lkml.org 
[lkml]   [2008]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: Longstanding bug in ac97/intel8x0 resume/init
Date
Johannes Weiner <hannes@saeurebad.de> writes:

> Hi,
>
> my laptop has muted sound after resuming the soundcard (by
> s2ram/hibernation). The problem seems to be that the cached register
> values are not written back to the device properly.
>
> Before suspend, the registers look like this:
>
> 0:00 = 1990
> 0:02 = 0000
> 0:04 = 9f1f
> 0:06 = 801f
> 0:08 = 0000
> 0:0a = 801e
> 0:0c = 801f
> 0:0e = 801f
> 0:10 = 9f1f
> 0:12 = 9f1f
> 0:14 = 9f1f
> 0:16 = 9f1f
> 0:18 = 0b0b
> 0:1a = 0000
> 0:1c = 0000
> 0:1e = 0000
> 0:20 = 0000
> 0:22 = 0000
> 0:24 = 0000
> 0:26 = 000f
> 0:28 = 0201
> 0:2a = 0001
> 0:2c = bb80
> 0:2e = 0000
> 0:30 = 0000
> 0:32 = bb80
> 0:34 = 0000
> 0:36 = 0000
> 0:38 = 0000
> 0:3a = 0000
> 0:3c = 0000
> 0:3e = 0000
> 0:40 = 0000
> 0:42 = 0000
> 0:44 = 0000
> 0:46 = 0000
> 0:48 = 0000
> 0:4a = 0000
> 0:4c = 0000
> 0:4e = 0000
> 0:50 = 0000
> 0:52 = 0000
> 0:54 = 0000
> 0:56 = ffff
> 0:58 = 0000
> 0:5a = 0604
> 0:5c = 0000
> 0:5e = 0080
> 0:60 = 0023
> 0:62 = 0000
> 0:64 = 0000
> 0:66 = 0000
> 0:68 = 0824
> 0:6a = 0000
> 0:6c = 0000
> 0:6e = 0000
> 0:70 = 0000
> 0:72 = 0000
> 0:74 = 0000
> 0:76 = 0000
> 0:78 = 003c
> 0:7a = 0000
> 0:7c = 4352
> 0:7e = 5936
>
> and right after a resume, they look like this (annotations by me):
>
> 0:00 = 1990
> 0:02 = 8000 ! Master Volume
> 0:04 = 8000 ! Headphone Volume
> 0:06 = 8000 ! Master Mono Volume
> 0:08 = 0000
> 0:0a = 0000 ! PC Beep Volume
> 0:0c = 8008 ! Phone Volume
> 0:0e = 8008 ! Mic Volume
> 0:10 = 8808 ! Line In Volume
> 0:12 = 8808 ! CD Volume
> 0:14 = 8808 ! Video Volume
> 0:16 = 8808 ! AUX Volume
> 0:18 = 8808 ! PCM Volume
> 0:1a = 0000
> 0:1c = 8000 ! Record gain
> 0:1e = 0000
> 0:20 = 0000
> 0:22 = 0000
> 0:24 = 0000
> 0:26 = 000f
> 0:28 = 0201
> 0:2a = 0001
> 0:2c = bb80
> 0:2e = 0000
> 0:30 = 0000
> 0:32 = bb80
> 0:34 = 0000
> 0:36 = 0000
> 0:38 = 0000
> 0:3a = 0000
> 0:3c = 0000
> 0:3e = 0000
> 0:40 = 0000
> 0:42 = 0000
> 0:44 = 0000
> 0:46 = 0000
> 0:48 = 0000
> 0:4a = 0000
> 0:4c = 0000
> 0:4e = 0000
> 0:50 = 0000
> 0:52 = 0000
> 0:54 = 0000
> 0:56 = ffff
> 0:58 = 0000
> 0:5a = 0604
> 0:5c = 0000
> 0:5e = 0080
> 0:60 = 0023
> 0:62 = 0000
> 0:64 = 0000
> 0:66 = 0000
> 0:68 = 0824
> 0:6a = 0000
> 0:6c = 0000
> 0:6e = 0000
> 0:70 = 0000
> 0:72 = 0000
> 0:74 = 0000
> 0:76 = 0000
> 0:78 = 003c
> 0:7a = 0000
> 0:7c = 4352
> 0:7e = 5936
>
> When I run alsamixer and change around the values of Master and PCM in a
> purely random way - a bit higher/lower, mute/unmute, etc. - sound comes
> back to life.
>
> I remember to `fix' this by adding more delays between waking the device
> and syncing back the cache. But I think that took up to 6 seconds,
> sometimes, so there must be something else going on (see below).
>
> The chip is the following:
>
> 0-0/0: Cirrus Logic CS4299 rev 6
>
> PCI Subsys Vendor: 0x1014
> PCI Subsys Device: 0x0222
>
> Capabilities : -headphone out-
> DAC resolution : 20-bit
> ADC resolution : 18-bit
> 3D enhancement : Crystal Semi 3D Stereo Enhancement
>
> Current setup
> Mic gain : +0dB [+0dB]
> POP path : pre 3D
> Sim. stereo : off
> 3D enhancement : off
> Loudness : off
> Mono output : MIX
> Mic select : Mic1
> ADC/DAC loopback : off
> Extended ID : codec=0 rev=0 AMAP DSA=0 VRA
> Extended status : VRA
> PCM front DAC : 48000Hz
> PCM ADC : 48000Hz
> SPDIF Control : Consumer PCM Copyright Category=0x22 Generation=1 Rate=48kHz
>
> Something else is strange, too. When I have the driver as a module and
> unload it once, another load will succeed module-wise but the device is
> unusable then. Here is the dmesg snippet:
>
> [ 1462.343612] ACPI: PCI interrupt for device 0000:00:1f.5 disabled
> [ 1487.092547] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
> [ 1487.094499] PCI: Setting latency timer of device 0000:00:1f.5 to 64
> [ 1488.347180] ALSA sound/pci/ac97/ac97_codec.c:2053: AC'97 0 does not respond - RESET
> [ 1488.347442] ACPI: PCI interrupt for device 0000:00:1f.5 disabled
> [ 1488.347569] Intel ICH: probe of 0000:00:1f.5 failed with error -13
>
> After another unload-load cycle, I get a working device again and this
> in dmesg:
>
> [ 2623.093209] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
> [ 2623.095264] PCI: Setting latency timer of device 0000:00:1f.5 to 64
> [ 2623.975121] intel8x0_measure_ac97_clock: measured 50399 usecs
> [ 2623.975268] intel8x0: clocking to 48000
>
> Please let me know if you need more information to debug this issue.
> It's really annoying :/
>
> Many thanks in advance,
> Hannes

Ping?


\
 
 \ /
  Last update: 2008-06-29 12:39    [W:0.075 / U:0.348 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site