Messages in this thread | | | Subject | Re: p4-clockmod not working in 2.6.16 | From | Sasa Ostrouska <> | Date | Tue, 21 Mar 2006 22:57:10 +0100 |
| |
On Tue, 2006-03-21 at 16:01 -0500, Dave Jones wrote: > On Tue, Mar 21, 2006 at 09:55:28PM +0100, Sasa Ostrouska wrote: > > Hello people, > > > > I would like to advise you that in kernel 2.6.16 the > > p4-clockmod module cant recognise my P4 cpu anymore. > > > > This worked perfectly in kernel 2.6.15. I get the following > > error when I modprobe it: > > > > root@rc-vaio:/home/sasa# modprobe msr && modprobe cpuid && modprobe > > p4_clockmod && modprobe speedstep-lib && modprobe microcode && modprobe > > hwmon > > FATAL: Error inserting p4_clockmod > > (/lib/modules/2.6.16/kernel/arch/i386/kernel/cpu/cpufreq/p4-clockmod.ko): No such device > > > > Can somebody explain what happened or how can I set it up ? > > Can you send /proc/cpuinfo and dmesg output please ? > The only thing that recently changed in p4-clockmod is addition > of an errata workaround that disables freqs <2GHz on certain CPUs. > > If the max freq is <2GHz this would disable it completely. > > Dave >
Hi Dave, here it is, this is on a Sony Vaio PCG-GRT816S laptop:
root@rc-vaio:/home/sasa# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Pentium(R) 4 CPU 2.80GHz stepping : 9 cpu MHz : 2807.083 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr bogomips : 5617.52
============================================================================
root@rc-vaio:/home/sasa# dmesg CPU 2.80GHz stepping 09 Checking 'hlt' instruction... OK. ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=16 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... failed. ...trying to set up timer as Virtual Wire IRQ... works. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd996, last bus=1 PCI: Using configuration type 1 ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Uncovering SIS963 that hid as a SIS503 (compatible=1) Enabling SiS 96x SMBus. Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: Embedded Controller [EC0] (gpe 21) interrupt mode. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:04: ioport range 0x8000-0x808f could not be reserved pnp: 00:04: ioport range 0x8090-0x80ff has been reserved pnp: 00:04: ioport range 0x8100-0x811f has been reserved pnp: 00:04: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:04: ioport range 0xfe00-0xfe00 has been reserved PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:01:00.0 PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: d5000000-d5ffffff PREFETCH window: e0000000-efffffff PCI: Bus 2, cardbus bridge: 0000:00:0a.0 IO window: 00002400-000024ff IO window: 00002800-000028ff PREFETCH window: 50000000-51ffffff MEM window: 52000000-53ffffff PCI: Bus 6, cardbus bridge: 0000:00:0a.1 IO window: 00002c00-00002cff IO window: 00003000-000030ff PREFETCH window: 54000000-55ffffff MEM window: 56000000-57ffffff PCI: Enabling device 0000:00:0a.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16 PCI: Enabling device 0000:00:0a.1 (0000 -> 0003) ACPI: PCI Interrupt 0000:00:0a.1[A] -> GSI 17 (level, low) -> IRQ 16 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1142855513.672:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered vesafb: framebuffer at 0xe0000000, mapped to 0xf0880000, using 3750k, total 65536k vesafb: mode is 800x600x32, linelength=3200, pages=1 vesafb: protected mode interface info at c000:f770 vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Battery Slot [BAT2] (battery absent) PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A PCI: Enabling device 0000:00:02.6 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 17 ACPI: PCI interrupt for device 0000:00:02.6 disabled Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SIS5513: IDE controller at PCI slot 0000:00:02.5 SIS5513: chipset revision 0 SIS5513: not 100% native mode: will probe irqs later SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: IC25N080ATMR04-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: PIONEER DVD-RW DVR-K12D, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 156301488 sectors (80026 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 mice: PS/2 mouse device common for all mice MC: drivers/edac/edac_mc.c version edac_mc Ver: 2.0.0 Mar 20 2006 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered ip_conntrack version 2.4 (8175 buckets, 65400 max) - 172 bytes per conntrack input: AT Translated Set 2 keyboard as /class/input/input0 TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI wakeup devices: PWRB COMA EC0 USB0 USB1 USB2 USB3 ACM AUD LAN CB0 CB1 ACPI: (supports S0 