Messages in this thread | | | Date | Fri, 03 Dec 2004 09:18:53 -0800 | From | "Randy.Dunlap" <> | Subject | Re: sched isolcpus=1 related OOPS in 2.6.9 |
| |
devik wrote: >>only CPU#0 use (I want to use affinity to select CPU#1). >>The OOPS triggers every time when I use isolcpus. >> >>I traced the problem down into sched.c:1928 (find_busiest_group) >>where group->cpu_power was zero (thus division by zero occured). >>In call trace it goes swapper->schedule()->........->find_busiest_group. >>Important registers there: eax=ecx=edx=0, ebx!=0. > > > Well, I have more info. I setup bochs smp emulator and hacked > printk to output into e9 port which is then directed to a file. > Also I turned sched_domains debugging. From the result (below) > is clear that there is bug in isolated domains setup.
You are correct, of course. If "isolcpus" is used, the isolated cpu(s) (in <cpu_isolated_map>) are not init like the remaining cpus are.
I don't know what's intended here... but it's not the divide by 0.
> devik > > <6>BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 0000000000100000 - 0000000002000000 (usable) > <5>32MB LOWMEM available. > <6>found SMP MP-table at 000fd0f0 > <7>On node 0 totalpages: 8192 > <7> DMA zone: 4096 pages, LIFO batch:1 > <7> Normal zone: 4096 pages, LIFO batch:1 > <7> HighMem zone: 0 pages, LIFO batch:1 > <6>DMI not present. > <3>ACPI: Unable to locate RSDP > <6>Intel MultiProcessor Specification v1.4 > <6> Virtual Wire compatibility mode. > <6>OEM ID: BOCHSCPU Product ID: 0.1 APIC at: 0xFEE00000 > Processor #0 6:0 APIC version 17 > Processor #1 6:0 APIC version 17 > <6>I/O APIC #2 Version 17 at 0xFEC00000. > Enabling APIC mode: Flat. Using 1 I/O APICs > <6>Processors: 2 > Built 1 zonelists > Kernel command line: BOOT_IMAGE=linux ro root=301 apic=debug noapic isolcpus=1 > mapped APIC to ffffd000 (fee00000) > mapped IOAPIC to ffffc000 (fec00000) > <6>Initializing CPU#0 > CPU 0 irqstacks, hard=c035b000 soft=c0359000 > PID hash table entries: 256 (order: 8, 4096 bytes) > Detected 2.001 MHz processor. > <6>Using tsc for high-res timesource > Console: colour VGA+ 80x50 > Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) > Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) > <6>Memory: 29372k/32768k available (1511k kernel code, 2960k reserved, 698k data, 168k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > <7>Calibrating delay loop... 8.19 BogoMIPS (lpj=4096) > Mount-cache hash table entries: 512 (order: 0, 4096 bytes) > <7>CPU: After generic identify, caps: 0180a379 00000000 00000000 00000000 > <7>CPU: After vendor identify, caps: 0180a379 00000000 00000000 00000000 > <7>CPU: After all inits, caps: 0180a379 00000000 00000000 00000040 > <6>Enabling fast FPU save and restore... done. > <6>Checking 'hlt' instruction... OK. > CPU0: Intel Pentium III (Coppermine) stepping 03 > per-CPU timeslice cutoff: 81.50 usecs. > task migration cache decay timeout: 1 msecs. > Getting VERSION: 170011 > Getting VERSION: 170011 > Getting ID: 0 > Getting LVT0: 0 > Getting LVT1: 0 > enabled ExtINT on CPU#0 > Booting processor 1/1 eip 2000 > CPU 1 irqstacks, hard=c035c000 soft=c035a000 > <6>Initializing CPU#1 > masked ExtINT on CPU#1 > <7>Calibrating delay loop... 8.19 BogoMIPS (lpj=4096) > <7>CPU: After generic identify, caps: 0180a379 00000000 00000000 00000000 > <7>CPU: After vendor identify, caps: 0180a379 00000000 00000000 00000000 > <7>CPU: After all inits, caps: 0180a379 00000000 00000000 00000040 > CPU1: Intel Pentium III (Coppermine) stepping 03 > <6>Total of 2 processors activated (16.38 BogoMIPS). > Using local APIC timer interrupts. > calibrating APIC timer ... > ..... CPU clock speed is 1.0999 MHz. > ..... host bus clock speed is 1.0999 MHz. > <6>checking TSC synchronization across 2 CPUs: > <6>CPU#0 had 0 usecs TSC skew, fixed it up. > <6>CPU#1 had 0 usecs TSC skew, fixed it up. > Brought up 2 CPUs > <6>Setting up cpu 1 isolated. > <7>CPU0: online > <7> domain 0: span 3 > <7> groups: 1 2 > <7>CPU1: online > <7> domain 0: span 2 > <7>ERROR domain->cpu_power not set > <7> groups: 2 > <1>divide error: 0000 [#1] > SMP > Modules linked in: > CPU: 0 > EIP: 0060:[<c0116fd3>] Not tainted VLI > EFLAGS: 00010046 (2.6.9imq) > EIP is at find_busiest_group+0x2b3/0x310 > eax: 00000000 ebx: c10b2e74 ecx: 00000000 edx: 00000000 > esi: c0360ee8 edi: c0351000 ebp: c10b2e84 esp: c10b2e38 > ds: 007b es: 007b ss: 0068 > Process swapper (pid: 1, threadinfo=c10b2000 task=c10b15a0) > Stack: c10b2e74 00000002 00000002 00004441 08bca3a6 c0351000 00000000 00000001 > 00000080 00000080 00000080 00000000 00000000 c0360edc 00000000 00000002 > 00000040 c1044940 00000001 c10b2eb8 c0117125 c1044940 00000000 c10b2ea8 > Call Trace: > [<c01071ff>] show_stack+0x7f/0xa0 > [<c01073ae>] show_registers+0x15e/0x1c0 > [<c01075c4>] die+0xf4/0x180 > [<c010775b>] do_divide_error+0x10b/0x130 > [<c0106ded>] error_code+0x2d/0x38 > [<c0117125>] load_balance+0x35/0x1a0 > [<c01175fa>] rebalance_tick+0xba/0xd0 > [<c0117732>] scheduler_tick+0x122/0x480 > [<c0124b85>] update_process_times+0x45/0x50 > [<c0111928>] smp_apic_timer_interrupt+0xf8/0x100 > [<c0106d52>] apic_timer_interrupt+0x1a/0x20 > [<c032d03a>] unpack_to_rootfs+0x17a/0x200 > [<c032d0eb>] populate_rootfs+0x2b/0x120 > [<c010058a>] init+0x8a/0x1e0 > [<c0104565>] kernel_thread_helper+0x5/0x10 > Code: 00 0f 4d c2 83 f8 01 89 c1 7e ad 8b 4d d0 85 c9 0f 84 fe fd ff ff 8b 45 e0 01 45 dc 89 c2 8b 4e 08 01 4d d4 c1 e2 07 89 d0 31 d2 <f7> f1 8b 55 cc 85 d2 89 45 e0 75 1c 8b 45 e4 39 45 e0 76 09 89
-- ~Randy - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |