Messages in this thread | | | From | Yuval Hager <> | Subject | Re: BCM4312 Fails when xdm is started | Date | Mon, 24 Nov 2008 10:49:38 +0200 |
| |
On Sunday 23 November 2008, Larry Finger wrote: > From a config file posted earlier, the OP is using SLAB. Is there any point > in trying SLUB?
Another try, not sure what it means:
* Added CONFIG_SLUB and CONFIG_SLUB_DEBUG
* boot parameters: root=/dev/sda3 debug memory_corruption_check=1 devres.log=1 debug_objects debugpat acpi.debug_layer=0x00410002 acpi.debug_level=0xffffffff acpi=off apic=debug nolapic irqpoll pci=noacpi slub_debug=FZPU
* cat /proc/interrupts is CPU0 0: 16658 XT-PIC-XT timer 1: 289 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 3: 60 XT-PIC-XT uhci_hcd:usb2, ehci_hcd:usb4 5: 9163 XT-PIC-XT sata_via, HDA Intel 7: 0 XT-PIC-XT uhci_hcd:usb3 8: 2 XT-PIC-XT rtc 10: 1712 XT-PIC-XT b43 11: 131 XT-PIC-XT uhci_hcd:usb1 12: 706 XT-PIC-XT i8042 14: 0 XT-PIC-XT ide0 15: 0 XT-PIC-XT ide1 NMI: 0 Non-maskable interrupts LOC: 0 Local timer interrupts RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts SPU: 0 Spurious interrupts ERR: 0 MIS: 0
* lspci -d 14e4:4312 -x 02:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 02) 00: e4 14 12 43 06 01 10 00 02 00 80 02 08 00 00 00 10: 04 c0 ff fd 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 71 13 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00
* xset dpms force standby * wake up * dmesg is virtually the same as before, complaining about nobody handling irq 10 and disabling it. * /proc/interrupts now is 0: 80987 XT-PIC-XT timer 1: 1027 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 3: 60 XT-PIC-XT uhci_hcd:usb2, ehci_hcd:usb4 5: 10400 XT-PIC-XT sata_via, HDA Intel 7: 0 XT-PIC-XT uhci_hcd:usb3 8: 2 XT-PIC-XT rtc 10: 200000 XT-PIC-XT b43 11: 131 XT-PIC-XT uhci_hcd:usb1 12: 3059 XT-PIC-XT i8042 14: 0 XT-PIC-XT ide0 15: 0 XT-PIC-XT ide1 NMI: 0 Non-maskable interrupts LOC: 0 Local timer interrupts RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts SPU: 0 Spurious interrupts ERR: 0 MIS: 0
* Now check this out - the output of lspci -d 14e4:4312 -x 02:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev ff) 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
(I double checked this)
huh?
--yuval [unhandled content-type:application/pgp-signature] | |