lkml.org 
[lkml]   [2008]   [Apr]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[git pull] "big box" x86 changes, PCI

ok, this is the final chunk of the "big box" topic - the PCI changes.

These are the largest, and while i tried to reduce their number it's
still 19 commits - but it's all around the same topic. The bulk of the
new code is in a single file. The tree can be pulled from:

git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci.git for-linus

this depends on the bootmem changes which are now upstream. These
changes too have been in linux-next for some time and the cross-arch
(build) success rate is high, as in:

http://www.tglx.de/autoqa-cgi/index?run=89&tree=1

all but the last few patches have been in x86.git for a longer time and
more than 95% of the changes are for arch/x86. (see the dates of the
patches. The "15 Feb 2008" ones are older than their timestamp - that's
when we imported those changes into a date-aware repository.)

i booted up this tree 5 times on x86, mixed 64-bit/32-bit.

Ingo

------------------>
Robert Hancock (1):
x86: validate against acpi motherboard resources

Yinghai Lu (18):
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: mmconf enable mcfg early
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86: if acpi=off, force setting the mmconf for fam10h
x86: seperate mmconf for fam10h out from setup_64.c
driver core: try parent numa_node at first before using default
x86: remove unneeded check in mmconf reject
x86 pci: remove checking type for mmconfig probe
x86: get mp_bus_to_node early
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: multi pci root bus with different io resource range, on 64-bit
x86: double check the multi root bus with fam10h mmconf
x86_64: don't need set default res if only have one root bus
acpi: get boot_cpu_id as early for k8_scan_nodes
x86: work around io allocation overlap of HT links
x86: add pci=check_enable_amd_mmconf and dmi check

arch/x86/kernel/Makefile | 2 +
arch/x86/kernel/acpi/boot.c | 70 +++++
arch/x86/kernel/mmconf-fam10h_64.c | 243 +++++++++++++++
arch/x86/kernel/setup_64.c | 20 ++
arch/x86/mm/k8topology_64.c | 38 +++-
arch/x86/pci/Makefile_32 | 1 +
arch/x86/pci/Makefile_64 | 2 +-
arch/x86/pci/acpi.c | 27 +-
arch/x86/pci/common.c | 22 ++-
arch/x86/pci/direct.c | 8 +-
arch/x86/pci/fixup.c | 17 +
arch/x86/pci/init.c | 13 +-
arch/x86/pci/irq.c | 4 +-
arch/x86/pci/k8-bus_64.c | 575 ++++++++++++++++++++++++++++++++----
arch/x86/pci/legacy.c | 4 +-
arch/x86/pci/mmconfig-shared.c | 247 +++++++++++++---
arch/x86/pci/mmconfig_32.c | 4 +
arch/x86/pci/mmconfig_64.c | 22 ++-
arch/x86/pci/mp_bus_to_node.c | 23 ++
arch/x86/pci/pci.h | 3 +-
drivers/acpi/bus.c | 2 +
drivers/base/core.c | 14 +-
drivers/pci/probe.c | 21 ++-
include/asm-x86/pci.h | 2 +
include/asm-x86/topology.h | 16 +
include/linux/acpi.h | 5 +
include/linux/pci.h | 11 +-
27 files changed, 1284 insertions(+), 132 deletions(-)
create mode 100644 arch/x86/kernel/mmconf-fam10h_64.c
create mode 100644 arch/x86/pci/mp_bus_to_node.c

diff --git a/arch/x86/kernel/Makefile b/arch/x86/kernel/Makefile
index 90e092d..815b650 100644
--- a/arch/x86/kernel/Makefile
+++ b/arch/x86/kernel/Makefile
@@ -99,4 +99,6 @@ ifeq ($(CONFIG_X86_64),y)
obj-$(CONFIG_GART_IOMMU) += pci-gart_64.o aperture_64.o
obj-$(CONFIG_CALGARY_IOMMU) += pci-calgary_64.o tce_64.o
obj-$(CONFIG_SWIOTLB) += pci-swiotlb_64.o
+
+ obj-$(CONFIG_PCI_MMCONFIG) += mmconf-fam10h_64.o
endif
diff --git a/arch/x86/kernel/acpi/boot.c b/arch/x86/kernel/acpi/boot.c
index 977ed5c..c49ebcc 100644
--- a/arch/x86/kernel/acpi/boot.c
+++ b/arch/x86/kernel/acpi/boot.c
@@ -771,6 +771,32 @@ static void __init acpi_register_lapic_address(unsigned long address)
boot_cpu_physical_apicid = GET_APIC_ID(read_apic_id());
}

+static int __init early_acpi_parse_madt_lapic_addr_ovr(void)
+{
+ int count;
+
+ if (!cpu_has_apic)
+ return -ENODEV;
+
+ /*
+ * Note that the LAPIC address is obtained from the MADT (32-bit value)
+ * and (optionally) overriden by a LAPIC_ADDR_OVR entry (64-bit value).
+ */
+
+ count =
+ acpi_table_parse_madt(ACPI_MADT_TYPE_LOCAL_APIC_OVERRIDE,
+ acpi_parse_lapic_addr_ovr, 0);
+ if (count < 0) {
+ printk(KERN_ERR PREFIX
+ "Error parsing LAPIC address override entry\n");
+ return count;
+ }
+
+ acpi_register_lapic_address(acpi_lapic_addr);
+
+ return count;
+}
+
static int __init acpi_parse_madt_lapic_entries(void)
{
int count;
@@ -901,6 +927,33 @@ static inline int acpi_parse_madt_ioapic_entries(void)
}
#endif /* !CONFIG_X86_IO_APIC */

+static void __init early_acpi_process_madt(void)
+{
+#ifdef CONFIG_X86_LOCAL_APIC
+ int error;
+
+ if (!acpi_table_parse(ACPI_SIG_MADT, acpi_parse_madt)) {
+
+ /*
+ * Parse MADT LAPIC entries
+ */
+ error = early_acpi_parse_madt_lapic_addr_ovr();
+ if (!error) {
+ acpi_lapic = 1;
+ smp_found_config = 1;
+ }
+ if (error == -EINVAL) {
+ /*
+ * Dell Precision Workstation 410, 610 come here.
+ */
+ printk(KERN_ERR PREFIX
+ "Invalid BIOS MADT, disabling ACPI\n");
+ disable_acpi();
+ }
+ }
+#endif
+}
+
static void __init acpi_process_madt(void)
{
#ifdef CONFIG_X86_LOCAL_APIC
@@ -1233,6 +1286,23 @@ int __init acpi_boot_table_init(void)
return 0;
}

