no
[ 0.534677] [drm:drm_enable_connectors], connector 13 enabled? yes
[ 0.534678] [drm:drm_target_preferred], looking for cmdline mode on connector 13
[ 0.534679] [drm:drm_target_preferred], looking for preferred mode on connector 13
[ 0.534680] [drm:drm_target_preferred], found mode 1920x1080
[ 0.534681] [drm:drm_setup_crtcs], picking CRTCs for 8192x8192 config
[ 0.534682] [drm:drm_setup_crtcs], desired mode 1920x1080 set on crtc 3
[ 0.539626] [drm:intel_dp_check_link_status], TMDS-14: channel EQ not ok, retraining
[ 0.539839] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.540552] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.547271] [drm:intelfb_create], allocated 1920x1080 fb: 0x00047000, bo ffff880112a24c00
[ 0.547311] fbcon: inteldrmfb (fb0) is primary device
[ 0.547603] [drm:intel_dp_link_down],
[ 0.574979] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.575687] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.582720] [drm:intel_dp_link_down],
[ 0.606881] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.607589] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.614621] [drm:intel_dp_link_down],
[ 0.638784] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.639492] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.646524] [drm:intel_dp_link_down],
[ 0.670687] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.671395] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.678427] [drm:intel_dp_link_down],
[ 0.702589] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.703298] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.710330] [drm:intel_dp_link_down],
[ 0.734492] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.735200] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.735201] [drm:intel_dp_complete_link_train] *ERROR* failed to train DP, aborting
[ 0.735202] [drm:intel_dp_link_down],
[ 0.762413] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 0.762414] [drm:intel_set_config_compute_mode_changes], crtc has no fb, full mode set
[ 0.762415] [drm:intel_set_config_compute_mode_changes], modes are different, full mode set
[ 0.762417] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
[ 0.762419] [drm:drm_mode_debug_printmodeline], Modeline 48:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.762420] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 0.762421] [drm:intel_crtc_set_config], attempting to set mode from userspace
[ 0.762422] [drm:drm_mode_debug_printmodeline], Modeline 48:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.762424] [drm:intel_set_mode], set mode pipe masks: modeset: 1, prepare: 1, disable: 0
[ 0.762426] [drm:intel_dp_mode_fixup], DP link computation with max lane count 4 max bw 06 pixel clock 148500KHz
[ 0.762427] [drm:intel_dp_mode_fixup], DP link bw 06 lane count 4 clock 162000 bpp 24
[ 0.762427] [drm:intel_dp_mode_fixup], DP link bw required 356400 available 518400
[ 0.762428] [drm:intel_modeset_adjusted_mode], [CRTC:3]
[ 0.762632] [drm:intel_dp_link_down],
[ 0.893805] ------------[ cut here ]------------
[ 0.893810] WARNING: at drivers/gpu/drm/i915/intel_display.c:1009 ironlake_crtc_disable+0xaf/0x8e0()
[ 0.893811] Hardware name: HP Compaq 8100 Elite SFF PC
[ 0.893811] pipe_off wait timed out
[ 0.893812] Modules linked in:
[ 0.893813] Pid: 1, comm: swapper/0 Tainted: G W 3.7.0-rc7-00113-gcc19528 #75
[ 0.893813] Call Trace:
[ 0.893818] [<ffffffff81036899>] ? warn_slowpath_common+0x79/0xc0
[ 0.893819] [<ffffffff81036995>] ? warn_slowpath_fmt+0x45/0x50
[ 0.893820] [<ffffffff812b5ceb>] ? intel_wait_for_pipe_off+0x5b/0x170
[ 0.893821] [<ffffffff812b669f>] ? ironlake_crtc_disable+0xaf/0x8e0
[ 0.893823] [<ffffffff81281294>] ? drm_ut_debug_printk+0x44/0x70
[ 0.893825] [<ffffffff812bd4c6>] ? intel_set_mode+0x306/0x920
