lkml.org 
[lkml]   [2003]   [Dec]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectPDC20265 problems with 2.4.23
    Hi,

    I get the following with kernel 2.4.23...

    | [...]
    | PDC20265: IDE controller at PCI slot 00:0c.0
    | PDC20265: chipset revision 2
    | PDC20265: not 100%% native mode: will probe irqs later
    | PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
    | ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:DMA, hdf:pio
    | ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:DMA, hdh:DMA
    | [...]
    | hde: Maxtor 5T040H4, ATA DISK drive
    | hdg: ST3120022A, ATA DISK drive
    | hdh: ST3120022A, ATA DISK drive
    | [...]
    | ide2 at 0xcc00-0xcc07,0xd002 on irq 18
    | ide3 at 0xd400-0xd407,0xd802 on irq 18
    | hde: attached ide-disk driver.
    | hde: host protected area => 1
    | hde: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=79408/16/63
    | hdg: attached ide-disk driver.
    | hdg: host protected area => 1
    | hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63
    | hdh: attached ide-disk driver.
    | hdh: host protected area => 1
    | hdh: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63
    | Partition check:
    | hde: [PTBL] [4982/255/63] hde1
    | hdg: hdg1 hdg2
    | hdh: hdh1
    | [...]
    | hdg: status error: status=0x58 { DriveReady SeekComplete DataRequest }
    |
    | hdg: drive not ready for command
    | hdg: status error: status=0x50 { DriveReady SeekComplete }
    |
    | hdg: no DRQ after issuing MULTWRITE
    | hdg: status timeout: status=0xd0 { Busy }
    |
    | PDC202XX: Secondary channel reset.
    | PDC202XX: Primary channel reset.
    | hdg: no DRQ after issuing WRITE
    | ide3: reset: master: error (0x00?)
    | [...]
    | hde: status error: status=0x51 { DriveReady SeekComplete Error }
    | hde: status error: error=0x04 { DriveStatusError }
    | hde: no DRQ after issuing MULTWRITE
    | hde: status error: status=0x51 { DriveReady SeekComplete Error }
    | hde: status error: error=0x04 { DriveStatusError }
    | hde: no DRQ after issuing MULTWRITE
    | hde: status error: status=0x51 { DriveReady SeekComplete Error }
    | hde: status error: error=0x04 { DriveStatusError }
    | hde: no DRQ after issuing MULTWRITE
    | hde: status error: status=0x51 { DriveReady SeekComplete Error }
    | hde: status error: error=0x04 { DriveStatusError }
    | PDC202XX: Primary channel reset.
    | PDC202XX: Secondary channel reset.
    | hde: no DRQ after issuing WRITE
    | [...]
    | ide2: reset: master: error (0x00?)
    | [...]
    | hdg: lost interrupt
    | hdg: lost interrupt
    | hdg: lost interrupt
    | .
    | .
    | .

    $ grep PDC .config
    CONFIG_BLK_DEV_PDC202XX_OLD=y
    CONFIG_PDC202XX_BURST=y
    # CONFIG_BLK_DEV_PDC202XX_NEW is not set
    # CONFIG_PDC202XX_FORCE is not set
    CONFIG_BLK_DEV_PDC202XX=y
    # CONFIG_BLK_DEV_ATARAID_PDC is not set


    Thanks in advance,
    Gergely
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:59    [W:2.469 / U:0.008 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site