+int __init early_acpi_boot_init(void)
+{
+ /*
+ * If acpi_disabled, bail out
+ * One exception: acpi=ht continues far enough to enumerate LAPICs
+ */
+ if (acpi_disabled && !acpi_ht)
+ return 1;
+
+ /*
+ * Process the Multiple APIC Description Table (MADT), if present
+ */
+ early_acpi_process_madt();
+
+ return 0;
+}
+
int __init acpi_boot_init(void)
{
/*
diff --git a/arch/x86/kernel/mmconf-fam10h_64.c b/arch/x86/kernel/mmconf-fam10h_64.c
new file mode 100644
index 0000000..edc5fbf
--- /dev/null
+++ b/arch/x86/kernel/mmconf-fam10h_64.c
@@ -0,0 +1,243 @@
+/*
+ * AMD Family 10h mmconfig enablement
+ */
+
+#include <linux/types.h>
+#include <linux/mm.h>
+#include <linux/string.h>
+#include <linux/pci.h>
+#include <linux/dmi.h>
+#include <asm/pci-direct.h>
+#include <linux/sort.h>
+#include <asm/io.h>
+#include <asm/msr.h>
+#include <asm/acpi.h>
+
+#include "../pci/pci.h"
+
+struct pci_hostbridge_probe {
+ u32 bus;
+ u32 slot;
+ u32 vendor;
+ u32 device;
+};
+
+static u64 __cpuinitdata fam10h_pci_mmconf_base;
+static int __cpuinitdata fam10h_pci_mmconf_base_status;
+
+static struct pci_hostbridge_probe pci_probes[] __cpuinitdata = {
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
+};
+
+struct range {
+ u64 start;
+ u64 end;
+};
+
+static int __cpuinit cmp_range(const void *x1, const void *x2)
+{
+ const struct range *r1 = x1;
+ const struct range *r2 = x2;
+ int start1, start2;
+
+ start1 = r1->start >> 32;
+ start2 = r2->start >> 32;
+
+ return start1 - start2;
+}
+
+/*[47:0] */
+/* need to avoid (0xfd<<32) and (0xfe<<32), ht used space */
+#define FAM10H_PCI_MMCONF_BASE (0xfcULL<<32)
+#define BASE_VALID(b) ((b != (0xfdULL << 32)) && (b != (0xfeULL << 32)))
+static void __cpuinit get_fam10h_pci_mmconf_base(void)
+{
+ int i;
+ unsigned bus;
+ unsigned slot;
+ int found;
+
+ u64 val;
+ u32 address;
+ u64 tom2;
+ u64 base = FAM10H_PCI_MMCONF_BASE;
+
+ int hi_mmio_num;
+ struct range range[8];
+
+ /* only try to get setting from BSP */
+ /* -1 or 1 */
+ if (fam10h_pci_mmconf_base_status)
+ return;
+
+ if (!early_pci_allowed())
+ goto fail;
+
+ found = 0;
+ for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+ u32 id;
+ u16 device;
+ u16 vendor;
+
+ bus = pci_probes[i].bus;
+ slot = pci_probes[i].slot;
+ id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
+
+ vendor = id & 0xffff;
+ device = (id>>16) & 0xffff;
+ if (pci_probes[i].vendor == vendor &&
+ pci_probes[i].device == device) {
+ found = 1;
+ break;
+ }
+ }
+
+ if (!found)
+ goto fail;
+
+ /* SYS_CFG */
+ address = MSR_K8_SYSCFG;
+ rdmsrl(address, val);
+
+ /* TOP_MEM2 is not enabled? */
+ if (!(val & (1<<21))) {
+ tom2 = 0;
+ } else {
+ /* TOP_MEM2 */
+ address = MSR_K8_TOP_MEM2;
+ rdmsrl(address, val);
+ tom2 = val & (0xffffULL<<32);
+ }
+
+ if (base <= tom2)
+ base = tom2 + (1ULL<<32);
+
+ /*
+ * need to check if the range is in the high mmio range that is
+ * above 4G
+ */
+ hi_mmio_num = 0;
+ for (i = 0; i < 8; i++) {
+ u32 reg;
+ u64 start;
+ u64 end;
+ reg = read_pci_config(bus, slot, 1, 0x80 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = (((u64)reg) << 8) & (0xffULL << 32); /* 39:16 on 31:8*/
+ reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
+ end = (((u64)reg) << 8) & (0xffULL << 32); /* 39:16 on 31:8*/
+
+ if (!end)
+ continue;
+
+ range[hi_mmio_num].start = start;
+ range[hi_mmio_num].end = end;
+ hi_mmio_num++;
+ }
+
+ if (!hi_mmio_num)
+ goto out;
+
+ /* sort the range */
+ sort(range, hi_mmio_num, sizeof(struct range), cmp_range, NULL);
+
+ if (range[hi_mmio_num - 1].end < base)
+ goto out;
+ if (range[0].start > base)
+ goto out;
+
+ /* need to find one window */
+ base = range[0].start - (1ULL << 32);
+ if ((base > tom2) && BASE_VALID(base))
+ goto out;
+ base = range[hi_mmio_num - 1].end + (1ULL << 32);
+ if ((base > tom2) && BASE_VALID(base))
+ goto out;
+ /* need to find window between ranges */
+ if (hi_mmio_num > 1)
+ for (i = 0; i < hi_mmio_num - 1; i++) {
+ if (range[i + 1].start > (range[i].end + (1ULL << 32))) {
+ base = range[i].end + (1ULL << 32);
+ if ((base > tom2) && BASE_VALID(base))
+ goto out;
+ }
+ }
+
+fail:
+ fam10h_pci_mmconf_base_status = -1;
+ return;
+out:
+ fam10h_pci_mmconf_base = base;
+ fam10h_pci_mmconf_base_status = 1;
+}
+
+void __cpuinit fam10h_check_enable_mmcfg(void)
+{
+ u64 val;
+ u32 address;
+
+ if (!(pci_probe & PCI_CHECK_ENABLE_AMD_MMCONF))
+ return;
+
+ address = MSR_FAM10H_MMIO_CONF_BASE;
+ rdmsrl(address, val);
+
+ /* try to make sure that AP's setting is identical to BSP setting */
+ if (val & FAM10H_MMIO_CONF_ENABLE) {
+ unsigned busnbits;
+ busnbits = (val >> FAM10H_MMIO_CONF_BUSRANGE_SHIFT) &
+ FAM10H_MMIO_CONF_BUSRANGE_MASK;
+
+ /* only trust the one handle 256 buses, if acpi=off */
+ if (!acpi_pci_disabled || busnbits >= 8) {
+ u64 base;
+ base = val & (0xffffULL << 32);
+ if (fam10h_pci_mmconf_base_status <= 0) {
+ fam10h_pci_mmconf_base = base;
+ fam10h_pci_mmconf_base_status = 1;
+ return;
+ } else if (fam10h_pci_mmconf_base == base)
+ return;
+ }
+ }
+
+ /*
+ * if it is not enabled, try to enable it and assume only one segment
+ * with 256 buses
+ */
+ get_fam10h_pci_mmconf_base();
+ if (fam10h_pci_mmconf_base_status <= 0)
+ return;
+
+ printk(KERN_INFO "Enable MMCONFIG on AMD Family 10h\n");
+ val &= ~((FAM10H_MMIO_CONF_BASE_MASK<<FAM10H_MMIO_CONF_BASE_SHIFT) |
+ (FAM10H_MMIO_CONF_BUSRANGE_MASK<<FAM10H_MMIO_CONF_BUSRANGE_SHIFT));
+ val |= fam10h_pci_mmconf_base | (8 << FAM10H_MMIO_CONF_BUSRANGE_SHIFT) |
+ FAM10H_MMIO_CONF_ENABLE;
+ wrmsrl(address, val);
+}
+
+static int __devinit set_check_enable_amd_mmconf(const struct dmi_system_id *d)
+{
+ pci_probe |= PCI_CHECK_ENABLE_AMD_MMCONF;
+ return 0;
+}
+
+static struct dmi_system_id __devinitdata mmconf_dmi_table[] = {
+ {
+ .callback = set_check_enable_amd_mmconf,
+ .ident = "Sun Microsystems Machine",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Sun Microsystems"),
+ },
+ },
+ {}
+};
+
+void __init check_enable_amd_mmconf_dmi(void)
+{
+ dmi_check_system(mmconf_dmi_table);
+}
diff --git a/arch/x86/kernel/setup_64.c b/arch/x86/kernel/setup_64.c
index 60e64c8..2f5c488 100644
--- a/arch/x86/kernel/setup_64.c
+++ b/arch/x86/kernel/setup_64.c
@@ -29,6 +29,7 @@
#include <linux/crash_dump.h>
#include <linux/root_dev.h>
#include <linux/pci.h>
+#include <asm/pci-direct.h>
#include <linux/efi.h>
#include <linux/acpi.h>
#include <linux/kallsyms.h>
@@ -40,6 +41,7 @@
#include <linux/dmi.h>
#include <linux/dma-mapping.h>
#include <linux/ctype.h>
+#include <linux/sort.h>
#include <linux/uaccess.h>
#include <linux/init_ohci1394_dma.h>

@@ -287,6 +289,18 @@ static void __init parse_setup_data(void)
}
}

+#ifdef CONFIG_PCI_MMCONFIG
+extern void __cpuinit fam10h_check_enable_mmcfg(void);
+extern void __init check_enable_amd_mmconf_dmi(void);
+#else
+void __cpuinit fam10h_check_enable_mmcfg(void)
+{
+}
+void __init check_enable_amd_mmconf_dmi(void)
+{
+}
+#endif
+
/*
* setup_arch - architecture-specific boot-time initializations
*
@@ -508,6 +522,9 @@ void __init setup_arch(char **cmdline_p)
conswitchp = &dummy_con;
#endif
#endif
+
+ /* do this before identify_cpu for boot cpu */
+ check_enable_amd_mmconf_dmi();
}

static int __cpuinit get_model_name(struct cpuinfo_x86 *c)
@@ -760,6 +777,9 @@ static void __cpuinit init_amd(struct cpuinfo_x86 *c)
/* MFENCE stops RDTSC speculation */
set_cpu_cap(c, X86_FEATURE_MFENCE_RDTSC);

+ if (c->x86 == 0x10)
+ fam10h_check_enable_mmcfg();
+
if (amd_apic_timer_broken())
disable_apic_timer = 1;

diff --git a/arch/x86/mm/k8topology_64.c b/arch/x86/mm/k8topology_64.c
index 86808e6..1f476e4 100644
--- a/arch/x86/mm/k8topology_64.c
+++ b/arch/x86/mm/k8topology_64.c
@@ -13,12 +13,15 @@
#include <linux/nodemask.h>
#include <asm/io.h>
#include <linux/pci_ids.h>
+#include <linux/acpi.h>
#include <asm/types.h>
#include <asm/mmzone.h>
#include <asm/proto.h>
#include <asm/e820.h>
#include <asm/pci-direct.h>
#include <asm/numa.h>
+#include <asm/mpspec.h>
+#include <asm/apic.h>

static __init int find_northbridge(void)
{
@@ -44,6 +47,30 @@ static __init int find_northbridge(void)
return -1;
}