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found ReiserFS: hda1: found reiserfs format "3.6" with standard journal ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 148k freed Adding 1839376k swap on /dev/hda3. Priority:-1 extents:1 across:1839376k Linux agpgart interface v0.101 (c) Dave Jones input: PS/2 Generic Mouse as /class/input/input1 ReiserFS: hda2: found reiserfs format "3.6" with standard journal ReiserFS: hda2: using ordered data mode ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda2: checking transaction log (hda2) ReiserFS: hda2: Using r5 hash to sort names ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16 Yenta: CardBus bridge found at 0000:00:0a.0 [104d:814e] Yenta: ISA IRQ mask 0x04b8, PCI irq 16 Socket status: 30000006 ACPI: PCI Interrupt 0000:00:0a.1[A] -> GSI 17 (level, low) -> IRQ 16 Yenta: CardBus bridge found at 0000:00:0a.1 [104d:814e] Yenta: ISA IRQ mask 0x04b8, PCI irq 16 Socket status: 30000006 nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8174 Tue Nov 22 17:48:37 PST 2005 sis900.c: v1.08.09 Sep. 19 2005 ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1. 0000:00:04.0: Using transceiver found at address 1 as default eth0: SiS 900 PCI Fast Ethernet at 0x2000, IRQ 19, 08:00:46:b4:10:b5. usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Enabling device 0000:00:03.3 (0000 -> 0002) ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 20 ehci_hcd 0000:00:03.3: EHCI Host Controller PCI: cache line size of 128 is not supported by device 0000:00:03.3 ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:03.3: irq 20, io mem 0xd4003000 ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 21 ohci_hcd 0000:00:03.0: OHCI Host Controller ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:03.0: irq 21, io mem 0xd4000000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 22 ohci_hcd 0000:00:03.1: OHCI Host Controller ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:03.1: irq 22, io mem 0xd4001000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PCI: Enabling device 0000:00:03.2 (0010 -> 0012) ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 23 ohci_hcd 0000:00:03.2: OHCI Host Controller ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:03.2: irq 23, io mem 0xd4002000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 3-2: new low speed USB device using ohci_hcd and address 2 usb 3-2: configuration #1 chosen from 1 choice usb 4-2: new full speed USB device using ohci_hcd and address 2 ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 17 eth0: Media Link On 100mbps full-duplex usb 4-2: configuration #1 chosen from 1 choice intel8x0_measure_ac97_clock: measured 50479 usecs intel8x0: clocking to 48000 SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev input: Logitech USB Receiver as /class/input/input2 input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:03.1-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver i2c-sis96x version 1.0.0 sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100 agpgart: Detected SiS 648 chipset agpgart: AGP aperture is 64M @ 0xd0000000 Vendor: Sony Model: MSC-U03 Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete sd 0:0:0:0: Attached scsi removable disk sda Real Time Clock Driver v1.12ac input: PC Speaker as /class/input/input3 parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] USB Universal Host Controller Interface driver v2.3 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present lp0: using parport0 (interrupt-driven). agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: SiS delay workaround: giving bridge time to recover. agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: SiS delay workaround: giving bridge time to recover. agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=150802800, high=8, low=16585072, sector=150802800 ide: failed opcode was: unknown end_request: I/O error, dev hda, sector 150802800 ReiserFS: hda2: warning: vs-13070: reiserfs_read_locked_inode: i/o failure occurred trying to find stat data of [5932063 5932077 0x0 SD] process `dig' is using obsolete setsockopt SO_BSDCOMPAT agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: SiS delay workaround: giving bridge time to recover. agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: SiS delay workaround: giving bridge time to recover. agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode CPU0: Temperature above threshold CPU0: Running in modulated clock mode root@rc-vaio:/home/sasa#
Thanks, if you need something else please just let me know. Best Regards Sasa Ostrouska
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |