lkml.org 
[lkml]   [2008]   [Jul]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRe: [PATCH] ide: use proper printk() KERN_* levels in ide-probe.c
Date
On Monday 21 July 2008, Alan Cox wrote:
> On Mon, 21 Jul 2008 21:08:15 +0200
> Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> wrote:
>
> > While at it:
> >
> > - fixup printk() messages in save_match() and hwif_init().
> >
> > Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> > ---
> > drivers/ide/ide-probe.c | 54 ++++++++++++++++++++++++++----------------------
> > 1 file changed, 30 insertions(+), 24 deletions(-)
> >
> > Index: b/drivers/ide/ide-probe.c
> > ===================================================================
> > --- a/drivers/ide/ide-probe.c
> > +++ b/drivers/ide/ide-probe.c
> > @@ -141,7 +141,8 @@ static inline void do_identify (ide_driv
> > */
> > if ((id->model[0] == 'P' && id->model[1] == 'M') ||
> > (id->model[0] == 'S' && id->model[1] == 'K')) {
> > - printk("%s: EATA SCSI HBA %.10s\n", drive->name, id->model);
> > + printk(KERN_ERR "%s: EATA SCSI HBA %.10s\n",
> > + drive->name, id->model);
>
> That isn't an error. It occurs normally using legacy IDE with an EATA HBA
> present in ATA emulating mode.

Thanks for noticing, fix below.

From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Subject: [PATCH] ide: fix for EATA SCSI HBA in ATA emulating mode

IDE probing code used to skip devices attached to EATA SCSI HBA
in ATA emulating mode but because of warm-plug support port I/O
resources are no longer freed if no devices are detected on a port
and the decision about the driver to use is left up to the user.

Remove no longer valid EATA SCSI HBA quirk from do_identify().

Noticed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
goes before "ide: use proper printk() KERN_* levels in ide-probe.c"
patch in pata tree

drivers/ide/ide-probe.c | 12 ------------
1 file changed, 12 deletions(-)

Index: b/drivers/ide/ide-probe.c
===================================================================
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -134,18 +134,6 @@ static inline void do_identify (ide_driv
#endif
ide_fix_driveid(id);

-#if defined (CONFIG_SCSI_EATA_PIO) || defined (CONFIG_SCSI_EATA)
- /*
- * EATA SCSI controllers do a hardware ATA emulation:
- * Ignore them if there is a driver for them available.
- */
- if ((id->model[0] == 'P' && id->model[1] == 'M') ||
- (id->model[0] == 'S' && id->model[1] == 'K')) {
- printk("%s: EATA SCSI HBA %.10s\n", drive->name, id->model);
- goto err_misc;
- }
-#endif /* CONFIG_SCSI_EATA || CONFIG_SCSI_EATA_PIO */
-
/*
* WIN_IDENTIFY returns little-endian info,
* WIN_PIDENTIFY *usually* returns little-endian info.

\
 
 \ /
  Last update: 2008-07-22 22:53    [W:0.043 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site