[ 0.893827] [<ffffffff812be1d1>] ? intel_crtc_set_config+0x6f1/0x950
[ 0.893830] [<ffffffff81442f61>] ? __mutex_lock_slowpath+0xd1/0x140
[ 0.893833] [<ffffffff8127545f>] ? drm_fb_helper_set_par+0x6f/0xe0
[ 0.893836] [<ffffffff8120c7bf>] ? fbcon_init+0x55f/0x5f0
[ 0.893838] [<ffffffff8125af8c>] ? visual_init+0xac/0x110
[ 0.893839] [<ffffffff8125c7ec>] ? bind_con_driver+0x16c/0x340
[ 0.893841] [<ffffffff8125ca20>] ? take_over_console+0x60/0x70
[ 0.893842] [<ffffffff8120ab6b>] ? fbcon_takeover+0x5b/0xc0
[ 0.893845] [<ffffffff81059375>] ? notifier_call_chain+0x45/0x60
[ 0.893846] [<ffffffff81059555>] ? __blocking_notifier_call_chain+0x55/0x80
[ 0.893847] [<ffffffff8120415f>] ? register_framebuffer+0x1af/0x2e0
[ 0.893849] [<ffffffff812756c4>] ? drm_fb_helper_single_fb_probe+0x1f4/0x320
[ 0.893850] [<ffffffff81275999>] ? drm_fb_helper_initial_config+0x1a9/0x220
[ 0.893853] [<ffffffff810dd13d>] ? __kmalloc+0xed/0x130
[ 0.893856] [<ffffffff812d6ead>] ? intel_fbdev_init+0x7d/0xb0
[ 0.893857] [<ffffffff81298e55>] ? i915_driver_load+0xd95/0xf00
[ 0.893859] [<ffffffff81283fa5>] ? drm_get_pci_dev+0x185/0x2c0
[ 0.893861] [<ffffffff811f3d41>] ? pci_device_probe+0xd1/0x170
[ 0.893862] [<ffffffff812e9ed8>] ? driver_probe_device+0x68/0x220
[ 0.893863] [<ffffffff812ea123>] ? __driver_attach+0x93/0xa0
[ 0.893864] [<ffffffff812ea090>] ? driver_probe_device+0x220/0x220
[ 0.893865] [<ffffffff812e836d>] ? bus_for_each_dev+0x4d/0x80
[ 0.893866] [<ffffffff812e9648>] ? bus_add_driver+0x178/0x260
[ 0.893867] [<ffffffff812ea724>] ? driver_register+0x84/0x180
[ 0.893869] [<ffffffff8188c7c4>] ? drm_core_init+0x12f/0x12f
[ 0.893871] [<ffffffff810002e2>] ? do_one_initcall+0x122/0x170
[ 0.893872] [<ffffffff8142c6bc>] ? kernel_init+0x11c/0x2a0
[ 0.893874] [<ffffffff8186c54a>] ? do_early_param+0x83/0x83
[ 0.893876] [<ffffffff8105e761>] ? schedule_tail+0x21/0xb0
[ 0.893877] [<ffffffff8142c5a0>] ? rest_init+0x70/0x70
[ 0.893878] [<ffffffff814455ac>] ? ret_from_fork+0x7c/0xb0
[ 0.893879] [<ffffffff8142c5a0>] ? rest_init+0x70/0x70
[ 0.893880] ---[ end trace 385ceeecb2e396ad ]---
[ 0.949634] [drm:intel_disable_transcoder] *ERROR* failed to disable transcoder 0
[ 0.949840] [drm:intel_choose_pipe_bpp_dither], clamping display bpc (was -1) to EDID reported max of 8
[ 0.949841] [drm:intel_choose_pipe_bpp_dither], setting pipe bpc to 8 (max display bpc 8)
[ 0.949842] [drm:ironlake_crtc_mode_set], Mode for pipe 0:
[ 0.949844] [drm:drm_mode_debug_printmodeline], Modeline 48:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.949845] [drm:intel_get_pch_pll], CRTC:3 using pre-allocated PCH PLL c6014
[ 0.949845] [drm:intel_get_pch_pll], using pll 0 for pipe 0
[ 0.949846] [drm:intel_get_pch_pll], switching PLL c6014 off
[ 1.005465] [drm:ironlake_wait_for_vblank], vblank wait timed out
[ 1.005468] [drm:ironlake_update_plane], Writing base 00047000 00000000 0 0 7680
[ 1.005470] [drm:ironlake_update_wm], FIFO watermarks For pipe A - plane 9, cursor: 6
[ 1.005471] [drm:ironlake_check_srwm], watermark 1: display plane 91, fbc lines 3, cursor 6
[ 1.005472] [drm:ironlake_check_srwm], watermark 2: display plane 202, fbc lines 4, cursor 10
[ 1.005474] [drm:intel_set_mode], [ENCODER:14:TMDS-14] set [MODE:48:1920x1080]
[ 1.005475] [drm:ironlake_update_wm], FIFO watermarks For pipe A - plane 9, cursor: 6
[ 1.005477] [drm:ironlake_check_srwm], watermark 1: display plane 91, fbc lines 3, cursor 6
[ 1.005478] [drm:ironlake_check_srwm], watermark 2: display plane 202, fbc lines 4, cursor 10
[ 1.061295] [drm:ironlake_wait_for_vblank], vblank wait timed out
[ 1.117125] [drm:ironlake_wait_for_vblank], vblank wait timed out
[ 1.117428] [drm:ironlake_fdi_link_train], FDI_RX_IIR 0x700
[ 1.117429] [drm:ironlake_fdi_link_train], FDI train 1 done.
