Messages in this thread Patch in this message | ![/](/images/icornerl.gif) | | Date | Mon, 24 Nov 2003 16:36:58 -0800 | From | Mike Fedyk <> | Subject | Re: OOps! was: 2.6.0-test9-mm5 |
| |
On Mon, Nov 24, 2003 at 03:58:07PM -0800, Mike Fedyk wrote: > I just compiled witout preempt and it still gives an oops at the same spot.
Just compiled vanilla 2.6.0-test9 and it doesn't oops.
Let me know if you still want me to hand type that oops.
--- linux-2.6.0-test9/.config 2003-11-24 15:47:54.000000000 -0800 +++ linux-2.6.0-test9-mm5/.config 2003-11-24 15:33:22.000000000 -0800 @@ -29,6 +29,8 @@ CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set # # Loadable module support @@ -84,11 +86,16 @@ CONFIG_X86_POPAD_OK=y CONFIG_X86_ALIGNMENT_16=y CONFIG_X86_INTEL_USERCOPY=y +# CONFIG_X86_4G is not set +# CONFIG_X86_SWITCH_PAGETABLES is not set +# CONFIG_X86_4G_VM_LAYOUT is not set +# CONFIG_X86_UACCESS_INDIRECT is not set +# CONFIG_X86_HIGH_ENTRY is not set CONFIG_HPET_TIMER=y # CONFIG_HPET_EMULATE_RTC is not set CONFIG_SMP=y CONFIG_NR_CPUS=2 -CONFIG_PREEMPT=y +# CONFIG_PREEMPT is not set CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_MCE=y @@ -107,6 +114,7 @@ CONFIG_HIGHPTE=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y +# CONFIG_EFI is not set CONFIG_HAVE_DEC_LOCK=y # @@ -138,6 +146,7 @@ CONFIG_ACPI_PCI=y CONFIG_ACPI_SYSTEM=y # CONFIG_ACPI_RELAXED_AML is not set +CONFIG_X86_PM_TIMER=y # # APM (Advanced Power Management) BIOS Support @@ -165,6 +174,7 @@ CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y +CONFIG_PCI_USE_VECTOR=y CONFIG_PCI_LEGACY_PROC=y CONFIG_PCI_NAMES=y CONFIG_ISA=y @@ -233,6 +243,7 @@ # CONFIG_ISAPNP=y CONFIG_PNPBIOS=y +CONFIG_PNPBIOS_PROC_FS=y # # Block devices @@ -316,7 +327,6 @@ CONFIG_BLK_DEV_OPTI621=y CONFIG_BLK_DEV_RZ1000=y CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDE_TCQ is not set # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set @@ -365,6 +375,7 @@ # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y +CONFIG_MAX_SD_DISKS=256 CONFIG_CHR_DEV_ST=m CONFIG_CHR_DEV_OSST=m CONFIG_BLK_DEV_SR=m @@ -682,6 +693,8 @@ CONFIG_TULIP=m CONFIG_TULIP_MWI=y CONFIG_TULIP_MMIO=y +CONFIG_TULIP_NAPI=y +CONFIG_TULIP_NAPI_HW_MITIGATION=y CONFIG_DE4X5=m CONFIG_WINBOND_840=m CONFIG_DM9102=m @@ -697,6 +710,7 @@ CONFIG_AC3200=m CONFIG_APRICOT=m CONFIG_B44=m +# CONFIG_FORCEDETH is not set CONFIG_CS89x0=m CONFIG_DGRS=m CONFIG_EEPRO100=m @@ -763,6 +777,7 @@ # CONFIG_NET_FC is not set # CONFIG_RCPCI is not set # CONFIG_SHAPER is not set +# CONFIG_NET_POLL_CONTROLLER is not set # # Wan interfaces @@ -1335,7 +1350,6 @@ CONFIG_USB_SERIAL=m CONFIG_USB_SERIAL_GENERIC=y CONFIG_USB_SERIAL_BELKIN=m -# CONFIG_USB_SERIAL_WHITEHEAT is not set CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m CONFIG_USB_SERIAL_EMPEG=m CONFIG_USB_SERIAL_FTDI_SIO=m @@ -1513,12 +1527,11 @@ # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set # CONFIG_EFI_PARTITION is not set -CONFIG_SMB_NLS=y -CONFIG_NLS=y # # Native Language Support # +CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m # CONFIG_NLS_CODEPAGE_737 is not set @@ -1573,9 +1586,12 @@ CONFIG_MAGIC_SYSRQ=y CONFIG_DEBUG_SPINLOCK=y # CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_SPINLINE is not set CONFIG_DEBUG_HIGHMEM=y # CONFIG_DEBUG_INFO is not set +# CONFIG_LOCKMETER is not set CONFIG_DEBUG_SPINLOCK_SLEEP=y +# CONFIG_KGDB is not set CONFIG_FRAME_POINTER=y CONFIG_X86_EXTRA_IRQS=y CONFIG_X86_FIND_SMP_CONFIG=y Linux version 2.6.0-test9 (root@mis-mike-wstn) (gcc version 3.3.2 (Debian)) #1 SMP Mon Nov 24 15:54:45 PST 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e400 (usable) BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000005fffc000 (usable) BIOS-e820: 000000005fffc000 - 000000005ffff000 (ACPI data) BIOS-e820: 000000005ffff000 - 0000000060000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 639MB HIGHMEM available. 896MB LOWMEM available. On node 0 totalpages: 393212 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 225280 pages, LIFO batch:16 HighMem zone: 163836 pages, LIFO batch:16 DMI 2.3 present. Using APIC driver default ACPI: RSDP (v000 ASUS ) @ 0x000f5dc0 ACPI: RSDT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc000 ACPI: FADT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc0b2 ACPI: BOOT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc030 ACPI: MADT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc058 ACPI: DSDT (v001 ASUS A7V8X-X 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1]) ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3]) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Building zonelist for node : 0 Kernel command line: root=/dev/hda1 ro vga=extended nmi_watchdog=2 ide=reverse ide_setup: ide=reverse : Enabled support for IDE inverse scan order. Initializing CPU#0 PID hash table entries: 4096 (order 12: 32768 bytes) Detected 2083.203 MHz processor. Console: colour VGA+ 80x50 spurious 8259A interrupt: IRQ7. Memory: 1552352k/1572848k available (2324k kernel code, 19344k reserved, 890k data, 196k init, 655344k highmem) Calibrating delay loop... 4104.19 BogoMIPS Security Scaffold v1.0.0 initialized Capability LSM initialized Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX CPU0: AMD Athlon(TM) XP 2600+ stepping 01 per-CPU timeslice cutoff: 731.36 usecs. task migration cache decay timeout: 1 msecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Total of 1 processors activated (4104.19 BogoMIPS). ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 1 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2082.0719 MHz. ..... host bus clock speed is 333.0235 MHz. Starting migration thread for cpu 0 CPUS done 2 NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf15e0, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20031002 IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f9bf0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9c20, dseg 0xf0000 PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver SCSI subsystem initialized IOAPIC[0]: Set PCI routing entry (2-17 -> 0xa9 -> IRQ 17 Mode:1 Active:1) 00:00:07[A] -> 2-17 -> IRQ 17 Pin 2-17 already programmed IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb1 -> IRQ 18 Mode:1 Active:1) 00:00:09[A] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb9 -> IRQ 19 Mode:1 Active:1) 00:00:0c[A] -> 2-19 -> IRQ 19 IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc1 -> IRQ 16 Mode:1 Active:1) 00:00:0c[B] -> 2-16 -> IRQ 16 Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1) 00:00:10[A] -> 2-21 -> IRQ 21 Pin 2-21 already programmed sage repeated 2 times IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1) 00:00:11[C] -> 2-22 -> IRQ 22 IOAPIC[0]: Set PCI routing entry (2-23 -> 0xd9 -> IRQ 23 Mode:1 Active:1) 00:00:12[A] -> 2-23 -> IRQ 23 Pin 2-16 already programmed Pin 2-17 already programmed ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' divert: not allocating divert_blk for non-ethernet device lo SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 Machine check exception polling timer started. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Initializing Cryptographic API ACPI: Power Button (FF) [PWRF] ACPI: Processor [CPU0] (supports C1) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found pty: 256 Unix98 ptys configured Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds). Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled 2.6.0-test9-mm5 oopses here.
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255 VP_IDE: chipset revision 6 VP_IDE: not 100%% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 ide0: BM-DMA at 0x8400-0x8407, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8408-0x840f, BIOS settings: hdc:pio, hdd:pio hda: IBM-DPTA-372730, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 SiI680: IDE controller at PCI slot 0000:00:0e.0 SiI680: chipset revision 2 SiI680: BASE CLOCK == 133 SiI680: 100%% native mode on irq 17 ide2: MMIO-DMA at 0xf880a000-0xf880a007, BIOS settings: hde:pio, hdf:pio ide3: MMIO-DMA at 0xf880a008-0xf880a00f, BIOS settings: hdg:pio, hdh:pio hde: Maxtor 6Y160P0, ATA DISK drive ide2 at 0xf880a080-0xf880a087,0xf880a08a on irq 17 hdg: Maxtor 6Y160P0, ATA DISK drive ide3 at 0xf880a0c0-0xf880a0c7,0xf880a0ca on irq 17 PDC20269: IDE controller at PCI slot 0000:00:0c.0 PDC20269: chipset revision 2 PDC20269: 100%% native mode on irq 19 ide4: BM-DMA at 0xb400-0xb407, BIOS settings: hdi:pio, hdj:pio ide5: BM-DMA at 0xb408-0xb40f, BIOS settings: hdk:pio, hdl:pio hdi: Maxtor 6Y160P0, ATA DISK drive ide4 at 0xd800-0xd807,0xd402 on irq 19 hdk: Maxtor 6Y160P0, ATA DISK drive ide5 at 0xd000-0xd007,0xb802 on irq 19 hda: max request size: 128KiB hda: 53464320 sectors (27373 MB) w/1961KiB Cache, CHS=53040/16/63, UDMA(66) hda: hda1 hda2 hde: max request size: 64KiB hde: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133) hde: hde1 hde2 hde3 hdg: max request size: 64KiB hdg: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133) hdg: hdg1 hdg2 hdi: max request size: 1024KiB hdi: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133) hdi: hdi1 hdi3 hdk: max request size: 1024KiB hdk: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133) hdk: hdk1 hdk2 hdk3 mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Translated Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 2948.000 MB/sec 8regs_prefetch: 2844.000 MB/sec 32regs : 1984.000 MB/sec 32regs_prefetch: 1864.000 MB/sec pIII_sse : 1648.000 MB/sec pII_mmx : 5572.000 MB/sec p5_mmx : 7424.000 MB/sec raid5: using function: pIII_sse (1648.000 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.0.0-ioctl (2003-06-04) initialised: dm@uk.sistina.com NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 128Kbytes TCP: Hash tables configured (established 262144 bind 43690) BIOS EDD facility v0.10 2003-Oct-11, 5 devices found Please report your BIOS at http://domsch.com/linux/edd30/results.html md: Autodetecting RAID arrays. md: autorun ... md: considering hdk3 ... md: adding hdk3 ... md: hdk1 has different UUID to hdk3 md: adding hdi3 ... md: adding hde3 ... md: hde1 has different UUID to hdk3 md: created md0 md: bind<hde3> md: bind<hdi3> md: bind<hdk3> md: running: <hdk3><hdi3><hde3> raid5: device hdk3 operational as raid disk 2 raid5: device hdi3 operational as raid disk 1 raid5: device hde3 operational as raid disk 0 raid5: allocated 3148kB for md0 raid5: raid level 5 set md0 active with 3 out of 3 devices, algorithm 0 RAID5 conf printout: --- rd:3 wd:3 fd:0 disk 0, o:1, dev:hde3 disk 1, o:1, dev:hdi3 disk 2, o:1, dev:hdk3 md: considering hdk1 ... md: adding hdk1 ... md: adding hde1 ... md: created md1 md: bind<hde1> md: bind<hdk1> md: running: <hdk1><hde1> raid1: raid set md1 active with 2 out of 2 mirrors md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 196k freed NET: Registered protocol family 1 Adding 364888k swap on /dev/hda2. Priority:1 extents:1 EXT3 FS on hda1, internal journal Real Time Clock Driver v1.12 8139too Fast Ethernet driver 0.9.26 via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html divert: allocating divert_blk for eth0 eth0: VIA VT6102 Rhine-II at 0xf7000000, 00:0c:6e:1f:81:95, IRQ 23. eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1. inserting floppy driver for 2.6.0-test9 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 end_request: I/O error, dev fd0, sector 0 Adding 262136k swap on /usr/swap_file. Priority:2 extents:68 parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) lp0: using parport0 (polling). drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub ehci_hcd 0000:00:10.3: EHCI Host Controller ehci_hcd 0000:00:10.3: irq 21, pci mem f8875000 ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: irq 21, io base 00009400 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: irq 21, io base 00009000 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: irq 21, io base 00008800 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected hub 2-0:1.0: new USB device on port 2, assigned address 2 eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. nfs warning: mount version older than kernel sage repeated 3 times ttyS1: LSR safety check engaged! ttyS1: LSR safety check engaged! process `named' is using obsolete setsockopt SO_BSDCOMPAT sage repeated 5 times drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-2 drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver drivers/usb/core/usb.c: registered new driver usbmouse drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver[unhandled content-type:application/octet-stream] | ![\](/images/icornerr.gif) |