+static __init void early_get_boot_cpu_id(void)
+{
+ /*
+ * need to get boot_cpu_id so can use that to create apicid_to_node
+ * in k8_scan_nodes()
+ */
+ /*
+ * Find possible boot-time SMP configuration:
+ */
+ early_find_smp_config();
+#ifdef CONFIG_ACPI
+ /*
+ * Read APIC information from ACPI tables.
+ */
+ early_acpi_boot_init();
+#endif
+ /*
+ * get boot-time SMP configuration:
+ */
+ if (smp_found_config)
+ early_get_smp_config();
+ early_init_lapic_mapping();
+}
+
int __init k8_scan_nodes(unsigned long start, unsigned long end)
{
unsigned long prevbase;
@@ -56,6 +83,7 @@ int __init k8_scan_nodes(unsigned long start, unsigned long end)
unsigned cores;
unsigned bits;
int j;
+ unsigned apicid_base;

if (!early_pci_allowed())
return -1;
@@ -174,11 +202,19 @@ int __init k8_scan_nodes(unsigned long start, unsigned long end)
/* use the coreid bits from early_identify_cpu */
bits = boot_cpu_data.x86_coreid_bits;
cores = (1<<bits);
+ apicid_base = 0;
+ /* need to get boot_cpu_id early for system with apicid lifting */
+ early_get_boot_cpu_id();
+ if (boot_cpu_physical_apicid > 0) {
+ printk(KERN_INFO "BSP APIC ID: %02x\n",
+ boot_cpu_physical_apicid);
+ apicid_base = boot_cpu_physical_apicid;
+ }

for (i = 0; i < 8; i++) {
if (nodes[i].start != nodes[i].end) {
nodeid = nodeids[i];
- for (j = 0; j < cores; j++)
+ for (j = apicid_base; j < cores + apicid_base; j++)
apicid_to_node[(nodeid << bits) + j] = i;
setup_node_bootmem(i, nodes[i].start, nodes[i].end);
}
diff --git a/arch/x86/pci/Makefile_32 b/arch/x86/pci/Makefile_32
index cdd6828..e9c5caf 100644
--- a/arch/x86/pci/Makefile_32
+++ b/arch/x86/pci/Makefile_32
@@ -10,5 +10,6 @@ pci-y += legacy.o irq.o

pci-$(CONFIG_X86_VISWS) := visws.o fixup.o
pci-$(CONFIG_X86_NUMAQ) := numa.o irq.o
+pci-$(CONFIG_NUMA) += mp_bus_to_node.o

obj-y += $(pci-y) common.o early.o
diff --git a/arch/x86/pci/Makefile_64 b/arch/x86/pci/Makefile_64
index 7d8c467..8fbd198 100644
--- a/arch/x86/pci/Makefile_64
+++ b/arch/x86/pci/Makefile_64
@@ -13,5 +13,5 @@ obj-y += legacy.o irq.o common.o early.o
# mmconfig has a 64bit special
obj-$(CONFIG_PCI_MMCONFIG) += mmconfig_64.o direct.o mmconfig-shared.o

-obj-$(CONFIG_NUMA) += k8-bus_64.o
+obj-y += k8-bus_64.o

diff --git a/arch/x86/pci/acpi.c b/arch/x86/pci/acpi.c
index 2664cb3..1a9c0c6 100644
--- a/arch/x86/pci/acpi.c
+++ b/arch/x86/pci/acpi.c
@@ -191,7 +191,10 @@ struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int do
{
struct pci_bus *bus;
struct pci_sysdata *sd;
+ int node;
+#ifdef CONFIG_ACPI_NUMA
int pxm;
+#endif

dmi_check_system(acpi_pciprobe_dmi_table);

@@ -201,6 +204,17 @@ struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int do
return NULL;
}

+ node = -1;
+#ifdef CONFIG_ACPI_NUMA
+ pxm = acpi_get_pxm(device->handle);
+ if (pxm >= 0)
+ node = pxm_to_node(pxm);
+ if (node != -1)
+ set_mp_bus_to_node(busnum, node);
+ else
+ node = get_mp_bus_to_node(busnum);
+#endif
+
/* Allocate per-root-bus (not per bus) arch-specific data.
* TODO: leak; this memory is never freed.
* It's arguable whether it's worth the trouble to care.
@@ -212,13 +226,7 @@ struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int do
}

sd->domain = domain;
- sd->node = -1;
-
- pxm = acpi_get_pxm(device->handle);
-#ifdef CONFIG_ACPI_NUMA
- if (pxm >= 0)
- sd->node = pxm_to_node(pxm);
-#endif
+ sd->node = node;
/*
* Maybe the desired pci bus has been already scanned. In such case
* it is unnecessary to scan the pci bus with the given domain,busnum.
@@ -238,9 +246,9 @@ struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int do
kfree(sd);

#ifdef CONFIG_ACPI_NUMA
- if (bus != NULL) {
+ if (bus) {
if (pxm >= 0) {
- printk("bus %d -> pxm %d -> node %d\n",
+ printk(KERN_DEBUG "bus %02x -> pxm %d -> node %d\n",
busnum, pxm, pxm_to_node(pxm));
}
}
@@ -248,7 +256,6 @@ struct pci_bus * __devinit pci_acpi_scan_root(struct acpi_device *device, int do

if (bus && (pci_probe & PCI_USE__CRS))
get_current_resources(device, busnum, domain, bus);
-
return bus;
}

diff --git a/arch/x86/pci/common.c b/arch/x86/pci/common.c
index 75fcc29..2a4d751 100644
--- a/arch/x86/pci/common.c
+++ b/arch/x86/pci/common.c
@@ -342,9 +342,14 @@ struct pci_bus * __devinit pcibios_scan_root(int busnum)
return NULL;
}

+ sd->node = get_mp_bus_to_node(busnum);
+
printk(KERN_DEBUG "PCI: Probing PCI hardware (bus %02x)\n", busnum);
+ bus = pci_scan_bus_parented(NULL, busnum, &pci_root_ops, sd);
+ if (!bus)
+ kfree(sd);

- return pci_scan_bus_parented(NULL, busnum, &pci_root_ops, sd);
+ return bus;
}

extern u8 pci_cache_line_size;
@@ -420,6 +425,10 @@ char * __devinit pcibios_setup(char *str)
pci_probe &= ~PCI_PROBE_MMCONF;
return NULL;
}
+ else if (!strcmp(str, "check_enable_amd_mmconf")) {
+ pci_probe |= PCI_CHECK_ENABLE_AMD_MMCONF;
+ return NULL;
+ }
#endif
else if (!strcmp(str, "noacpi")) {
acpi_noirq_set();
@@ -480,7 +489,7 @@ void pcibios_disable_device (struct pci_dev *dev)
pcibios_disable_irq(dev);
}

-struct pci_bus *__devinit pci_scan_bus_with_sysdata(int busno)
+struct pci_bus *pci_scan_bus_on_node(int busno, struct pci_ops *ops, int node)
{
struct pci_bus *bus = NULL;
struct pci_sysdata *sd;
@@ -495,10 +504,15 @@ struct pci_bus *__devinit pci_scan_bus_with_sysdata(int busno)
printk(KERN_ERR "PCI: OOM, skipping PCI bus %02x\n", busno);
return NULL;
}
- sd->node = -1;
- bus = pci_scan_bus(busno, &pci_root_ops, sd);
+ sd->node = node;
+ bus = pci_scan_bus(busno, ops, sd);
if (!bus)
kfree(sd);

return bus;
}
+
+struct pci_bus *pci_scan_bus_with_sysdata(int busno)
+{
+ return pci_scan_bus_on_node(busno, &pci_root_ops, -1);
+}
diff --git a/arch/x86/pci/direct.c b/arch/x86/pci/direct.c
index 42f3e4c..21d1e0e 100644
--- a/arch/x86/pci/direct.c
+++ b/arch/x86/pci/direct.c
@@ -258,7 +258,8 @@ void __init pci_direct_init(int type)
{
if (type == 0)
return;
- printk(KERN_INFO "PCI: Using configuration type %d\n", type);
+ printk(KERN_INFO "PCI: Using configuration type %d for base access\n",
+ type);
if (type == 1)
raw_pci_ops = &pci_direct_conf1;
else
@@ -275,8 +276,10 @@ int __init pci_direct_probe(void)
if (!region)
goto type2;

- if (pci_check_type1())
+ if (pci_check_type1()) {
+ raw_pci_ops = &pci_direct_conf1;
return 1;
+ }
release_resource(region);

type2:
@@ -290,7 +293,6 @@ int __init pci_direct_probe(void)
goto fail2;

if (pci_check_type2()) {
- printk(KERN_INFO "PCI: Using configuration type 2\n");
raw_pci_ops = &pci_direct_conf2;
return 2;
}
diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c
index a5ef5f5..b60b2ab 100644
--- a/arch/x86/pci/fixup.c
+++ b/arch/x86/pci/fixup.c
@@ -493,3 +493,20 @@ static void __devinit pci_siemens_interrupt_controller(struct pci_dev *dev)
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015,
pci_siemens_interrupt_controller);
+
+/*
+ * Regular PCI devices have 256 bytes, but AMD Family 10h Opteron ext config
+ * have 4096 bytes. Even if the device is capable, that doesn't mean we can
+ * access it. Maybe we don't have a way to generate extended config space
+ * accesses. So check it
+ */
+static void fam10h_pci_cfg_space_size(struct pci_dev *dev)
+{
+ dev->cfg_size = pci_cfg_space_size_ext(dev, 0);
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1200, fam10h_pci_cfg_space_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1201, fam10h_pci_cfg_space_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1202, fam10h_pci_cfg_space_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1203, fam10h_pci_cfg_space_size);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1204, fam10h_pci_cfg_space_size);
diff --git a/arch/x86/pci/init.c b/arch/x86/pci/init.c
index 3de9f9b..343c363 100644
--- a/arch/x86/pci/init.c
+++ b/arch/x86/pci/init.c
@@ -6,16 +6,13 @@
in the right sequence from here. */
static __init int pci_access_init(void)
{
- int type __maybe_unused = 0;
-
#ifdef CONFIG_PCI_DIRECT
+ int type = 0;
+
type = pci_direct_probe();
#endif
-#ifdef CONFIG_PCI_MMCONFIG
- pci_mmcfg_init(type);
-#endif
- if (raw_pci_ops)
- return 0;
+ pci_mmcfg_early_init();
+
#ifdef CONFIG_PCI_BIOS
pci_pcbios_init();
#endif
@@ -28,7 +25,7 @@ static __init int pci_access_init(void)
#ifdef CONFIG_PCI_DIRECT
pci_direct_init(type);
#endif
- if (!raw_pci_ops)
+ if (!raw_pci_ops && !raw_pci_ext_ops)
printk(KERN_ERR
"PCI: Fatal: No config space access function found\n");