[ 1.117581] [drm:ironlake_fdi_link_train], FDI_RX_IIR 0x600
[ 1.117582] [drm:ironlake_fdi_link_train], FDI train 2 done.
[ 1.117582] [drm:ironlake_fdi_link_train], FDI train done
[ 1.117583] [drm:intel_enable_pch_pll], enable PCH PLL c6014 (active 0, on? 0)for crtc 3
[ 1.117584] [drm:intel_enable_pch_pll], enabling PCH PLL c6014
[ 1.117826] [drm:intel_prepare_page_flip], preparing flip with no unpin work?
[ 1.119191] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.119900] [drm:intel_dp_start_link_train], training pattern 1 signal levels 02000000
[ 1.120609] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.121318] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.122027] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.122735] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.123444] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.124153] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.124862] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.126071] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.126780] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.127489] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.128198] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.128907] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.129616] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.130324] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.131033] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.131742] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.132451] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.133160] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.133869] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.135078] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.135787] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.136496] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.137205] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.137913] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.138622] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.139331] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.140040] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.140749] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.141458] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.142166] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.142875] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.144084] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.144793] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.145502] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.146211] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.146920] [drm:intel_dp_start_link_train], training pattern 1 signal levels 02000000
[ 1.147629] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.148338] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.149047] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.149755] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.150464] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.151173] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.151882] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.153091] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.153800] [drm:intel_dp_start_link_train], clock recovery OK
[ 1.176945] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 1.176946] [drm:intel_connector_check_state], [CONNECTOR:13:DP-1]
[ 1.176947] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 1.176948] [drm:intel_modeset_check_state], [ENCODER:8:DAC-8]
[ 1.176949] [drm:intel_modeset_check_state], [ENCODER:9:TMDS-9]
[ 1.176951] [drm:intel_modeset_check_state], [ENCODER:14:TMDS-14]
[ 1.176952] [drm:intel_dp_get_hw_state], No pipe for dp port 0xe4200 found
[ 1.176952] [drm:intel_modeset_check_state], [CRTC:3]
[ 1.176953] [drm:intel_modeset_check_state], [CRTC:5]
[ 1.176954] [drm:intel_crtc_set_config], [CRTC:5] [NOFB]
[ 1.176955] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 1.176974] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 1.176975] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 1.180798] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 1.180799] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 1.184608] Console: switching to colour frame buffer device 240x67
[ 1.184610] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 1.184611] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 1.197348] fb0: inteldrmfb frame buffer device
[ 1.198501] drm: registered panic notifier
[ 1.199692] ACPI Exception: AE_NOT_FOUND, Evaluating _DOD (20120913/video-1149)
[ 1.200878] ACPI: Video Device [GFX0] (multi-head: no rom: yes post: no)
[ 1.202081] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input2
[ 1.203280] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 1.204531] ahci 0000:00:1f.2: version 3.0
[ 1.204571] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 1.204618] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x17 impl SATA mode
[ 1.205838] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part sxs apst
[ 1.207062] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.207370] scsi0 : ahci
[ 1.208646] scsi1 : ahci
[ 1.209900] scsi2 : ahci
[ 1.211148] scsi3 : ahci
[ 1.212385] scsi4 : ahci
[ 1.213622] scsi5 : ahci
[ 1.214835] ata1: SATA max UDMA/133 abar m2048@0xf0426000 port 0xf0426100 irq 41
[ 1.216056] ata2: SATA max UDMA/133 abar m2048@0xf0426000 port 0xf0426180 irq 41
[ 1.217273] ata3: SATA max UDMA/133 abar m2048@0xf0426000 port 0xf0426200 irq 41
[ 1.218482] ata4: DUMMY
[ 1.219686] ata5: SATA max UDMA/133 abar m2048@0xf0426000 port 0xf0426300 irq 41
[ 1.220915] ata6: DUMMY
[ 1.222171] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 1.226175] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.227419] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.228704] mousedev: PS/2 mouse device common for all mice
[ 1.229957] rtc_cmos 00:03: RTC can wake from S4
[ 1.231255] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.232493] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.233760] cpuidle: using governor ladder
[ 1.235032] cpuidle: using governor menu
[ 1.236323] TCP: cubic registered
[ 1.237610] NET: Registered protocol family 10
[ 1.238933] mip6: Mobile IPv6
[ 1.240158] NET: Registered protocol family 17
[ 1.241414] Key type dns_resolver registered
[ 1.242735] PM: Hibernation image not present or could not be loaded.
[ 1.242741] registered taskstats version 1
[ 1.244235] rtc_cmos 00:03: setting system clock to 2012-12-01 09:53:33 UTC (1354355613)
[ 1.356467] tsc: Refined TSC clocksource calibration: 3325.374 MHz
[ 1.357792] Switching to clocksource tsc
[ 1.539914] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.541767] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.543070] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.544878] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.546255] ata2.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.548043] ata2.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.549816] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.551578] ata2.00: ATAPI: hp CDDVDW TS-H653T, H6D1, max UDMA/100
[ 1.553445] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.555184] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.557220] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 1.557434] ata1.00: ACPI cmd e3/00:00:00:00:00:a0 (IDLE) succeeded
[ 1.557439] ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.558803] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.560111] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.561484] ata2.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.563064] ata2.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.564895] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.566676] ata2.00: configured for UDMA/100
[ 1.568701] ata1.00: ATA-8: Hitachi HDS721025CLA682, JP1OA41A, max UDMA/133
[ 1.570626] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.572639] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.573769] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.575116] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.576703] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 1.576912] ata1.00: ACPI cmd e3/00:00:00:00:00:a0 (IDLE) succeeded
[ 1.576918] ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.578334] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.579697] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.582300] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.582306] ata1.00: configured for UDMA/133
[ 1.583982] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72102 JP1O PQ: 0 ANSI: 5
[ 1.585531] ACPI: Invalid Power Resource to register!
[ 1.585559] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.587077] scsi 1:0:0:0: CD-ROM hp CDDVDW TS-H653T H6D1 PQ: 0 ANSI: 5
[ 1.587095] sd 0:0:0:0: [sda] Write Protect is off
[ 1.587097] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.587108] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.633167] sda: sda1 sda2 < sda5 >
[ 1.634776] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.708120] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 1.709553] VFS: Mounted root (ext4 filesystem) readonly on device 8:1.
[ 1.711450] Freeing unused kernel memory: 492k freed
[ 1.712926] Write protecting the kernel read-only data: 8192k
[ 1.717138] Freeing unused kernel memory: 1744k freed
[ 1.719905] Freeing unused kernel memory: 688k freed
[ 4.621594] microcode: CPU0 sig=0x20655, pf=0x2, revision=0x2
[ 4.627766] ACPI: Invalid PBLK length [7]
[ 4.629294] ACPI: Requesting acpi_cpufreq
[ 4.630946] ACPI: Invalid PBLK length [7]
[ 4.632483] ACPI: Invalid PBLK length [7]
[ 4.633892] ACPI: Invalid PBLK length [7]
[ 4.694191] microcode: CPU0 updated to revision 0x3, date = 2011-09-01
[ 4.695625] microcode: CPU1 sig=0x20655, pf=0x2, revision=0x2
[ 4.697544] microcode: CPU1 updated to revision 0x3, date = 2011-09-01
[ 4.699355] microcode: CPU2 sig=0x20655, pf=0x2, revision=0x2
[ 4.700873] microcode: CPU2 updated to revision 0x3, date = 2011-09-01
[ 4.702263] microcode: CPU3 sig=0x20655, pf=0x2, revision=0x2
[ 4.703770] microcode: CPU3 updated to revision 0x3, date = 2011-09-01
[ 4.705174] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 4.901502] tpm_tis 00:0a: 1.2 TPM (device-id 0xB, rev-id 16)
[ 5.031431] wmi: Mapper loaded
[ 5.076068] mei 0000:00:16.0: setting latency timer to 64
[ 5.076123] mei 0000:00:16.0: irq 42 for MSI/MSI-X
[ 5.079129] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
[ 5.080608] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 5.082068] e1000e 0000:00:19.0: setting latency timer to 64
[ 5.082108] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 5.083591] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 5.106091] ACPI: bus type usb registered
[ 5.107557] usbcore: registered new interface driver usbfs
[ 5.109021] usbcore: registered new interface driver hub
[ 5.110509] usbcore: registered new device driver usb
[ 5.152890] tpm_tis 00:0a: TPM is disabled/deactivated (0x7)
[ 5.154398] parport_pc 00:07: reported by Plug and Play ACPI
[ 1.591444] ACPI: Invalid Power Resource to register!
