lkml.org 
[lkml]   [2012]   [Oct]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 0/2] Reset PCIe devices to address DMA problem on kdump with iommu
(2012/10/17 15:23), Takao Indoh wrote:
> These patches reset PCIe devices at boot time to address DMA problem on
> kdump with iommu. When "reset_devices" is specified, a hot reset is
> triggered on each PCIe root port and downstream port to reset its
> downstream endpoint.
>
> Background:
> A kdump problem about DMA has been discussed for a long time. That is,
> when a kernel is switched to the kdump kernel DMA derived from first
> kernel affects second kernel. Recently this problem surfaces when iommu
> is used for PCI passthrough on KVM guest. In the case of the machine I
> use, when intel_iommu=on is specified, DMAR error is detected in kdump
> kernel and PCI SERR is also detected. Finally kdump fails because some
> devices does not work correctly.
>
> The root cause is that ongoing DMA from first kernel causes DMAR fault
> because page table of DMAR is initialized while kdump kernel is booting
> up. Therefore to address this problem DMA needs to be stopped before
> DMAR is initialized at kdump kernel boot time. By these patches, PCIe
> devices are reset by hot reset and its DMA is stopped when reset_devices
> is specified. One problem of this solution is that the monitor blacks
> out when VGA controller is reset. So this patch does not reset the port
> whose child endpoint is VGA device.
>
> What I tried:
> - Clearing bus master bit and INTx disable bit at boot time
> This did not solve this problem. I still got DMAR error on devices.
> - Resetting devices in fixup_final(v1 patch)
> DMAR error disappeared, but sometimes PCI SERR was detected. This
> is well explained here.
> https://lkml.org/lkml/2012/9/9/245
> This PCI SERR seems to be related to interrupt remapping.
> - Clearing bus master in setup_arch() and resetting devices in
> fixup_final
> Neither DMAR error nor PCI SERR occurred. But on certain machine
> kdump kernel hung up when resetting devices. It seems to be a
> problem specific to the platform.
> - Resetting devices in setup_arch() (v2 and later patch)
> This solution solves all problems I found so far.
>
> v5:
> Do bus reset after all devices are scanned and its config registers are
> saved. This fixes a bug that config register is accessed without delay
> after reset.
>
> v4:
> Reduce waiting time after resetting devices. A previous patch does reset
> like this:
> for (each device) {
> save config registers
> reset
> wait for 500 ms
> restore config registers
> }
>
> If there are N devices to be reset, it takes N*500 ms. On the other
> hand, the v4 patch does:
> for (each device) {
> save config registers
> reset
> }
> wait 500 ms
> for (each device) {
> restore config registers
> }
> Though it needs more memory space to save config registers, the waiting
> time is always 500ms.
> https://lkml.org/lkml/2012/10/15/49
>
> v3:
> Move alloc_bootmem and free_bootmem to early_reset_pcie_devices so that
> they are called only once.
> https://lkml.org/lkml/2012/10/10/57
>
> v2:
> Reset devices in setup_arch() because reset need to be done before
> interrupt remapping is initialized.
> https://lkml.org/lkml/2012/10/2/54
>
> v1:
> Add fixup_final quirk to reset PCIe devices
> https://lkml.org/lkml/2012/8/3/160

Any other comments or ack/nack? If this is accepted I'll try multiple
domain support as next step.

Thanks,
Takao Indoh



\
 
 \ /
  Last update: 2012-10-31 12:41    [W:0.056 / U:0.904 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site