lkml.org 
[lkml]   [2004]   [Oct]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: Linux 2.4.28-rc1
Marcelo Tosatti wrote:
> Hi,
>
> If you have been suddenly CC'ed to this message please search
> your name below - there is something which concerns you.
>
> Replying only to the list, myself and O.Sezer is appreciated.
>
> On Tue, Oct 26, 2004 at 05:02:44PM +0300, O.Sezer wrote:
>
>>There are many lost/forgotten patches posted here on lkml. Since 2.4.28
>>is near and 2.4 is going into "deep maintainance" mode soon, I gathered
>>a short list of some of them.
>
>
> Oh it is hard to bookkeep all of this. I hope people check and resend, but
> they dont do that always.
>
>
>>There, sure, are many more of them, but here it goes.
>
>
> Please send'em all. I really appreciate your efforts.
[...]
>>- Michael Mueller: opti-viper pci-chipset support
>> (have an updated-for-2.4.23+ patch for this)
>> http://marc.theaimsgroup.com/?t=106698970100002&r=1&w=2
>> http://marc.theaimsgroup.com/?l=linux-kernel&m=106698965700864&w=2
>
>
> Should be applied - v2.6 also lacks it AFAICS.

Attached is a one that's supposed to apply cleanly to and work
with 2.4.23+ kernels.

--- 23/arch/i386/kernel/pci-irq.c~
+++ 23/arch/i386/kernel/pci-irq.c
@@ -241,18 +241,56 @@
}

static int pirq_opti_set(struct pci_dev *router, struct pci_dev *dev, int pirq, int irq)
{
write_config_nybble(router, 0xb8, pirq >> 4, irq);
return 1;
}

/*
+ * OPTI Viper-M/N+: Bit field with 3 bits per entry.
+ * Due to the lack of a specification the information about this chipset
+ * was taken from the NetBSD source code.
+ */
+static int pirq_viper_get(struct pci_dev *router, struct pci_dev *dev, int pirq)
+{
+ static const int viper_irq_decode[] = { 0, 5, 9, 10, 11, 12, 14, 15 };
+ u32 irq;
+
+ pci_read_config_dword(router, 0x40, &irq);
+ irq >>= (pirq-1)*3;
+ irq &= 7;
+
+ return viper_irq_decode[irq];
+}
+
+static int pirq_viper_set(struct pci_dev *router, struct pci_dev *dev, int pirq, int irq)
+{
+ static const int viper_irq_map[] = { -1, -1, -1, -1, -1, 1, -1, -1, -1, 2, 3, 4, 5, -1, 6, 7 };
+ int newval = viper_irq_map[irq];
+ u32 val;
+ u32 mask = 7 << (3*(pirq-1));
+#if 0
+ mask |= 0x10000UL << (pirq-1); /* edge triggered */
+#endif
+
+ if ( newval == -1 )
+ return 0;
+
+ pci_read_config_dword(router, 0x40, &val);
+ val &= ~mask;
+ val |= newval << (3*(pirq-1));
+ pci_write_config_dword(router, 0x40, val);
+
+ return 1;
+}
+
+/*
* Cyrix: nibble offset 0x5C
*/
static int pirq_cyrix_get(struct pci_dev *router, struct pci_dev *dev, int pirq)
{
return read_config_nybble(router, 0x5C, (pirq-1)^1);
}

static int pirq_cyrix_set(struct pci_dev *router, struct pci_dev *dev, int pirq, int irq)
{
@@ -707,21 +745,28 @@

static __init int opti_router_probe(struct irq_router *r, struct pci_dev *router, u16 device)
{
switch(device)
{
case PCI_DEVICE_ID_OPTI_82C700:
r->name = "OPTI";
r->get = pirq_opti_get;
r->set = pirq_opti_set;
- return 1;
+ break;
+ case PCI_DEVICE_ID_OPTI_82C558:
+ r->name = "OPTI VIPER";
+ r->get = pirq_viper_get;
+ r->set = pirq_viper_set;
+ break;
+ default:
+ return 0;
}
- return 0;
+ return 1;
}

static __init int ite_router_probe(struct irq_router *r, struct pci_dev *router, u16 device)
{
switch(device)
{
case PCI_DEVICE_ID_ITE_IT8330G_0:
r->name = "ITE";
r->get = pirq_ite_get;
\
 
 \ /
  Last update: 2005-03-22 14:07    [W:0.135 / U:0.600 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site