[ 5.155886] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 5.196183] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.274246] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 78:e3:b5:a0:e5:e4
[ 5.275643] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 5.277129] e1000e 0000:00:19.0 eth0: MAC: 9, PHY: 9, PBA No: A002FF-0FF
[ 5.278630] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 5.278634] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 5.280084] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 5.285385] ehci_hcd 0000:00:1a.0: debug port 2
[ 5.286789] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 5.286808] ehci_hcd 0000:00:1a.0: irq 20, io mem 0xf0426800
[ 5.296467] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 5.298013] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.299409] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.300860] usb usb1: Product: EHCI Host Controller
[ 5.302266] usb usb1: Manufacturer: Linux 3.7.0-rc7-00113-gcc19528 ehci_hcd
[ 5.303658] usb usb1: SerialNumber: 0000:00:1a.0
[ 5.305183] hub 1-0:1.0: USB hub found
[ 5.306572] hub 1-0:1.0: 3 ports detected
[ 5.308074] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 5.308077] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 5.309518] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 5.314820] ehci_hcd 0000:00:1d.0: debug port 2
[ 5.316217] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 5.316223] ehci_hcd 0000:00:1d.0: irq 20, io mem 0xf0426c00
[ 5.321071] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.322526] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.323944] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 5.326339] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 5.328302] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 5.329817] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.331192] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.332597] usb usb2: Product: EHCI Host Controller
[ 5.333917] usb usb2: Manufacturer: Linux 3.7.0-rc7-00113-gcc19528 ehci_hcd
[ 5.335226] usb usb2: SerialNumber: 0000:00:1d.0
[ 5.336662] hub 2-0:1.0: USB hub found
[ 5.337954] hub 2-0:1.0: 3 ports detected
[ 5.372805] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.374209] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.443426] iTCO_vendor_support: vendor-support=0
[ 5.451660] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 5.453726] iTCO_wdt: Found a Q57 TCO device (Version=2, TCOBASE=0xf860)
[ 5.455110] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.473811] gpio_ich: GPIO from 180 to 255 on gpio_ich
[ 5.615504] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 5.747530] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[ 5.749501] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.751635] hub 1-1:1.0: USB hub found
[ 5.753720] hub 1-1:1.0: 6 ports detected
[ 5.866710] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[ 5.998744] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[ 6.000103] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 6.002038] hub 2-1:1.0: USB hub found
[ 6.004430] hub 2-1:1.0: 8 ports detected
[ 6.078117] usb 1-1.1: new high-speed USB device number 3 using ehci_hcd
[ 6.110677] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 6.112435] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround
[ 6.170245] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2512
[ 6.172289] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 6.174623] hub 1-1.1:1.0: USB hub found
[ 6.176200] hub 1-1.1:1.0: 2 ports detected
[ 6.204166] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 6.249760] usb 1-1.2: new low-speed USB device number 4 using ehci_hcd
[ 6.371236] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c30e
[ 6.373293] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.375285] usb 1-1.2: Product: HID compliant keyboard
[ 6.377345] usb 1-1.2: Manufacturer: Logitech
[ 6.568590] usbcore: registered new interface driver usbhid
[ 6.571382] usbhid: USB HID core driver
[ 6.607495] input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input5
[ 6.608901] hid-generic 0003:046D:C30E.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:1a.0-1.2/input0
[ 6.612874] input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input6
[ 6.614495] hid-generic 0003:046D:C30E.0002: input,hidraw1: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:1a.0-1.2/input1
[ 8.402016] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 8.405207] input: HDA Intel MID Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 8.408347] input: HDA Intel MID Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 8.411490] input: HDA Intel MID Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 8.414633] input: HDA Intel MID Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 9.437311] Adding 7532540k swap on /dev/sda5. Priority:-1 extents:1 across:7532540k
[ 9.465423] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 9.670962] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 10.060071] fuse init (API version 7.20)
[ 10.094613] loop: module loaded
[ 11.174549] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 11.174554] [drm:intel_crt_detect], CRT not detected via hotplug
[ 11.182507] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 11.182514] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 11.182517] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 11.182837] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 11.182839] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 11.182843] [drm:output_poll_execute], [CONNECTOR:7:VGA-1] status updated from 2 to 2
[ 11.190469] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 11.190475] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 11.190478] [drm:output_poll_execute], [CONNECTOR:10:HDMI-A-1] status updated from 2 to 2
[ 11.190787] [drm:intel_dp_detect], DPCD: 1106840100000100
[ 11.191805] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 11.218398] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 11.218408] [drm:output_poll_execute], [CONNECTOR:13:DP-1] status updated from 1 to 1
[ 14.041369] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 14.141561] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 14.141717] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.772885] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 14.772890] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 17.436611] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.443395] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.381685] lp0: using parport0 (interrupt-driven).
[ 22.213998] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 22.214003] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 22.255242] [drm:i915_driver_open],
[ 22.255264] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 22.255268] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 22.255269] [drm:intel_crtc_set_config], [CRTC:5] [NOFB]
[ 22.255270] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 22.255285] [drm:i915_driver_open],
[ 22.330547] [drm:drm_mode_getresources], CRTC[2] CONNECTORS[3] ENCODERS[3]
[ 22.330555] [drm:drm_mode_getresources], CRTC[2] CONNECTORS[3] ENCODERS[3]
[ 22.330599] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 22.330602] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 22.330605] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 22.330607] [drm:intel_crt_detect], CRT not detected via hotplug
[ 22.336258] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 22.336264] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.336267] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 22.336587] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.336588] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 22.336592] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 22.336597] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 22.336599] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 22.336602] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 22.336603] [drm:intel_crt_detect], CRT not detected via hotplug
[ 22.344234] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 22.344241] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.344244] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 22.344563] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.344564] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 22.344567] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 22.344604] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 22.344608] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 22.352238] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 22.352245] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 22.352249] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 22.352257] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 22.352260] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 22.360183] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 22.360188] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 22.360191] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 22.360241] [drm:drm_mode_getconnector], [CONNECTOR:13:?]
[ 22.360245] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:13:DP-1]
[ 22.360556] [drm:intel_dp_detect], DPCD: 1106840100000100
[ 22.361572] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.388340] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.389364] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.415996] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.416043] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[ 22.416085] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:13:DP-1] probed modes :
[ 22.416088] [drm:drm_mode_debug_printmodeline], Modeline 16:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 22.416093] [drm:drm_mode_debug_printmodeline], Modeline 20:"1680x1050" 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6
[ 22.416098] [drm:drm_mode_debug_printmodeline], Modeline 47:"1680x945" 60 131481 1680 1784 1960 2240 945 946 949 978 0x0 0x6
[ 22.416103] [drm:drm_mode_debug_printmodeline], Modeline 42:"1400x1050" 75 156000 1400 1504 1648 1896 1050 1053 1057 1099 0x40 0x6
[ 22.416108] [drm:drm_mode_debug_printmodeline], Modeline 41:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x40 0x6
[ 22.416113] [drm:drm_mode_debug_printmodeline], Modeline 46:"1600x900" 60 118963 1600 1696 1864 2128 900 901 904 932 0x0 0x6
[ 22.416117] [drm:drm_mode_debug_printmodeline], Modeline 39:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 22.416122] [drm:drm_mode_debug_printmodeline], Modeline 18:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 22.416127] [drm:drm_mode_debug_printmodeline], Modeline 43:"1440x900" 75 136750 1440 1536 1688 1936 900 903 909 942 0x40 0x6
[ 22.416132] [drm:drm_mode_debug_printmodeline], Modeline 19:"1440x900" 60 106500 1440 1520 1672 1904 900 903 909 934 0x40 0x6
[ 22.416136] [drm:drm_mode_debug_printmodeline], Modeline 38:"1280x960" 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
[ 22.416141] [drm:drm_mode_debug_printmodeline], Modeline 45:"1366x768" 60 85885 1366 1439 1583 1800 768 769 772 795 0x0 0x6
[ 22.416146] [drm:drm_mode_debug_printmodeline], Modeline 40:"1360x768" 60 85500 1360 1424 1536 1792 768 771 777 795 0x40 0x5
[ 22.416151] [drm:drm_mode_debug_printmodeline], Modeline 37:"1280x800" 75 106500 1280 1360 1488 1696 800 803 809 838 0x40 0x6
[ 22.416156] [drm:drm_mode_debug_printmodeline], Modeline 36:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x9
