lkml.org 
[lkml]   [2012]   [Nov]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/3] omap: craneboard: support the TPS65910 PMU
Date

This patch supports the TPS65910 PMU function on the AM3517 Craneboard.
The IRQ pin, SYS_NIRQ is dedicated connection between the AM3517 and
the TPS65910 PMU.
To handle the PMU IRQs, mux configuration is required.

Platform data configuration:
.IRQ number : SYS_NIRQ (M_IRQ_7)
.External clock source : external 32KHz clock is connected

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
---
arch/arm/mach-omap2/board-am3517crane.c | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)

diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 37646e5..82805de 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -20,6 +20,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/gpio.h>
+#include <linux/mfd/tps65910.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
@@ -41,6 +42,7 @@

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
@@ -86,6 +88,24 @@ static struct mtd_partition crane_nand_partitions[] = {
},
};

+static struct tps65910_board tps65910_pdata = {
+ .irq = 7 + OMAP_INTC_START,
+ .en_ck32k_xtal = true,
+};
+
+static struct i2c_board_info __initdata tps65910_board_info[] = {
+ {
+ I2C_BOARD_INFO("tps65910", 0x2d),
+ .platform_data = &tps65910_pdata,
+ },
+};
+
+static void __init am3517_crane_i2c_init(void)
+{
+ omap_register_i2c_bus(1, 2600, tps65910_board_info,
+ ARRAY_SIZE(tps65910_board_info));
+}
+
static void __init am3517_crane_init(void)
{
int ret;
@@ -96,6 +116,7 @@ static void __init am3517_crane_init(void)
board_nand_init(crane_nand_partitions,
ARRAY_SIZE(crane_nand_partitions), 0,
NAND_BUSWIDTH_16, NULL);
+ am3517_crane_i2c_init();

/* Configure GPIO for EHCI port */
if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
--
1.7.9.5

Best Regards,
Milo




\
 
 \ /
  Last update: 2012-11-29 09:01    [W:0.042 / U:0.328 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site