Messages in this thread | | | From | Stefan Schweizer <> | Subject | Re: suspend | Date | Thu, 03 Apr 2008 09:42:00 +0200 |
| |
Oliver Neukum wrote: > Please load the appletouch module with the parameter "debug=1" and > post dmesg of a suspend/resume and the chvt thing.
I found out the appletouch issue was already discused here: http://lkml.org/lkml/2007/3/28/172
Unfortunately there seems to be no workaround and X-input still has more issues than it solves..
Attached is the dmesg excerpt
Best regards, Stefan
usbcore: deregistering interface driver appletouch input: appletouch disconnected appletouch: Geyser mode initialized. input: appletouch as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.1/input/input19 usbcore: registered new interface driver appletouch PM: Syncing filesystems ... done. Stopping fuse filesystems. Freezing user space processes ... (elapsed 0.00 seconds) <6>done. Stopping normal filesystems. Freezing remaining freezable tasks ... (elapsed 0.00 seconds) <6>done. ACPI: Preparing to enter system sleep state S3 Suspending console(s) sd 2:0:1:0: [sda] Synchronizing SCSI cache sd 2:0:1:0: [sda] Stopping disk ACPI handle has no context! ACPI: PCI interrupt for device 0000:02:00.0 disabled sky2 eth0: disabling interface ACPI: PCI interrupt for device 0000:00:1f.2 disabled ACPI: PCI interrupt for device 0000:00:1f.1 disabled ACPI: PCI interrupt for device 0000:00:1d.7 disabled ACPI: PCI interrupt for device 0000:00:1d.3 disabled ACPI: PCI interrupt for device 0000:00:1d.2 disabled ACPI: PCI interrupt for device 0000:00:1d.1 disabled ACPI: PCI interrupt for device 0000:00:1d.0 disabled ACPI: PCI interrupt for device 0000:00:1b.0 disabled Disabling non-boot CPUs ... CPU 1 is now offline SMP alternatives: switching to UP code CPU1 is down Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Back to C! Enabling non-boot CPUs ... SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3995.35 BogoMIPS (lpj=1997676) CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 00000000 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Genuine Intel(R) CPU T2500 @ 2.00GHz stepping 08 CPU1 is up Switched to high resolution mode on CPU 1 PM: Writing back config space on device 0000:00:02.0 at offset f (was 100, writing 10a) PM: Writing back config space on device 0000:00:02.0 at offset 7 (was 0, writing 90400000) PM: Writing back config space on device 0000:00:02.0 at offset 6 (was 8, writing 80000008) PM: Writing back config space on device 0000:00:02.0 at offset 5 (was 1, writing 20f1) PM: Writing back config space on device 0000:00:02.0 at offset 4 (was 0, writing 90380000) PM: Writing back config space on device 0000:00:02.0 at offset 1 (was 900000, writing 900007) ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:02.0 to 64 PM: Writing back config space on device 0000:00:02.1 at offset 4 (was 0, writing 90300000) PM: Writing back config space on device 0000:00:02.1 at offset 1 (was 900000, writing 900007) PM: Writing back config space on device 0000:00:07.0 at offset f (was 100, writing 10a) PM: Writing back config space on device 0000:00:07.0 at offset 4 (was 0, writing 90444000) PM: Writing back config space on device 0000:00:07.0 at offset 1 (was b00000, writing b00002) PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing 90440004) PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 40) PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002) ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1b.0 to 64 PM: Writing back config space on device 0000:00:1c.0 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:00:1c.0 at offset 9 (was 10001, writing 50015001) PM: Writing back config space on device 0000:00:1c.0 at offset 8 (was 0, writing 90209020) PM: Writing back config space on device 0000:00:1c.0 at offset 7 (was 20000000, writing 20001010) PM: Writing back config space on device 0000:00:1c.0 at offset 6 (was 0, writing 10100) PM: Writing back config space on device 0000:00:1c.0 at offset 3 (was 810000, writing 810040) PM: Writing back config space on device 0000:00:1c.0 at offset 1 (was 100000, writing 100007) PCI: Setting latency timer of device 0000:00:1c.0 to 64 PM: Writing back config space on device 0000:00:1c.1 at offset f (was 200, writing 20a) PM: Writing back config space on device 0000:00:1c.1 at offset 9 (was 10001, writing 1fff1) PM: Writing back config space on device 0000:00:1c.1 at offset 8 (was 0, writing 90109010) PM: Writing back config space on device 0000:00:1c.1 at offset 7 (was 20000000, writing f0) PM: Writing back config space on device 0000:00:1c.1 at offset 6 (was 0, writing 20200) PM: Writing back config space on device 0000:00:1c.1 at offset 3 (was 810000, writing 810040) PM: Writing back config space on device 0000:00:1c.1 at offset 1 (was 100000, writing 100007) PCI: Setting latency timer of device 0000:00:1c.1 to 64 PCI: Enabling device 0000:00:1d.0 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 PM: Writing back config space on device 0000:00:1d.0 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:00:1d.0 at offset 8 (was 1, writing 20a1) usb usb1: root hub lost power or was reset PCI: Enabling device 0000:00:1d.1 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.1 to 64 PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200, writing 20b) PM: Writing back config space on device 0000:00:1d.1 at offset 8 (was 1, writing 2081) usb usb2: root hub lost power or was reset PCI: Enabling device 0000:00:1d.2 