[ 22.416161] [drm:drm_mode_debug_printmodeline], Modeline 33:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[ 22.416165] [drm:drm_mode_debug_printmodeline], Modeline 35:"1280x768" 75 102250 1280 1360 1488 1696 768 771 778 805 0x40 0x9
[ 22.416170] [drm:drm_mode_debug_printmodeline], Modeline 34:"1280x768" 60 79500 1280 1344 1472 1664 768 771 778 798 0x40 0x6
[ 22.416175] [drm:drm_mode_debug_printmodeline], Modeline 17:"1280x720" 60 74440 1280 1336 1472 1664 720 721 724 746 0x0 0x6
[ 22.416180] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[ 22.416185] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
[ 22.416190] [drm:drm_mode_debug_printmodeline], Modeline 24:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[ 22.416195] [drm:drm_mode_debug_printmodeline], Modeline 44:"1024x576" 60 46970 1024 1064 1168 1312 576 577 580 597 0x0 0x6
[ 22.416199] [drm:drm_mode_debug_printmodeline], Modeline 28:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[ 22.416204] [drm:drm_mode_debug_printmodeline], Modeline 29:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[ 22.416209] [drm:drm_mode_debug_printmodeline], Modeline 21:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[ 22.416213] [drm:drm_mode_debug_printmodeline], Modeline 27:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[ 22.416218] [drm:drm_mode_debug_printmodeline], Modeline 30:"848x480" 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
[ 22.416223] [drm:drm_mode_debug_printmodeline], Modeline 26:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[ 22.416228] [drm:drm_mode_debug_printmodeline], Modeline 25:"640x480" 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
[ 22.416232] [drm:drm_mode_debug_printmodeline], Modeline 22:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[ 22.416237] [drm:drm_mode_debug_printmodeline], Modeline 23:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 22.416252] [drm:drm_mode_getconnector], [CONNECTOR:13:?]
[ 22.416319] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 22.416323] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 22.416327] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 22.416330] [drm:intel_crt_detect], CRT not detected via hotplug
[ 22.424008] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 22.424015] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.424018] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 22.424337] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.424338] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 22.424340] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 22.424344] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 22.424345] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 22.424347] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 22.424349] [drm:intel_crt_detect], CRT not detected via hotplug
[ 22.431963] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 22.431968] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.431971] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 22.432288] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 22.432290] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 22.432291] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 22.432336] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 22.432338] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 22.439935] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 22.439940] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 22.439944] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 22.439950] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 22.439954] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 22.447916] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 22.447923] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 22.447929] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 22.447976] [drm:drm_mode_getconnector], [CONNECTOR:13:?]
[ 22.447980] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:13:DP-1]
[ 22.448288] [drm:intel_dp_detect], DPCD: 1106840100000100
[ 22.449301] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.476072] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.477096] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.503850] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 22.503941] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[ 22.503987] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:13:DP-1] probed modes :
[ 22.503990] [drm:drm_mode_debug_printmodeline], Modeline 16:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 22.503996] [drm:drm_mode_debug_printmodeline], Modeline 20:"1680x1050" 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6
[ 22.504001] [drm:drm_mode_debug_printmodeline], Modeline 47:"1680x945" 60 131481 1680 1784 1960 2240 945 946 949 978 0x0 0x6
[ 22.504006] [drm:drm_mode_debug_printmodeline], Modeline 42:"1400x1050" 75 156000 1400 1504 1648 1896 1050 1053 1057 1099 0x40 0x6