diff --git a/arch/x86/pci/irq.c b/arch/x86/pci/irq.c
index 579745c..0908fca 100644
--- a/arch/x86/pci/irq.c
+++ b/arch/x86/pci/irq.c
@@ -136,9 +136,11 @@ static void __init pirq_peer_trick(void)
busmap[e->bus] = 1;
}
for(i = 1; i < 256; i++) {
+ int node;
if (!busmap[i] || pci_find_bus(0, i))
continue;
- if (pci_scan_bus_with_sysdata(i))
+ node = get_mp_bus_to_node(i);
+ if (pci_scan_bus_on_node(i, &pci_root_ops, node))
printk(KERN_INFO "PCI: Discovered primary peer "
"bus %02x [IRQ]\n", i);
}
diff --git a/arch/x86/pci/k8-bus_64.c b/arch/x86/pci/k8-bus_64.c
index 9cc813e..ab6d4b1 100644
--- a/arch/x86/pci/k8-bus_64.c
+++ b/arch/x86/pci/k8-bus_64.c
@@ -1,83 +1,536 @@
#include <linux/init.h>
#include <linux/pci.h>
+#include <asm/pci-direct.h>
#include <asm/mpspec.h>
#include <linux/cpumask.h>
+#include <linux/topology.h>

/*
* This discovers the pcibus <-> node mapping on AMD K8.
- *
- * RED-PEN need to call this again on PCI hotplug
- * RED-PEN empty cpus get reported wrong
+ * also get peer root bus resource for io,mmio
*/

-#define NODE_ID_REGISTER 0x60
-#define NODE_ID(dword) (dword & 0x07)
-#define LDT_BUS_NUMBER_REGISTER_0 0x94
-#define LDT_BUS_NUMBER_REGISTER_1 0xB4
-#define LDT_BUS_NUMBER_REGISTER_2 0xD4
-#define NR_LDT_BUS_NUMBER_REGISTERS 3
-#define SECONDARY_LDT_BUS_NUMBER(dword) ((dword >> 8) & 0xFF)
-#define SUBORDINATE_LDT_BUS_NUMBER(dword) ((dword >> 16) & 0xFF)
-#define PCI_DEVICE_ID_K8HTCONFIG 0x1100
+
+/*
+ * sub bus (transparent) will use entres from 3 to store extra from root,
+ * so need to make sure have enought slot there, increase PCI_BUS_NUM_RESOURCES?
+ */
+#define RES_NUM 16
+struct pci_root_info {
+ char name[12];
+ unsigned int res_num;
+ struct resource res[RES_NUM];
+ int bus_min;
+ int bus_max;
+ int node;
+ int link;
+};
+
+/* 4 at this time, it may become to 32 */
+#define PCI_ROOT_NR 4
+static int pci_root_num;
+static struct pci_root_info pci_root_info[PCI_ROOT_NR];
+
+#ifdef CONFIG_NUMA
+
+#define BUS_NR 256
+
+static int mp_bus_to_node[BUS_NR];
+
+void set_mp_bus_to_node(int busnum, int node)
+{
+ if (busnum >= 0 && busnum < BUS_NR)
+ mp_bus_to_node[busnum] = node;
+}
+
+int get_mp_bus_to_node(int busnum)
+{
+ int node = -1;
+
+ if (busnum < 0 || busnum > (BUS_NR - 1))
+ return node;
+
+ node = mp_bus_to_node[busnum];
+
+ /*
+ * let numa_node_id to decide it later in dma_alloc_pages
+ * if there is no ram on that node
+ */
+ if (node != -1 && !node_online(node))
+ node = -1;
+
+ return node;
+}
+#endif
+
+void set_pci_bus_resources_arch_default(struct pci_bus *b)
+{
+ int i;
+ int j;
+ struct pci_root_info *info;
+
+ /* if only one root bus, don't need to anything */
+ if (pci_root_num < 2)
+ return;
+
+ for (i = 0; i < pci_root_num; i++) {
+ if (pci_root_info[i].bus_min == b->number)
+ break;
+ }
+
+ if (i == pci_root_num)
+ return;
+
+ info = &pci_root_info[i];
+ for (j = 0; j < info->res_num; j++) {
+ struct resource *res;
+ struct resource *root;
+
+ res = &info->res[j];
+ b->resource[j] = res;
+ if (res->flags & IORESOURCE_IO)
+ root = &ioport_resource;
+ else
+ root = &iomem_resource;
+ insert_resource(root, res);
+ }
+}
+
+#define RANGE_NUM 16
+
+struct res_range {
+ size_t start;
+ size_t end;
+};
+
+static void __init update_range(struct res_range *range, size_t start,
+ size_t end)
+{
+ int i;
+ int j;
+
+ for (j = 0; j < RANGE_NUM; j++) {
+ if (!range[j].end)
+ continue;
+
+ if (start <= range[j].start && end >= range[j].end) {
+ range[j].start = 0;
+ range[j].end = 0;
+ continue;
+ }
+
+ if (start <= range[j].start && end < range[j].end && range[j].start < end + 1) {
+ range[j].start = end + 1;
+ continue;
+ }
+
+
+ if (start > range[j].start && end >= range[j].end && range[j].end > start - 1) {
+ range[j].end = start - 1;
+ continue;
+ }
+
+ if (start > range[j].start && end < range[j].end) {
+ /* find the new spare */
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (range[i].end == 0)
+ break;
+ }
+ if (i < RANGE_NUM) {
+ range[i].end = range[j].end;
+ range[i].start = end + 1;
+ } else {
+ printk(KERN_ERR "run of slot in ranges\n");
+ }
+ range[j].end = start - 1;
+ continue;
+ }
+ }
+}
+
+static void __init update_res(struct pci_root_info *info, size_t start,
+ size_t end, unsigned long flags, int merge)
+{
+ int i;
+ struct resource *res;
+
+ if (!merge)
+ goto addit;
+
+ /* try to merge it with old one */
+ for (i = 0; i < info->res_num; i++) {
+ size_t final_start, final_end;
+ size_t common_start, common_end;
+
+ res = &info->res[i];
+ if (res->flags != flags)
+ continue;
+
+ common_start = max((size_t)res->start, start);
+ common_end = min((size_t)res->end, end);
+ if (common_start > common_end + 1)
+ continue;
+
+ final_start = min((size_t)res->start, start);
+ final_end = max((size_t)res->end, end);
+
+ res->start = final_start;
+ res->end = final_end;
+ return;
+ }
+
+addit:
+
+ /* need to add that */
+ if (info->res_num >= RES_NUM)
+ return;
+
+ res = &info->res[info->res_num];
+ res->name = info->name;
+ res->flags = flags;
+ res->start = start;
+ res->end = end;
+ res->child = NULL;
+ info->res_num++;
+}
+
+struct pci_hostbridge_probe {
+ u32 bus;
+ u32 slot;
+ u32 vendor;
+ u32 device;
+};
+
+static struct pci_hostbridge_probe pci_probes[] __initdata = {
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
+};
+
+static u64 __initdata fam10h_mmconf_start;
+static u64 __initdata fam10h_mmconf_end;
+static void __init get_pci_mmcfg_amd_fam10h_range(void)
+{
+ u32 address;
+ u64 base, msr;
+ unsigned segn_busn_bits;
+
+ /* assume all cpus from fam10h have mmconf */
+ if (boot_cpu_data.x86 < 0x10)
+ return;
+
+ address = MSR_FAM10H_MMIO_CONF_BASE;
+ rdmsrl(address, msr);
+
+ /* mmconfig is not enable */
+ if (!(msr & FAM10H_MMIO_CONF_ENABLE))
+ return;
+
+ base = msr & (FAM10H_MMIO_CONF_BASE_MASK<<FAM10H_MMIO_CONF_BASE_SHIFT);
+
+ segn_busn_bits = (msr >> FAM10H_MMIO_CONF_BUSRANGE_SHIFT) &
+ FAM10H_MMIO_CONF_BUSRANGE_MASK;
+
+ fam10h_mmconf_start = base;
+ fam10h_mmconf_end = base + (1ULL<<(segn_busn_bits + 20)) - 1;
+}