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300, writing 30b) PM: Writing back config space on device 0000:00:1d.2 at offset 8 (was 1, writing 2061) usb usb3: root hub lost power or was reset PCI: Enabling device 0000:00:1d.3 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.3 to 64 PM: Writing back config space on device 0000:00:1d.3 at offset f (was 400, writing 40a) PM: Writing back config space on device 0000:00:1d.3 at offset 8 (was 1, writing 2041) usb usb4: root hub lost power or was reset PCI: Enabling device 0000:00:1d.7 (0000 -> 0002) ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing 90445400) PM: Writing back config space on device 0000:00:1e.0 at offset 9 (was 10001, writing 1fff1) PM: Writing back config space on device 0000:00:1e.0 at offset 8 (was 0, writing 90009000) PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was 22800000, writing 228000f0) PM: Writing back config space on device 0000:00:1e.0 at offset 6 (was 0, writing 20030300) PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100000, writing 100007) PCI: Setting latency timer of device 0000:00:1e.0 to 64 PM: Writing back config space on device 0000:00:1f.1 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:00:1f.1 at offset 1 (was 2800001, writing 2800005) ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1f.1 to 64 PM: Writing back config space on device 0000:00:1f.2 at offset f (was 200, writing 20b) PM: Writing back config space on device 0000:00:1f.2 at offset 8 (was 1, writing 2021) PM: Writing back config space on device 0000:00:1f.2 at offset 1 (was 2b00002, writing 2b00007) ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1f.2 to 64 PM: Writing back config space on device 0000:00:1f.3 at offset f (was 200, writing 20b) PM: Writing back config space on device 0000:01:00.0 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:01:00.0 at offset c (was 0, writing fffe0000) PM: Writing back config space on device 0000:01:00.0 at offset 6 (was 1, writing 1001) PM: Writing back config space on device 0000:01:00.0 at offset 4 (was 4, writing 90200004) PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 40) PM: Writing back config space on device 0000:01:00.0 at offset 1 (was 40100000, writing 100007) sky2 eth0: enabling interface PM: Writing back config space on device 0000:02:00.0 at offset f (was 100, writing 10b) PM: Writing back config space on device 0000:02:00.0 at offset 4 (was 4, writing 90100004) PM: Writing back config space on device 0000:02:00.0 at offset 3 (was 0, writing 40) PM: Writing back config space on device 0000:02:00.0 at offset 1 (was 100000, writing 100007) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:02:00.0 to 64 PM: Writing back config space on device 0000:03:03.0 at offset f (was 180c0100, writing 180c010b) PM: Writing back config space on device 0000:03:03.0 at offset 4 (was 0, writing 90000000) PM: Writing back config space on device 0000:03:03.0 at offset 3 (was 0, writing f810) PM: Writing back config space on device 0000:03:03.0 at offset 1 (was 2900000, writing 2900216) sd 2:0:1:0: [sda] Starting disk ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out ata1.00: ACPI cmd ef/03:44:00:00:00:a0 filtered out ata3.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out ata3.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out ata3.01: configured for UDMA/100 sd 2:0:1:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 2:0:1:0: [sda] Write Protect is off sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata1.00: configured for UDMA/66 restoring control 00000000-0000-0000-0000-000000000101/0/2 restoring control 00000000-0000-0000-0000-000000000101/3/7 restoring control 00000000-0000-0000-0000-000000000101/5/9 applesmc: received a shock interrupt applesmc: cannot setup irq handler applesmc: accelerometer successfully initialized. Restarting all filesystems ... Restarting tasks ... <6>usb 1-1: USB disconnect, address 6 done. usb 1-1: new low speed USB device using uhci_hcd and address 8 usb 1-1: configuration #1 chosen from 1 choice input: HID 0461:4d03 as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input20 input: USB HID v1.10 Mouse [HID 0461:4d03] on usb-0000:00:1d.0-1 usb 1-2: USB disconnect, address 7 input: appletouch disconnected usb 1-2: new full speed USB device using uhci_hcd and address 9 usb 1-2: configuration #1 chosen from 1 choice input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/input/input21 input: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2 appletouch: Geyser mode initialized. input: appletouch as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.1/input/input22 appletouch: incomplete data package (first byte: 2, length: 4). input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.2/input/input23 input: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2 usb 3-2: USB disconnect, address 3 usb 3-2: new full speed USB device using uhci_hcd and address 4 usb 3-2: configuration #1 chosen from 1 choice hiddev0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-2 usb 4-1: USB disconnect, address 3 usb 4-1: new full speed USB device using uhci_hcd and address 4 usb 4-1: configuration #1 chosen from 1 choice input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.0/input/input24 input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1d.3-1 input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.1/input/input25 input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1d.3-1
| |