[ 22.504011] [drm:drm_mode_debug_printmodeline], Modeline 41:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x40 0x6
[ 22.504016] [drm:drm_mode_debug_printmodeline], Modeline 46:"1600x900" 60 118963 1600 1696 1864 2128 900 901 904 932 0x0 0x6
[ 22.504021] [drm:drm_mode_debug_printmodeline], Modeline 39:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 22.504025] [drm:drm_mode_debug_printmodeline], Modeline 18:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 22.504030] [drm:drm_mode_debug_printmodeline], Modeline 43:"1440x900" 75 136750 1440 1536 1688 1936 900 903 909 942 0x40 0x6
[ 22.504035] [drm:drm_mode_debug_printmodeline], Modeline 19:"1440x900" 60 106500 1440 1520 1672 1904 900 903 909 934 0x40 0x6
[ 22.504042] [drm:drm_mode_debug_printmodeline], Modeline 38:"1280x960" 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
[ 22.504044] [drm:drm_mode_debug_printmodeline], Modeline 45:"1366x768" 60 85885 1366 1439 1583 1800 768 769 772 795 0x0 0x6
[ 22.504045] [drm:drm_mode_debug_printmodeline], Modeline 40:"1360x768" 60 85500 1360 1424 1536 1792 768 771 777 795 0x40 0x5
[ 22.504047] [drm:drm_mode_debug_printmodeline], Modeline 37:"1280x800" 75 106500 1280 1360 1488 1696 800 803 809 838 0x40 0x6
[ 22.504049] [drm:drm_mode_debug_printmodeline], Modeline 36:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x9
[ 22.504050] [drm:drm_mode_debug_printmodeline], Modeline 33:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[ 22.504052] [drm:drm_mode_debug_printmodeline], Modeline 35:"1280x768" 75 102250 1280 1360 1488 1696 768 771 778 805 0x40 0x9
[ 22.504054] [drm:drm_mode_debug_printmodeline], Modeline 34:"1280x768" 60 79500 1280 1344 1472 1664 768 771 778 798 0x40 0x6
[ 22.504055] [drm:drm_mode_debug_printmodeline], Modeline 17:"1280x720" 60 74440 1280 1336 1472 1664 720 721 724 746 0x0 0x6
[ 22.504057] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[ 22.504059] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
[ 22.504060] [drm:drm_mode_debug_printmodeline], Modeline 24:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[ 22.504062] [drm:drm_mode_debug_printmodeline], Modeline 44:"1024x576" 60 46970 1024 1064 1168 1312 576 577 580 597 0x0 0x6
[ 22.504064] [drm:drm_mode_debug_printmodeline], Modeline 28:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[ 22.504065] [drm:drm_mode_debug_printmodeline], Modeline 29:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[ 22.504067] [drm:drm_mode_debug_printmodeline], Modeline 21:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[ 22.504069] [drm:drm_mode_debug_printmodeline], Modeline 27:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[ 22.504070] [drm:drm_mode_debug_printmodeline], Modeline 30:"848x480" 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
[ 22.504072] [drm:drm_mode_debug_printmodeline], Modeline 26:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[ 22.504073] [drm:drm_mode_debug_printmodeline], Modeline 25:"640x480" 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
[ 22.504075] [drm:drm_mode_debug_printmodeline], Modeline 22:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[ 22.504077] [drm:drm_mode_debug_printmodeline], Modeline 23:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 22.504086] [drm:drm_mode_getconnector], [CONNECTOR:13:?]
[ 22.637439] [drm:drm_mode_addfb], [FB:50]
[ 22.637527] [drm:drm_mode_setcrtc], [CRTC:3]
[ 22.637531] [drm:drm_mode_setcrtc], [CONNECTOR:13:DP-1]
[ 22.637533] [drm:intel_crtc_set_config], [CRTC:3] [FB:50] #connectors=1 (x y) (0 0)
[ 22.637538] [drm:intel_modeset_stage_output_state], [CONNECTOR:13:DP-1] to [CRTC:3]
[ 22.649174] [drm:ironlake_update_plane], Writing base 00830000 00000000 0 0 7680
[ 22.655092] [drm:intel_prepare_page_flip], preparing flip with no unpin work?
[ 32.325164] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 32.325172] [drm:intel_crt_detect], CRT not detected via hotplug
[ 32.333135] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 32.333140] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 32.333143] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 32.333458] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 32.333460] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 32.333462] [drm:output_poll_execute], [CONNECTOR:7:VGA-1] status updated from 2 to 2
[ 32.341105] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 32.341111] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 32.341115] [drm:output_poll_execute], [CONNECTOR:10:HDMI-A-1] status updated from 2 to 2
[ 32.341423] [drm:intel_dp_detect], DPCD: 1106840100000100
[ 32.342439] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 32.369257] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 32.369261] [drm:output_poll_execute], [CONNECTOR:13:DP-1] status updated from 1 to 1

--
Meelis Roos (mroos@linux.ee)


\
 
 \ /
  Last update: 2012-12-01 11:41    [W:0.142 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site