Messages in this thread | | | From | "Milan Roubal" <> | Subject | Re: 2.6.0test3mm2 - Synaptics touchpad problem | Date | Fri, 15 Aug 2003 14:18:08 +0200 |
| |
Hi, here are logs with debug enabled - working and not working. I think the most interesitng part from the notworking is this:
<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [285] <7>drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [285] <7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [287] <7>drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [287] <7>drivers/input/serio/i8042.c: 93 -> i8042 (command) [290] <7>drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [290] <7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad parity, timeout) [295] <7>drivers/input/serio/i8042.c: 93 -> i8042 (command) [295] <7>drivers/input/serio/i8042.c: ed -> i8042 (parameter) [295] <7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad parity, timeout) [298] <7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [298] <7>drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [298] <7>drivers/input/serio/i8042.c: fe <- i8042 (flush, aux) [300] <7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [300] <7>drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [300] <7>drivers/input/serio/i8042.c: 93 -> i8042 (command) [303] <7>drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [303] <7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad parity, timeout) [308] <7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [308] <7>drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [308] <7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad parity, timeout) [311]
Full logs are attached. Milan Roubal
----- Original Message ----- From: "Paul Nasrat" <pauln@truemesh.com> To: "Milan Roubal" <roubm9am@barbora.ms.mff.cuni.cz> Cc: "Andrew Morton" <akpm@osdl.org>; <linux-kernel@vger.kernel.org> Sent: Friday, August 15, 2003 1:39 PM Subject: Re: 2.6.0test3mm2 - Synaptics touchpad problem
> On Fri, Aug 15, 2003 at 01:00:09PM +0200, Milan Roubal wrote: > > Hi, > > I am using the new drivers for XFree86 and if the touchpad is visible > > Apologies I misread your bug report. Maybe this will be of more help. > > > in dmesg, than it is working in XFree86 too. When it isn't, > > it isn't than listed in /proc/bus/input/devices and is not working in > > XFree86. > > That does seem odd, I haven't noticed this with vanilla 2.6.0test3 > (linux only, but a reboot linux->linux would exhibit that). > > I note on the non synaptics boot you have this instead of the synaptics. > > serio: i8042 AUX3 port at 0x60,0x64 irq 12 > > It may be worth #define DEBUG in i8042.c, to see the differences between > the two boot sequences in more detail. > > You might want to try against 2.6.0-test3, if it works for you > then it might be worth going through the synaptics patches in mm2 one by > one :( > > http://www.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.0-test3/2.6.0-test3-mm2/broken-out/ > > http://w1.894.telia.com/~u89404340/patches/touchpad/2.6.0-test2/v1/Readme.txt > > I'll see if I can replicate this with my laptop this evening. > > Paul > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ [unhandled content-type:application/octet-stream][unhandled content-type:application/octet-stream] | |