Messages in this thread | | | Date | Sun, 12 Mar 2006 12:04:14 +0100 (CET) | From | Krzysztof Oledzki <> | Subject | Re: More than 8 CPUs detected and CONFIG_X86_PC cannot handle it on 2.6.16-rc6 |
| |
On Sat, 11 Mar 2006, Andrew Morton wrote:
> Krzysztof Oledzki <olel@ans.pl> wrote: >> >> After upgrading to 2.6.16-rc6 I noticed this strange message: >> >> More than 8 CPUs detected and CONFIG_X86_PC cannot handle it. >> Use CONFIG_X86_GENERICARCH or CONFIG_X86_BIGSMP. >> >> This is a Dell PowerEdge SC1425 with two P4 Xeons with HT enabled (so with >> totoal of 4 logical CPUs). > > Please send full dmesg output for the failing kernel, thanks. Attached.
> Which is the most-recently-tested kernel which behaved correctly? 2.6.15.6
Best regards,
Krzysztof OlędzkiLinux version 2.6.16-rc6 (root@fw2) (gcc version 3.4.5) #1 SMP PREEMPT Sun Mar 12 02:43:26 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 0000000000100000 - 000000007ffc0000 (usable) BIOS-e820: 000000007ffc0000 - 000000007ffcfc00 (ACPI data) BIOS-e820: 000000007ffcfc00 - 000000007ffff000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec90000 (reserved) BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 2047MB LOWMEM available. found SMP MP-table at 000fe710 On node 0 totalpages: 524224 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 520128 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:0 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000fd650 ACPI: RSDT (v001 DELL PESC1425 0x00000001 MSFT 0x0100000a) @ 0x000fd664 ACPI: FADT (v001 DELL PESC1425 0x00000001 MSFT 0x0100000a) @ 0x000fd6b0 ACPI: MADT (v001 DELL PESC1425 0x00000001 MSFT 0x0100000a) @ 0x000fd724 ACPI: SPCR (v001 DELL PESC1425 0x00000001 MSFT 0x0100000a) @ 0x000fd7c0 ACPI: HPET (v001 DELL PESC1425 0x00000001 MSFT 0x0100000a) @ 0x000fd810 ACPI: MCFG (v001 DELL PESC1425 0x00000001 MSFT 0x0100000a) @ 0x000fd848 ACPI: DSDT (v001 DELL PESC1425 0x00000001 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled) Processor #6 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled) Processor #7 15:4 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[32]) IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 32-55 ACPI: IOAPIC (id[0x0a] address[0xfec80800] gsi_base[64]) IOAPIC[2]: apic_id 10, version 32, address 0xfec80800, GSI 64-87 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 3 I/O APICs ACPI: HPET id: 0xffffffff base: 0xfed00000 More than 8 CPUs detected and CONFIG_X86_PC cannot handle it. Use CONFIG_X86_GENERICARCH or CONFIG_X86_BIGSMP. Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 80000000 (gap: 7ffff000:60001000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux-2.6.16r6 ro root=900 rootflags=data=journal ip_conntrack.hashsize=131072 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) mapped IOAPIC to ffffb000 (fec80000) mapped IOAPIC to ffffa000 (fec80800) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Console: colour VGA+ 80x30 Dentry cache hash table entries: 524288 (order: 9, 2097152 bytes) Inode-cache hash table entries: 262144 (order: 8, 1048576 bytes) Memory: 2072088k/2096896k available (2967k kernel code, 24404k reserved, 1041k data, 216k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Using HPET for base-timer Using HPET for gettimeofday Detected 3200.687 MHz processor. Using hpet for high-res timesource Calibrating delay using timer specific routine.. 6404.87 BogoMIPS (lpj=3202439) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 20100000 00000000 00000180 0000641d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available CPU0: Thermal monitoring enabled Checking 'hlt' instruction... OK. CPU0: Intel(R) Xeon(TM) CPU 3.20GHz stepping 03 Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 6400.28 BogoMIPS (lpj=3200140) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 20100000 00000000 00000180 0000641d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (24) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Xeon(TM) CPU 3.20GHz stepping 03 Booting processor 2/6 eip 3000 Initializing CPU#2 Calibrating delay using timer specific routine.. 6400.31 BogoMIPS (lpj=3200157) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 3 CPU: After all inits, caps: bfebfbff 20100000 00000000 00000180 0000641d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: Intel P4/Xeon Extended MCE MSRs (24) available CPU2: Thermal monitoring enabled CPU2: Intel(R) Xeon(TM) CPU 3.20GHz stepping 03 Booting processor 3/7 eip 3000 Initializing CPU#3 Calibrating delay using timer specific routine.. 6400.32 BogoMIPS (lpj=3200161) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 3 CPU: After all inits, caps: bfebfbff 20100000 00000000 00000180 0000641d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: Intel P4/Xeon Extended MCE MSRs (24) available CPU3: Thermal monitoring enabled CPU3: Intel(R) Xeon(TM) CPU 3.20GHz stepping 03 Total of 4 processors activated (25605.79 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 4 CPUs: passed. Brought up 4 CPUs migration_cost=1000,1000 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfc3de, last bus=4 PCI: Using MMCONFIG ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: PXH quirk detected, disabling MSI for SHPC device PCI: PXH quirk detected, disabling MSI for SHPC device Boot video device is 0000:04:0d.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PALO._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PALO.PXHB._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PALO.PXHA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PICH._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) pnp: 00:08: ioport range 0x800-0x87f could not be reserved pnp: 00:08: ioport range 0x880-0x8bf has been reserved pnp: 00:08: ioport range 0x8c0-0x8df has been reserved pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved pnp: 00:08: ioport range 0xc00-0xc0f has been reserved pnp: 00:08: ioport range 0xc10-0xc1f has been reserved pnp: 00:08: ioport range 0xca0-0xcaf has been reserved pnp: 00:08: ioport range 0xc20-0xc3f has been reserved PCI: Bridge: 0000:01:00.0 IO window: e000-efff MEM window: fe900000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:01:00.2 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:02.0 IO window: e000-efff MEM window: fe700000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: d000-dfff MEM window: fe500000-fe6fffff PREFETCH window: f0000000-f7ffffff ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:01:00.0 to 64 PCI: Setting latency timer of device 0000:01:00.2 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 Machine check exception polling timer started. IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com> audit: initializing netlink socket (disabled) audit(1142131816.949:1): initialized Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered Intel E7520/7320/7525 detected.<6>ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:02.0 to 64 Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie01] ACPI: Power Button (FF) [PWRF] ACPI: Video Device [EVGA] (multi-head: no rom: yes post: no) Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy ipmi message handler version 38.0 ipmi device interface IPMI System Interface driver. ipmi_si: Found SMBIOS-specified state machine at I/O address 0xca8, slave address 0x20 IPMI kcs interface initialized IPMI Watchdog: driver initialized Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot. IPMI poweroff: Found a chassis style poweroff function PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A floppy0: no floppy controllers found loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 6.3.9-k4-NAPI Copyright (c) 1999-2005 Intel Corporation. ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 32 (level, low) -> IRQ 177 e1000: 0000:02:04.0: e1000_probe: (PCI:66MHz:32-bit) 00:14:22:b0:cb:52 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 20 (level, low) -> IRQ 185 e1000: 0000:04:03.0: e1000_probe: (PCI:33MHz:32-bit) 00:14:22:b0:cb:53 e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 193 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... hda: HL-DT-ST DVD-ROM GDR-8084N, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 24X DVD-ROM drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. ata_piix 0000:00:1f.2: version 1.05 ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xCCB8 ctl 0xCCB2 bmdma 0xCC80 irq 193 ata2: SATA max UDMA/133 cmd 0xCCA0 ctl 0xCC9A bmdma 0xCC88 irq 193 ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:207f ata1: dev 0 ATA-7, max UDMA/133, 156250000 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : ata_piix ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:207f ata2: dev 0 ATA-7, max UDMA/133, 156250000 sectors: LBA48 ata2: dev 0 configured for UDMA/133 scsi1 : ata_piix Vendor: ATA Model: WDC WD800JD-75MS Rev: 10.0 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: WDC WD800JD-75MS Rev: 10.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 > sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 156250000 512-byte hdwr sectors (80000 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 156250000 512-byte hdwr sectors (80000 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 > sd 1:0:0:0: Attached scsi disk sdb sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 201 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: irq 201, io mem 0xfeb00000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 169, io base 0x0000cce0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 209 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 209, io base 0x0000ccc0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 input: PC Speaker as /class/input/input1 md: raid1 personality registered for level 1 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 dcdbas: Dell Systems