lkml.org 
[lkml]   [2010]   [Nov]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: pciehp - Problems with ExpressCard hotplug
(2010/11/04 14:06), Rafael J. Wysocki wrote:
> [CCing linux-pci and Bjorn]
>
> On Thursday, November 04, 2010, Mike DeKoker wrote:
>> Hello everyone, I hope this is the correct forum.
>>
>> I'm having a problem with hotplug working for a PCIe-based ExpressCard
>> device that I'm developing a driver module for. If not hot-plugged,
>> everything works great. Further, running the exact same laptop/device
>> hardware but different OS (XP or Win7-64) hot-plugging works okay so I don't
>> think this is a simple hardware/BIOS error.
>>
>> I've tried several stock kernel versions from 2.6.18 (the version my
>> customer intends to use) up to 2.6.34.7 (version for all verbiage below) and
>> have had fairly consistent behavior.
>>
>> The driver module (sig_ec14) is using the pci_register_driver interface and
>> in the subsequent probe callback function (after a hot-plug) an error occurs
>> when calling pci_enable_device. Here's the relevant dmesg data:
>>
>> Insert device:
>> pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
>> pci 0000:07:00.0: supports D1
>> pci 0000:07:00.0: PME# supported from D0 D1 D3hot
>> pci 0000:07:00.0: PME# disabled
>> pci 0000:07:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it
>> with 'pcie_aspm=force'
>> pci 0000:08:00.0: reg 10: [mem 0x00000000-0x0000001f]
>> pci 0000:08:00.0: reg 14: [mem 0x00000000-0x0000007f]
>> pci 0000:08:00.0: reg 18: [mem 0x00000000-0x0000003f]
>> pci 0000:07:00.0: PCI bridge to [bus 08-ff]
>> pci 0000:07:00.0: bridge window [io 0x0000-0x0000] (disabled)
>> pci 0000:07:00.0: bridge window [mem 0x00000000-0x000fffff] (disabled)
>> pci 0000:07:00.0: bridge window [mem 0x00000000-0x000fffff pref]
>> (disabled)
>> pci 0000:07:00.0: BAR 14: assigned [mem 0xd9000000-0xd90fffff]
>> pci 0000:07:00.0: PCI bridge to [bus 08-08]
>> pci 0000:07:00.0: bridge window [io disabled]
>> pci 0000:07:00.0: bridge window [mem 0xd9000000-0xd90fffff]
>> pci 0000:07:00.0: bridge window [mem pref disabled]
>> pcieport 0000:00:1c.5: PCI bridge to [bus 07-09]
>> pcieport 0000:00:1c.5: bridge window [io 0x1000-0x1fff]
>> pcieport 0000:00:1c.5: bridge window [mem 0xd9000000-0xd9ffffff]
>> pcieport 0000:00:1c.5: bridge window [mem 0xd8000000-0xd8ffffff 64bit
>> pref]
>> pcieport 0000:00:1c.5: setting latency timer to 64
>> pci 0000:07:00.0: enabling device (0000 -> 0002)
>> pci 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
>> pci 0000:07:00.0: setting latency timer to 64
>> pci 0000:07:00.0: no hotplug settings from platform
>> pci 0000:08:00.0: no hotplug settings from platform
>> pci 0000:08:00.0: using default PCI settings
>> sig_ec14 : Driver module loading
>> sig_ec14 : Verbose module output enabled (development build)
>> sig_ec14 : Dynamic major number: 248
>> sig_ec14 : PCI probe: New EC14 device
>> sig_ec14 0000:08:00.0: device not available (can't reserve [mem
>> 0x00000000-0x0000001f])
>> sig_ec14 : Failed to enable PCI device: -22
>> sig_ec14: probe of 0000:08:00.0 failed with error -22
>> .
>>
>> It looks like the requested memory spaces are not allocated properly. I'm a
>> little uncertain about the entity that's actually responsible for allocating
>> the resources. Is this a failure of the BIOS or does system software play a
>> role in PNP resource allocation for hot-plug? I'm a little out of my element
>> here.
>>
>> I've also run with pciehp_debug=1 in the event that the extra info makes
>> sense to someone:
>>
>> Insert device:
>> pciehp 0000:00:1c.5:pcie04: pcie_isr: intr_loc 8
>> pciehp 0000:00:1c.5:pcie04: Presence/Notify input change
>> pciehp 0000:00:1c.5:pcie04: Card present on Slot(5)
>> pciehp 0000:00:1c.5:pcie04: Surprise Removal
>> pciehp 0000:00:1c.5:pcie04: pciehp_check_link_status: lnk_status = 3011
>> pci 0000:07:00.0: supports D1
>> pci 0000:07:00.0: PME# supported from D0 D1 D3hot
>> pci 0000:07:00.0: PME# disabled
>> pci 0000:07:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it
>> with 'pcie_aspm=force'
>> .
>>
>> That 'Surprise Removal' immediately following the 'Card present on Slot(5)'
>> message looks like a potential culprit.

I believe this is just an message problem.

It looks like resource allocation code doesn't work for your
end device...

Could you send the following information

- whole dmesg output after hot-plugging the device (with pciehp_debug=1)
- lspci -vvvxxx output after boot with and without your device (no
hotplug operation required)

Thanks,
Kenji Kaneshige




\
 
 \ /
  Last update: 2010-11-05 07:01    [W:0.082 / U:2.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site