/**
- * fill_mp_bus_to_cpumask()
+ * early_fill_mp_bus_to_node()
+ * called before pcibios_scan_root and pci_scan_bus
* fills the mp_bus_to_cpumask array based according to the LDT Bus Number
* Registers found in the K8 northbridge
*/
-__init static int
-fill_mp_bus_to_cpumask(void)
+static int __init early_fill_mp_bus_info(void)
{
- struct pci_dev *nb_dev = NULL;
- int i, j;
- u32 ldtbus, nid;
- static int lbnr[3] = {
- LDT_BUS_NUMBER_REGISTER_0,
- LDT_BUS_NUMBER_REGISTER_1,
- LDT_BUS_NUMBER_REGISTER_2
- };
-
- while ((nb_dev = pci_get_device(PCI_VENDOR_ID_AMD,
- PCI_DEVICE_ID_K8HTCONFIG, nb_dev))) {
- pci_read_config_dword(nb_dev, NODE_ID_REGISTER, &nid);
-
- for (i = 0; i < NR_LDT_BUS_NUMBER_REGISTERS; i++) {
- pci_read_config_dword(nb_dev, lbnr[i], &ldtbus);
- /*
- * if there are no busses hanging off of the current
- * ldt link then both the secondary and subordinate
- * bus number fields are set to 0.
- *
- * RED-PEN
- * This is slightly broken because it assumes
- * HT node IDs == Linux node ids, which is not always
- * true. However it is probably mostly true.
- */
- if (!(SECONDARY_LDT_BUS_NUMBER(ldtbus) == 0
- && SUBORDINATE_LDT_BUS_NUMBER(ldtbus) == 0)) {
- for (j = SECONDARY_LDT_BUS_NUMBER(ldtbus);
- j <= SUBORDINATE_LDT_BUS_NUMBER(ldtbus);
- j++) {
- struct pci_bus *bus;
- struct pci_sysdata *sd;
-
- long node = NODE_ID(nid);
- /* Algorithm a bit dumb, but
- it shouldn't matter here */
- bus = pci_find_bus(0, j);
- if (!bus)
- continue;
- if (!node_online(node))
- node = 0;
-
- sd = bus->sysdata;
- sd->node = node;
- }
+ int i;
+ int j;
+ unsigned bus;
+ unsigned slot;
+ int found;
+ int node;
+ int link;
+ int def_node;
+ int def_link;
+ struct pci_root_info *info;
+ u32 reg;
+ struct resource *res;
+ size_t start;
+ size_t end;
+ struct res_range range[RANGE_NUM];
+ u64 val;
+ u32 address;
+
+#ifdef CONFIG_NUMA
+ for (i = 0; i < BUS_NR; i++)
+ mp_bus_to_node[i] = -1;
+#endif
+
+ if (!early_pci_allowed())
+ return -1;
+
+ found = 0;
+ for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+ u32 id;
+ u16 device;
+ u16 vendor;
+
+ bus = pci_probes[i].bus;
+ slot = pci_probes[i].slot;
+ id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
+
+ vendor = id & 0xffff;
+ device = (id>>16) & 0xffff;
+ if (pci_probes[i].vendor == vendor &&
+ pci_probes[i].device == device) {
+ found = 1;
+ break;
+ }
+ }
+
+ if (!found)
+ return 0;
+
+ pci_root_num = 0;
+ for (i = 0; i < 4; i++) {
+ int min_bus;
+ int max_bus;
+ reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
+
+ /* Check if that register is enabled for bus range */
+ if ((reg & 7) != 3)
+ continue;
+
+ min_bus = (reg >> 16) & 0xff;
+ max_bus = (reg >> 24) & 0xff;
+ node = (reg >> 4) & 0x07;
+#ifdef CONFIG_NUMA
+ for (j = min_bus; j <= max_bus; j++)
+ mp_bus_to_node[j] = (unsigned char) node;
+#endif
+ link = (reg >> 8) & 0x03;
+
+ info = &pci_root_info[pci_root_num];
+ info->bus_min = min_bus;
+ info->bus_max = max_bus;
+ info->node = node;
+ info->link = link;
+ sprintf(info->name, "PCI Bus #%02x", min_bus);
+ pci_root_num++;
+ }
+
+ /* get the default node and link for left over res */
+ reg = read_pci_config(bus, slot, 0, 0x60);
+ def_node = (reg >> 8) & 0x07;
+ reg = read_pci_config(bus, slot, 0, 0x64);
+ def_link = (reg >> 8) & 0x03;
+
+ memset(range, 0, sizeof(range));
+ range[0].end = 0xffff;
+ /* io port resource */
+ for (i = 0; i < 4; i++) {
+ reg = read_pci_config(bus, slot, 1, 0xc0 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = reg & 0xfff000;
+ reg = read_pci_config(bus, slot, 1, 0xc4 + (i << 3));
+ node = reg & 0x07;
+ link = (reg >> 4) & 0x03;
+ end = (reg & 0xfff000) | 0xfff;
+
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == node && info->link == link)
+ break;
+ }
+ if (j == pci_root_num)
+ continue; /* not found */
+
+ info = &pci_root_info[j];
+ printk(KERN_DEBUG "node %d link %d: io port [%llx, %llx]\n",
+ node, link, (u64)start, (u64)end);
+
+ /* kernel only handle 16 bit only */
+ if (end > 0xffff)
+ end = 0xffff;
+ update_res(info, start, end, IORESOURCE_IO, 1);
+ update_range(range, start, end);
+ }
+ /* add left over io port range to def node/link, [0, 0xffff] */
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == def_node && info->link == def_link)
+ break;
+ }
+ if (j < pci_root_num) {
+ info = &pci_root_info[j];
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (!range[i].end)
+ continue;
+
+ update_res(info, range[i].start, range[i].end,
+ IORESOURCE_IO, 1);
+ }
+ }
+
+ memset(range, 0, sizeof(range));
+ /* 0xfd00000000-0xffffffffff for HT */
+ range[0].end = (0xfdULL<<32) - 1;
+
+ /* need to take out [0, TOM) for RAM*/
+ address = MSR_K8_TOP_MEM1;
+ rdmsrl(address, val);
+ end = (val & 0xffffff8000000ULL);
+ printk(KERN_INFO "TOM: %016lx aka %ldM\n", end, end>>20);
+ if (end < (1ULL<<32))
+ update_range(range, 0, end - 1);
+
+ /* get mmconfig */
+ get_pci_mmcfg_amd_fam10h_range();
+ /* need to take out mmconf range */
+ if (fam10h_mmconf_end) {
+ printk(KERN_DEBUG "Fam 10h mmconf [%llx, %llx]\n", fam10h_mmconf_start, fam10h_mmconf_end);
+ update_range(range, fam10h_mmconf_start, fam10h_mmconf_end);
+ }
+
+ /* mmio resource */
+ for (i = 0; i < 8; i++) {
+ reg = read_pci_config(bus, slot, 1, 0x80 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = reg & 0xffffff00; /* 39:16 on 31:8*/
+ start <<= 8;
+ reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
+ node = reg & 0x07;
+ link = (reg >> 4) & 0x03;
+ end = (reg & 0xffffff00);
+ end <<= 8;
+ end |= 0xffff;
+
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == node && info->link == link)
+ break;
+ }
+ if (j == pci_root_num)
+ continue; /* not found */
+
+ info = &pci_root_info[j];
+
+ printk(KERN_DEBUG "node %d link %d: mmio [%llx, %llx]",
+ node, link, (u64)start, (u64)end);
+ /*
+ * some sick allocation would have range overlap with fam10h
+ * mmconf range, so need to update start and end.
+ */
+ if (fam10h_mmconf_end) {
+ int changed = 0;
+ u64 endx = 0;
+ if (start >= fam10h_mmconf_start &&
+ start <= fam10h_mmconf_end) {
+ start = fam10h_mmconf_end + 1;
+ changed = 1;
+ }
+
+ if (end >= fam10h_mmconf_start &&
+ end <= fam10h_mmconf_end) {
+ end = fam10h_mmconf_start - 1;
+ changed = 1;
+ }
+
+ if (start < fam10h_mmconf_start &&
+ end > fam10h_mmconf_end) {
+ /* we got a hole */
+ endx = fam10h_mmconf_start - 1;
+ update_res(info, start, endx, IORESOURCE_MEM, 0);
+ update_range(range, start, endx);
+ printk(KERN_CONT " ==> [%llx, %llx]", (u64)start, endx);
+ start = fam10h_mmconf_end + 1;
+ changed = 1;
+ }
+ if (changed) {
+ if (start <= end) {
+ printk(KERN_CONT " %s [%llx, %llx]", endx?"and":"==>", (u64)start, (u64)end);
+ } else {
+ printk(KERN_CONT "%s\n", endx?"":" ==> none");
+ continue;
+ }
}
}
+
+ update_res(info, start, end, IORESOURCE_MEM, 1);
+ update_range(range, start, end);
+ printk(KERN_CONT "\n");
+ }
+
+ /* need to take out [4G, TOM2) for RAM*/
+ /* SYS_CFG */
+ address = MSR_K8_SYSCFG;
+ rdmsrl(address, val);
+ /* TOP_MEM2 is enabled? */
+ if (val & (1<<21)) {
+ /* TOP_MEM2 */
+ address = MSR_K8_TOP_MEM2;
+ rdmsrl(address, val);
+ end = (val & 0xffffff8000000ULL);
+ printk(KERN_INFO "TOM2: %016lx aka %ldM\n", end, end>>20);
+ update_range(range, 1ULL<<32, end - 1);
+ }
+
+ /*
+ * add left over mmio range to def node/link ?
+ * that is tricky, just record range in from start_min to 4G
+ */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == def_node && info->link == def_link)
+ break;
+ }
+ if (j < pci_root_num) {
+ info = &pci_root_info[j];
+
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (!range[i].end)
+ continue;
+
+ update_res(info, range[i].start, range[i].end,
+ IORESOURCE_MEM, 1);
+ }
+ }
+
+#ifdef CONFIG_NUMA
+ for (i = 0; i < BUS_NR; i++) {
+ node = mp_bus_to_node[i];
+ if (node >= 0)
+ printk(KERN_DEBUG "bus: %02x to node: %02x\n", i, node);
+ }
+#endif
+
+ for (i = 0; i < pci_root_num; i++) {
+ int res_num;
+ int busnum;
+
+ info = &pci_root_info[i];
+ res_num = info->res_num;
+ busnum = info->bus_min;
+ printk(KERN_DEBUG "bus: [%02x,%02x] on node %x link %x\n",
+ info->bus_min, info->bus_max, info->node, info->link);
+ for (j = 0; j < res_num; j++) {
+ res = &info->res[j];
+ printk(KERN_DEBUG "bus: %02x index %x %s: [%llx, %llx]\n",
+ busnum, j,
+ (res->flags & IORESOURCE_IO)?"io port":"mmio",
+ res->start, res->end);
+ }
}

return 0;
}

-fs_initcall(fill_mp_bus_to_cpumask);
+postcore_initcall(early_fill_mp_bus_info);
diff --git a/arch/x86/pci/legacy.c b/arch/x86/pci/legacy.c
index e041ced..a67921c 100644
--- a/arch/x86/pci/legacy.c
+++ b/arch/x86/pci/legacy.c
@@ -12,6 +12,7 @@
static void __devinit pcibios_fixup_peer_bridges(void)
{
int n, devfn;
+ long node;

if (pcibios_last_bus <= 0 || pcibios_last_bus >= 0xff)
return;
@@ -21,12 +22,13 @@ static void __devinit pcibios_fixup_peer_bridges(void)
u32 l;
if (pci_find_bus(0, n))
continue;
+ node = get_mp_bus_to_node(n);
for (devfn = 0; devfn < 256; devfn += 8) {
if (!raw_pci_read(0, n, devfn, PCI_VENDOR_ID, 2, &l) &&
l != 0x0000 && l != 0xffff) {
DBG("Found device at %02x:%02x [%04x]\n", n, devfn, l);
printk(KERN_INFO "PCI: Discovered peer bus %02x\n", n);
- pci_scan_bus_with_sysdata(n);
+ pci_scan_bus_on_node(n, &pci_root_ops, node);
break;
}
}
diff --git a/arch/x86/pci/mmconfig-shared.c b/arch/x86/pci/mmconfig-shared.c
index 8d54df4..0cfebec 100644
--- a/arch/x86/pci/mmconfig-shared.c
+++ b/arch/x86/pci/mmconfig-shared.c
@@ -28,7 +28,7 @@ static int __initdata pci_mmcfg_resources_inserted;
static const char __init *pci_mmcfg_e7520(void)
{
u32 win;
- pci_direct_conf1.read(0, 0, PCI_DEVFN(0,0), 0xce, 2, &win);
+ raw_pci_ops->read(0, 0, PCI_DEVFN(0, 0), 0xce, 2, &win);

win = win & 0xf000;
if(win == 0x0000 || win == 0xf000)
@@ -53,7 +53,7 @@ static const char __init *pci_mmcfg_intel_945(void)

pci_mmcfg_config_num = 1;

- pci_direct_conf1.read(0, 0, PCI_DEVFN(0,0), 0x48, 4, &pciexbar);
+ raw_pci_ops->read(0, 0, PCI_DEVFN(0, 0), 0x48, 4, &pciexbar);

/* Enable bit */
if (!(pciexbar & 1))
@@ -100,33 +100,102 @@ static const char __init *pci_mmcfg_intel_945(void)
return "Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub";
}

+static const char __init *pci_mmcfg_amd_fam10h(void)
+{
+ u32 low, high, address;
+ u64 base, msr;
+ int i;
+ unsigned segnbits = 0, busnbits;
+
+ if (!(pci_probe & PCI_CHECK_ENABLE_AMD_MMCONF))
+ return NULL;
+
+ address = MSR_FAM10H_MMIO_CONF_BASE;
+ if (rdmsr_safe(address, &low, &high))
+ return NULL;
+
+ msr = high;
+ msr <<= 32;
+ msr |= low;
+
+ /* mmconfig is not enable */
+ if (!(msr & FAM10H_MMIO_CONF_ENABLE))
+ return NULL;
+
+ base = msr & (FAM10H_MMIO_CONF_BASE_MASK<<FAM10H_MMIO_CONF_BASE_SHIFT);
+
+ busnbits = (msr >> FAM10H_MMIO_CONF_BUSRANGE_SHIFT) &
+ FAM10H_MMIO_CONF_BUSRANGE_MASK;
+
+ /*
+ * only handle bus 0 ?
+ * need to skip it
+ */
+ if (!busnbits)
+ return NULL;
+
+ if (busnbits > 8) {
+ segnbits = busnbits - 8;
+ busnbits = 8;
+ }
+
+ pci_mmcfg_config_num = (1 << segnbits);
+ pci_mmcfg_config = kzalloc(sizeof(pci_mmcfg_config[0]) *
+ pci_mmcfg_config_num, GFP_KERNEL);
+ if (!pci_mmcfg_config)
+ return NULL;
+
+ for (i = 0; i < (1 << segnbits); i++) {
+ pci_mmcfg_config[i].address = base + (1<<28) * i;
+ pci_mmcfg_config[i].pci_segment = i;
+ pci_mmcfg_config[i].start_bus_number = 0;
+ pci_mmcfg_config[i].end_bus_number = (1 << busnbits) - 1;
+ }
+
+ return "AMD Family 10h NB";
+}
+
struct pci_mmcfg_hostbridge_probe {
+ u32 bus;
+ u32 devfn;
u32 vendor;
u32 device;
const char *(*probe)(void);
};

static struct pci_mmcfg_hostbridge_probe pci_mmcfg_probes[] __initdata = {
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, pci_mmcfg_e7520 },
- { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82945G_HB, pci_mmcfg_intel_945 },
+ { 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID_INTEL,
+ PCI_DEVICE_ID_INTEL_E7520_MCH, pci_mmcfg_e7520 },
+ { 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID_INTEL,
+ PCI_DEVICE_ID_INTEL_82945G_HB, pci_mmcfg_intel_945 },
+ { 0, PCI_DEVFN(0x18, 0), PCI_VENDOR_ID_AMD,
+ 0x1200, pci_mmcfg_amd_fam10h },
+ { 0xff, PCI_DEVFN(0, 0), PCI_VENDOR_ID_AMD,
+ 0x1200, pci_mmcfg_amd_fam10h },
};

static int __init pci_mmcfg_check_hostbridge(void)
{
u32 l;
+ u32 bus, devfn;
u16 vendor, device;
int i;
const char *name;

- pci_direct_conf1.read(0, 0, PCI_DEVFN(0,0), 0, 4, &l);
- vendor = l & 0xffff;
- device = (l >> 16) & 0xffff;
+ if (!raw_pci_ops)
+ return 0;

pci_mmcfg_config_num = 0;
pci_mmcfg_config = NULL;
name = NULL;

for (i = 0; !name && i < ARRAY_SIZE(pci_mmcfg_probes); i++) {
+ bus = pci_mmcfg_probes[i].bus;
+ devfn = pci_mmcfg_probes[i].devfn;
+ raw_pci_ops->read(0, bus, devfn, 0, 4, &l);
+ vendor = l & 0xffff;
+ device = (l >> 16) & 0xffff;
+
if (pci_mmcfg_probes[i].vendor == vendor &&
pci_mmcfg_probes[i].device == device)
name = pci_mmcfg_probes[i].probe();
@@ -173,9 +242,78 @@ static void __init pci_mmcfg_insert_resources(unsigned long resource_flags)
pci_mmcfg_resources_inserted = 1;
}

-static void __init pci_mmcfg_reject_broken(int type)
+static acpi_status __init check_mcfg_resource(struct acpi_resource *res,
+ void *data)
+{
+ struct resource *mcfg_res = data;
+ struct acpi_resource_address64 address;
+ acpi_status status;
+
+ if (res->type == ACPI_RESOURCE_TYPE_FIXED_MEMORY32) {
+ struct acpi_resource_fixed_memory32 *fixmem32 =
+ &res->data.fixed_memory32;
+ if (!fixmem32)
+ return AE_OK;
+ if ((mcfg_res->start >= fixmem32->address) &&
+ (mcfg_res->end < (fixmem32->address +
+ fixmem32->address_length))) {
+ mcfg_res->flags = 1;
+ return AE_CTRL_TERMINATE;
+ }
+ }
+ if ((res->type != ACPI_RESOURCE_TYPE_ADDRESS32) &&
+ (res->type != ACPI_RESOURCE_TYPE_ADDRESS64))
+ return AE_OK;
+
+ status = acpi_resource_to_address64(res, &address);
+ if (ACPI_FAILURE(status) ||
+ (address.address_length <= 0) ||
+ (address.resource_type != ACPI_MEMORY_RANGE))
+ return AE_OK;
+
+ if ((mcfg_res->start >= address.minimum) &&
+ (mcfg_res->end < (address.minimum + address.address_length))) {
+ mcfg_res->flags = 1;
+ return AE_CTRL_TERMINATE;
+ }
+ return AE_OK;
+}
+
+static acpi_status __init find_mboard_resource(acpi_handle handle, u32 lvl,
+ void *context, void **rv)
+{
+ struct resource *mcfg_res = context;
+
+ acpi_walk_resources(handle, METHOD_NAME__CRS,
+ check_mcfg_resource, context);
+
+ if (mcfg_res->flags)
+ return AE_CTRL_TERMINATE;
+
+ return AE_OK;
+}
+
+static int __init is_acpi_reserved(unsigned long start, unsigned long end)
+{
+ struct resource mcfg_res;
+
+ mcfg_res.start = start;
+ mcfg_res.end = end;
+ mcfg_res.flags = 0;
+
+ acpi_get_devices("PNP0C01", find_mboard_resource, &mcfg_res, NULL);
+
+ if (!mcfg_res.flags)
+ acpi_get_devices("PNP0C02", find_mboard_resource, &mcfg_res,
+ NULL);
+
+ return mcfg_res.flags;
+}
+
+static void __init pci_mmcfg_reject_broken(int early)
{
typeof(pci_mmcfg_config[0]) *cfg;
+ int i;

if ((pci_mmcfg_config_num == 0) ||
(pci_mmcfg_config == NULL) ||
@@ -184,51 +322,80 @@ static void __init pci_mmcfg_reject_broken(int type)

cfg = &pci_mmcfg_config[0];

- /*
- * Handle more broken MCFG tables on Asus etc.
- * They only contain a single entry for bus 0-0.
- */
- if (pci_mmcfg_config_num == 1 &&
- cfg->pci_segment == 0 &&
- (cfg->start_bus_number | cfg->end_bus_number) == 0) {
- printk(KERN_ERR "PCI: start and end of bus number is 0. "
- "Rejected as broken MCFG.\n");
- goto reject;
+ for (i = 0; i < pci_mmcfg_config_num; i++) {
+ int valid = 0;
+ u32 size = (cfg->end_bus_number + 1) << 20;
+ cfg = &pci_mmcfg_config[i];
+ printk(KERN_NOTICE "PCI: MCFG configuration %d: base %lx "
+ "segment %hu buses %u - %u\n",
+ i, (unsigned long)cfg->address, cfg->pci_segment,
+ (unsigned int)cfg->start_bus_number,
+ (unsigned int)cfg->end_bus_number);
+
+ if (!early &&
+ is_acpi_reserved(cfg->address, cfg->address + size - 1)) {
+ printk(KERN_NOTICE "PCI: MCFG area at %Lx reserved "
+ "in ACPI motherboard resources\n",
+ cfg->address);
+ valid = 1;
+ }
+
+ if (valid)
+ continue;
+
+ if (!early)
+ printk(KERN_ERR "PCI: BIOS Bug: MCFG area at %Lx is not"
+ " reserved in ACPI motherboard resources\n",
+ cfg->address);
+ /* Don't try to do this check unless configuration
+ type 1 is available. how about type 2 ?*/
+ if (raw_pci_ops && e820_all_mapped(cfg->address,
+ cfg->address + size - 1,
+ E820_RESERVED)) {
+ printk(KERN_NOTICE
+ "PCI: MCFG area at %Lx reserved in E820\n",
+ cfg->address);
+ valid = 1;
+ }
+
+ if (!valid)
+ goto reject;
}

- /*
- * Only do this check when type 1 works. If it doesn't work
- * assume we run on a Mac and always use MCFG
- */
- if (type == 1 && !e820_all_mapped(cfg->address,
- cfg->address + MMCONFIG_APER_MIN,
- E820_RESERVED)) {
- printk(KERN_ERR "PCI: BIOS Bug: MCFG area at %Lx is not"
- " E820-reserved\n", cfg->address);
- goto reject;
- }
return;

reject:
printk(KERN_ERR "PCI: Not using MMCONFIG.\n");
+ pci_mmcfg_arch_free();
kfree(pci_mmcfg_config);
pci_mmcfg_config = NULL;
pci_mmcfg_config_num = 0;
}

-void __init pci_mmcfg_init(int type)
-{
- int known_bridge = 0;
+static int __initdata known_bridge;

+void __init __pci_mmcfg_init(int early)
+{
+ /* MMCONFIG disabled */
if ((pci_probe & PCI_PROBE_MMCONF) == 0)
return;

- if (type == 1 && pci_mmcfg_check_hostbridge())
- known_bridge = 1;
+ /* MMCONFIG already enabled */
+ if (!early && !(pci_probe & PCI_PROBE_MASK & ~PCI_PROBE_MMCONF))
+ return;
+
+ /* for late to exit */
+ if (known_bridge)
+ return;
+
+ if (early) {
+ if (pci_mmcfg_check_hostbridge())
+ known_bridge = 1;
+ }

if (!known_bridge) {
acpi_table_parse(ACPI_SIG_MCFG, acpi_parse_mcfg);
- pci_mmcfg_reject_broken(type);
+ pci_mmcfg_reject_broken(early);
}

if ((pci_mmcfg_config_num == 0) ||
@@ -249,6 +416,16 @@ void __init pci_mmcfg_init(int type)
}
}

+void __init pci_mmcfg_early_init(void)
+{
+ __pci_mmcfg_init(1);
+}
+
+void __init pci_mmcfg_late_init(void)
+{
+ __pci_mmcfg_init(0);
+}
+
static int __init pci_mmcfg_late_insert_resources(void)
{
/*
diff --git a/arch/x86/pci/mmconfig_32.c b/arch/x86/pci/mmconfig_32.c
index 081816a..f3c761d 100644
--- a/arch/x86/pci/mmconfig_32.c
+++ b/arch/x86/pci/mmconfig_32.c
@@ -136,3 +136,7 @@ int __init pci_mmcfg_arch_init(void)
raw_pci_ext_ops = &pci_mmcfg;
return 1;
}
+
+void __init pci_mmcfg_arch_free(void)
+{
+}
diff --git a/arch/x86/pci/mmconfig_64.c b/arch/x86/pci/mmconfig_64.c
index 9207fd4..a199416 100644
--- a/arch/x86/pci/mmconfig_64.c
+++ b/arch/x86/pci/mmconfig_64.c
@@ -127,7 +127,7 @@ static void __iomem * __init mcfg_ioremap(struct acpi_mcfg_allocation *cfg)
int __init pci_mmcfg_arch_init(void)
{
int i;
- pci_mmcfg_virt = kmalloc(sizeof(*pci_mmcfg_virt) *
+ pci_mmcfg_virt = kzalloc(sizeof(*pci_mmcfg_virt) *
pci_mmcfg_config_num, GFP_KERNEL);
if (pci_mmcfg_virt == NULL) {
printk(KERN_ERR "PCI: Can not allocate memory for mmconfig structures\n");
@@ -141,9 +141,29 @@ int __init pci_mmcfg_arch_init(void)
printk(KERN_ERR "PCI: Cannot map mmconfig aperture for "
"segment %d\n",
pci_mmcfg_config[i].pci_segment);
+ pci_mmcfg_arch_free();
return 0;
}
}
raw_pci_ext_ops = &pci_mmcfg;
return 1;
}
+
+void __init pci_mmcfg_arch_free(void)
+{
+ int i;
+
+ if (pci_mmcfg_virt == NULL)
+ return;
+
+ for (i = 0; i < pci_mmcfg_config_num; ++i) {
+ if (pci_mmcfg_virt[i].virt) {
+ iounmap(pci_mmcfg_virt[i].virt);
+ pci_mmcfg_virt[i].virt = NULL;
+ pci_mmcfg_virt[i].cfg = NULL;
+ }
+ }
+
+ kfree(pci_mmcfg_virt);
+ pci_mmcfg_virt = NULL;
+}
diff --git a/arch/x86/pci/mp_bus_to_node.c b/arch/x86/pci/mp_bus_to_node.c
new file mode 100644
index 0000000..0229439
--- /dev/null
+++ b/arch/x86/pci/mp_bus_to_node.c
@@ -0,0 +1,23 @@
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/topology.h>
+
+#define BUS_NR 256
+
+static unsigned char mp_bus_to_node[BUS_NR];
+
+void set_mp_bus_to_node(int busnum, int node)
+{
+ if (busnum >= 0 && busnum < BUS_NR)
+ mp_bus_to_node[busnum] = (unsigned char) node;
+}
+
+int get_mp_bus_to_node(int busnum)
+{
+ int node;
+
+ if (busnum < 0 || busnum > (BUS_NR - 1))
+ return 0;
+ node = mp_bus_to_node[busnum];
+ return node;
+}
diff --git a/arch/x86/pci/pci.h b/arch/x86/pci/pci.h
index c4bddae..8ef86b5 100644
--- a/arch/x86/pci/pci.h
+++ b/arch/x86/pci/pci.h
@@ -26,6 +26,7 @@
#define PCI_ASSIGN_ALL_BUSSES 0x4000
#define PCI_CAN_SKIP_ISA_ALIGN 0x8000
#define PCI_USE__CRS 0x10000
+#define PCI_CHECK_ENABLE_AMD_MMCONF 0x20000

extern unsigned int pci_probe;
extern unsigned long pirq_table_addr;
@@ -97,11 +98,11 @@ extern struct pci_raw_ops pci_direct_conf1;
extern int pci_direct_probe(void);
extern void pci_direct_init(int type);
extern void pci_pcbios_init(void);
-extern void pci_mmcfg_init(int type);

/* pci-mmconfig.c */

extern int __init pci_mmcfg_arch_init(void);
+extern void __init pci_mmcfg_arch_free(void);

/*
* AMD Fam10h CPUs are buggy, and cannot access MMIO config space
diff --git a/drivers/acpi/bus.c b/drivers/acpi/bus.c
index 2d1955c..a6dbcf4 100644
--- a/drivers/acpi/bus.c
+++ b/drivers/acpi/bus.c
@@ -35,6 +35,7 @@
#ifdef CONFIG_X86
#include <asm/mpspec.h>
#endif
+#include <linux/pci.h>
#include <acpi/acpi_bus.h>
#include <acpi/acpi_drivers.h>

@@ -784,6 +785,7 @@ static int __init acpi_init(void)
result = acpi_bus_init();

if (!result) {
+ pci_mmcfg_late_init();
if (!(pm_flags & PM_APM))
pm_flags |= PM_ACPI;
else {
diff --git a/drivers/base/core.c b/drivers/base/core.c
index 9248e09..be288b5 100644
--- a/drivers/base/core.c
+++ b/drivers/base/core.c
@@ -787,6 +787,10 @@ int device_add(struct device *dev)
parent = get_device(dev->parent);
setup_parent(dev, parent);

+ /* use parent numa_node */
+ if (parent)
+ set_dev_node(dev, dev_to_node(parent));
+
/* first, register with generic layer. */
error = kobject_add(&dev->kobj, dev->kobj.parent, "%s", dev->bus_id);
if (error)
@@ -1306,8 +1310,11 @@ int device_move(struct device *dev, struct device *new_parent)
dev->parent = new_parent;
if (old_parent)
klist_remove(&dev->knode_parent);
- if (new_parent)
+ if (new_parent) {
klist_add_tail(&dev->knode_parent, &new_parent->klist_children);
+ set_dev_node(dev, dev_to_node(new_parent));
+ }
+
if (!dev->class)
goto out_put;
error = device_move_class_links(dev, old_parent, new_parent);
@@ -1317,9 +1324,12 @@ int device_move(struct device *dev, struct device *new_parent)
if (!kobject_move(&dev->kobj, &old_parent->kobj)) {
if (new_parent)
klist_remove(&dev->knode_parent);
- if (old_parent)
+ dev->parent = old_parent;
+ if (old_parent) {
klist_add_tail(&dev->knode_parent,
&old_parent->klist_children);
+ set_dev_node(dev, dev_to_node(old_parent));
+ }
}
cleanup_glue_dir(dev, new_parent_kobj);
put_device(new_parent);
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index f991359..4a55bf3 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -842,11 +842,14 @@ static void set_pcie_port_type(struct pci_dev *pdev)
* reading the dword at 0x100 which must either be 0 or a valid extended
* capability header.
*/
-int pci_cfg_space_size(struct pci_dev *dev)
+int pci_cfg_space_size_ext(struct pci_dev *dev, unsigned check_exp_pcix)
{
int pos;
u32 status;

+ if (!check_exp_pcix)
+ goto skip;
+
pos = pci_find_capability(dev, PCI_CAP_ID_EXP);
if (!pos) {
pos = pci_find_capability(dev, PCI_CAP_ID_PCIX);
@@ -858,6 +861,7 @@ int pci_cfg_space_size(struct pci_dev *dev)
goto fail;
}

+ skip:
if (pci_read_config_dword(dev, 256, &status) != PCIBIOS_SUCCESSFUL)
goto fail;
if (status == 0xffffffff)
@@ -869,6 +873,11 @@ int pci_cfg_space_size(struct pci_dev *dev)
return PCI_CFG_SPACE_SIZE;
}

+int pci_cfg_space_size(struct pci_dev *dev)
+{
+ return pci_cfg_space_size_ext(dev, 1);
+}
+
static void pci_release_bus_bridge_dev(struct device *dev)
{
kfree(dev);
@@ -964,7 +973,6 @@ void pci_device_add(struct pci_dev *dev, struct pci_bus *bus)
dev->dev.release = pci_release_dev;
pci_dev_get(dev);

- set_dev_node(&dev->dev, pcibus_to_node(bus));
dev->dev.dma_mask = &dev->dma_mask;
dev->dev.dma_parms = &dev->dma_parms;
dev->dev.coherent_dma_mask = 0xffffffffull;
@@ -1080,6 +1088,10 @@ unsigned int __devinit pci_scan_child_bus(struct pci_bus *bus)
return max;
}

+void __attribute__((weak)) set_pci_bus_resources_arch_default(struct pci_bus *b)
+{
+}
+
struct pci_bus * pci_create_bus(struct device *parent,
int bus, struct pci_ops *ops, void *sysdata)
{
@@ -1119,6 +1131,9 @@ struct pci_bus * pci_create_bus(struct device *parent,
goto dev_reg_err;
b->bridge = get_device(dev);

+ if (!parent)
+ set_dev_node(b->bridge, pcibus_to_node(b));
+
b->dev.class = &pcibus_class;
b->dev.parent = b->bridge;
sprintf(b->dev.bus_id, "%04x:%02x", pci_domain_nr(b), bus);
@@ -1136,6 +1151,8 @@ struct pci_bus * pci_create_bus(struct device *parent,
b->resource[0] = &ioport_resource;
b->resource[1] = &iomem_resource;

+ set_pci_bus_resources_arch_default(b);
+
return b;

dev_create_file_err:
diff --git a/include/asm-x86/pci.h b/include/asm-x86/pci.h
index ddd8e24..30bbde0 100644
--- a/include/asm-x86/pci.h
+++ b/include/asm-x86/pci.h
@@ -19,6 +19,8 @@ struct pci_sysdata {
};

/* scan a bus after allocating a pci_sysdata for it */
+extern struct pci_bus *pci_scan_bus_on_node(int busno, struct pci_ops *ops,
+ int node);
extern struct pci_bus *pci_scan_bus_with_sysdata(int busno);

static inline int pci_domain_nr(struct pci_bus *bus)
diff --git a/include/asm-x86/topology.h b/include/asm-x86/topology.h
index 2207326..0e6d6b0 100644
--- a/include/asm-x86/topology.h
+++ b/include/asm-x86/topology.h
@@ -193,9 +193,25 @@ extern cpumask_t cpu_coregroup_map(int cpu);
#define topology_thread_siblings(cpu) (per_cpu(cpu_sibling_map, cpu))
#endif

+struct pci_bus;
+void set_pci_bus_resources_arch_default(struct pci_bus *b);
+
#ifdef CONFIG_SMP
#define mc_capable() (boot_cpu_data.x86_max_cores > 1)
#define smt_capable() (smp_num_siblings > 1)
#endif

+#ifdef CONFIG_NUMA
+extern int get_mp_bus_to_node(int busnum);
+extern void set_mp_bus_to_node(int busnum, int node);
+#else
+static inline int get_mp_bus_to_node(int busnum)
+{
+ return 0;
+}
+static inline void set_mp_bus_to_node(int busnum, int node)
+{
+}
+#endif
+
#endif
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 2c7e003..41f7ce7 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -79,6 +79,7 @@ typedef int (*acpi_table_handler) (struct acpi_table_header *table);
typedef int (*acpi_table_entry_handler) (struct acpi_subtable_header *header, const unsigned long end);

char * __acpi_map_table (unsigned long phys_addr, unsigned long size);
+int early_acpi_boot_init(void);
int acpi_boot_init (void);
int acpi_boot_table_init (void);
int acpi_numa_init (void);
@@ -235,6 +236,10 @@ int acpi_check_mem_region(resource_size_t start, resource_size_t n,

#else /* CONFIG_ACPI */

+static inline int early_acpi_boot_init(void)
+{
+ return 0;
+}
static inline int acpi_boot_init(void)
{
return 0;
diff --git a/include/linux/pci.h b/include/linux/pci.h
index 2924913..abc998f 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -254,7 +254,7 @@ static inline void pci_add_saved_cap(struct pci_dev *pci_dev,
#define PCI_NUM_RESOURCES 11

#ifndef PCI_BUS_NUM_RESOURCES
-#define PCI_BUS_NUM_RESOURCES 8
+#define PCI_BUS_NUM_RESOURCES 16
#endif

#define PCI_REGION_FLAG_MASK 0x0fU /* These bits of resource flags tell us the PCI region flags */
@@ -666,6 +666,7 @@ int pci_scan_bridge(struct pci_bus *bus, struct pci_dev *dev, int max,

void pci_walk_bus(struct pci_bus *top, void (*cb)(struct pci_dev *, void *),
void *userdata);
+int pci_cfg_space_size_ext(struct pci_dev *dev, unsigned check_exp_pcix);
int pci_cfg_space_size(struct pci_dev *dev);
unsigned char pci_bus_max_busnr(struct pci_bus *bus);

@@ -1053,5 +1054,13 @@ extern unsigned long pci_cardbus_mem_size;

extern int pcibios_add_platform_entries(struct pci_dev *dev);

+#ifdef CONFIG_PCI_MMCONFIG
+extern void __init pci_mmcfg_early_init(void);
+extern void __init pci_mmcfg_late_init(void);
+#else
+static inline void pci_mmcfg_early_init(void) { }
+static inline void pci_mmcfg_late_init(void) { }
+#endif
+
#endif /* __KERNEL__ */
#endif /* LINUX_PCI_H */

\
 
 \ /
  Last update: 2008-04-26 23:59    [W:0.297 / U:1.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site