Management Base Driver (version 5.6.0-2) GACT probability on Mirror/redirect action on Simple TC action Loaded netem: version 1.2 u32 classifier Perfomance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_conntrack version 2.4 (131072 buckets, 1048576 max) - 232 bytes per conntrack ctnetlink v0.90: registering with nfnetlink. ip_conntrack_pptp version 3.1 loaded ip_nat_pptp version 3.0 loaded ip_tables: (C) 2000-2006 Netfilter Core Team ipt_time loading ipt_random match loaded ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/ IPP2P v0.8.1_rc1 loading ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller IPVS: Registered protocols (TCP, UDP) IPVS: Connection hash table configured (size=65536, memory=512Kbytes) IPVS: ipvs loaded. IPVS: [rr] scheduler registered. IPVS: [wrr] scheduler registered. IPVS: [lc] scheduler registered. IPVS: [wlc] scheduler registered. IPVS: [lblc] scheduler registered. IPVS: [lblcr] scheduler registered. IPVS: [dh] scheduler registered. IPVS: [sh] scheduler registered. IPVS: [sed] scheduler registered. IPVS: [nq] scheduler registered. TCP bic registered TCP cubic registered TCP westwood registered TCP highspeed registered TCP hybla registered TCP htcp registered TCP vegas registered TCP scalable registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 NET: Registered protocol family 15 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available Using IPI No-Shortcut mode ACPI wakeup devices: PCI0 PALO PXH PXHB PXHA PICH ACPI: (supports S0 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 2 devices found md: Autodetecting RAID arrays. input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2 md: autorun ... md: considering sdb9 ... md: adding sdb9 ... md: sdb8 has different UUID to sdb9 md: sdb7 has different UUID to sdb9 md: sdb6 has different UUID to sdb9 md: sdb5 has different UUID to sdb9 md: sdb3 has different UUID to sdb9 md: sdb2 has different UUID to sdb9 md: adding sda9 ... md: sda8 has different UUID to sdb9 md: sda7 has different UUID to sdb9 md: sda6 has different UUID to sdb9 md: sda5 has different UUID to sdb9 md: sda3 has different UUID to sdb9 md: sda2 has different UUID to sdb9 md: created md5 md: bind<sda9> md: bind<sdb9> md: running: <sdb9><sda9> raid1: raid set md5 active with 2 out of 2 mirrors md: considering sdb8 ... md: adding sdb8 ... md: sdb7 has different UUID to sdb8 md: sdb6 has different UUID to sdb8 md: sdb5 has different UUID to sdb8 md: sdb3 has different UUID to sdb8 md: sdb2 has different UUID to sdb8 md: adding sda8 ... md: sda7 has different UUID to sdb8 md: sda6 has different UUID to sdb8 md: sda5 has different UUID to sdb8 md: sda3 has different UUID to sdb8 md: sda2 has different UUID to sdb8 md: created md4 md: bind<sda8> md: bind<sdb8> md: running: <sdb8><sda8> raid1: raid set md4 active with 2 out of 2 mirrors md: considering sdb7 ... md: adding sdb7 ... md: sdb6 has different UUID to sdb7 md: sdb5 has different UUID to sdb7 md: sdb3 has different UUID to sdb7 md: sdb2 has different UUID to sdb7 md: adding sda7 ... md: sda6 has different UUID to sdb7 md: sda5 has different UUID to sdb7 md: sda3 has different UUID to sdb7 md: sda2 has different UUID to sdb7 md: created md3 md: bind<sda7> md: bind<sdb7> md: running: <sdb7><sda7> raid1: raid set md3 active with 2 out of 2 mirrors md: considering sdb6 ... md: adding sdb6 ... md: sdb5 has different UUID to sdb6 md: sdb3 has different UUID to sdb6 md: sdb2 has different UUID to sdb6 md: adding sda6 ... md: sda5 has different UUID to sdb6 md: sda3 has different UUID to sdb6 md: sda2 has different UUID to sdb6 md: created md2 md: bind<sda6> md: bind<sdb6> md: running: <sdb6><sda6> raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdb5 ... md: adding sdb5 ... md: sdb3 has different UUID to sdb5 md: sdb2 has different UUID to sdb5 md: adding sda5 ... md: sda3 has different UUID to sdb5 md: sda2 has different UUID to sdb5 md: created md1 md: bind<sda5> md: bind<sdb5> md: running: <sdb5><sda5> raid1: raid set md1 active with 2 out of 2 mirrors md: considering sdb3 ... md: adding sdb3 ... md: sdb2 has different UUID to sdb3 md: adding sda3 ... md: sda2 has different UUID to sdb3 md: created md15 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid1: raid set md15 active with 2 out of 2 mirrors md: considering sdb2 ... md: adding sdb2 ... md: adding sda2 ... md: created md0 md: bind<sda2> md: bind<sdb2> md: running: <sdb2><sda2> raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with journal data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 216k freed Adding 2007992k swap on /dev/md15. Priority:8192 extents:1 across:2007992k EXT3 FS on md0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on md1, internal journal EXT3-fs: mounted filesystem with journal data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on md2, internal journal EXT3-fs: mounted filesystem with journal data mode.
| |