Messages in this thread | | | Date | Thu, 01 Jul 2004 09:46:09 +0200 | From | Stefano Rivoir <> | Subject | Re: 2.6.7-mm5 |
| |
Andrew Morton wrote:
[...] > What would the next message have been, if it had not hung up?
Here attached, a normal startup with -mm4.
Note that I had this problem also with -mm3, that occasionally hanged both at this step _OR_ after ACPI processor module insertion: in that case the last line shown at startup was:
ACPI: Processor [CPU0] (supports C1, C2, C3, 8 throttling states)
i.e. line #154 in the attached dmesg.
All of the boots I've done with -mm5 (5 or 6), instead, hanged after ide0 (but may be pure coincidence).
Bye
-- Stefano RIVOIR
Linux version 2.6.7-mm4 (root@nbsteu) (gcc version 3.3.4 (Debian 1:3.3.4-2)) #11 Thu Jul 1 08:57:10 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fffa000 (usable) BIOS-e820: 000000001fffa000 - 000000001ffff000 (ACPI data) BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131066 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126970 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 ASUS ) @ 0x000f6410 ACPI: RSDT (v001 ASUS L5C 0x42302e31 MSFT 0x31313031) @ 0x1fffa000 ACPI: FADT (v001 ASUS L5C 0x42302e31 MSFT 0x31313031) @ 0x1fffa0b6 ACPI: BOOT (v001 ASUS L5C 0x42302e31 MSFT 0x31313031) @ 0x1fffa030 ACPI: MADT (v001 ASUS L5C 0x42302e31 MSFT 0x31313031) @ 0x1fffa058 ACPI: DSDT (v001 ASUS L5C 0x00001000 MSFT 0x0100000e) @ 0x00000000 Built 1 zonelists Initializing CPU#0 Kernel command line: auto BOOT_IMAGE=Linux ro root=1602 idebus=66 ide_setup: idebus=66 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2666.739 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x50 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 516340k/524264k available (1327k kernel code, 7188k reserved, 650k data, 96k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 5259.26 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf1670, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: IRQ9 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 11 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) Uncovering SIS963 that hid as a SIS503 (compatible=1) Enabling SiS 96x SMBus. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: Power Resource [FN0] (off) usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:02.3[B] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:0a.1[B] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:0a.2[C] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11 Simple Boot Flag at 0x3a set to 0x80 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 66MHz system bus speed for PIO modes SIS5513: IDE controller at PCI slot 0000:00:02.5 SIS5513: chipset revision 0 SIS5513: not 100% native mode: will probe irqs later SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:pio hda: QSI CD-RW/DVD-ROM SBW-242, ATAPI CD/DVD-ROM drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: IC25N060ATMR04-0, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: max request size: 1024KiB hdc: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 hdc2 hdc3 < hdc5 > i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 Synaptics Touchpad, model: 1 Firmware: 4.6 180 degree mounted touchpad Sensor: 18 new absolute packet format Touchpad has extended capability bits -> four buttons -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 96k freed kjournald starting. Commit interval 5 seconds Adding 248968k swap on /dev/hdc5. Priority:-1 extents:1 EXT3 FS on hdc2, internal journal ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11 sk98lin: Network Device Driver v6.23 (C)Copyright 1999-2004 Marvell(R). ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11 eth0: 3Com Gigabit LOM (3C940) PrefPort:A RlmtMode:Check Link State ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 11 (level, low) -> IRQ 11 intel8x0_measure_ac97_clock: measured 49311 usecs intel8x0: clocking to 48000 ACPI: Battery Slot [BAT0] (battery absent) ACPI: AC Adapter [AC] (on-line) Asus Laptop ACPI Extras version 0.28 Error calling BSTS L5G model detected, supported ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) ACPI: Thermal Zone [THRM] (48 C) Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected SiS 648 chipset agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 64M @ 0xe8000000 [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon R250 Lf [Radeon Mobility 9000 M9] Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 5 (level, low) -> IRQ 5 ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller ohci_hcd 0000:00:03.0: irq 5, pci mem e08f7000 ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 5 (level, low) -> IRQ 5 ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2) ohci_hcd 0000:00:03.1: irq 5, pci mem e08f9000 ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 5 (level, low) -> IRQ 5 ohci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 1.0 Controller (#3) ohci_hcd 0000:00:03.2: irq 5, pci mem e08fb000 ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-2: new low speed USB device using address 2 ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 5 (level, low) -> IRQ 5 ehci_hcd 0000:00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller ehci_hcd 0000:00:03.3: irq 5, pci mem e0914000 ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4 PCI: cache line size of 128 is not supported by device 0000:00:03.3 ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 usb 1-2: USB disconnect, address 2 hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver Linux Kernel Card Services options: [pci] [cardbus] ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:0a.0 [1043:1734] Yenta: ISA IRQ mask 0x0000, PCI irq 11 Socket status: 30000006 ACPI: PCI interrupt 0000:00:0a.1[B] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:0a.1 [1043:1734] Yenta: ISA IRQ mask 0x0040, PCI irq 11 Socket status: 30000006 usb 1-2: new low speed USB device using address 3 drivers/usb/input/hid-core.c: ctrl urb status -32 received input: USB HID v1.00 Mouse [0461:4d03] on usb-0000:00:03.0-2 ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Fan [FAN0] (on) lp: driver loaded but no devices found eth0: network connection up using port A speed: 10 autonegotiation: yes duplex mode: half flowctrl: none irq moderation: disabled scatter-gather: enabled
| |