lkml.org 
[lkml]   [2024]   [May]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next v9 2/3] net: gro: move L3 flush checks to tcp_gro_receive and udp_gro_receive_segment
Richard Gobert wrote:
> {inet,ipv6}_gro_receive functions perform flush checks (ttl, flags,
> iph->id, ...) against all packets in a loop. These flush checks are used in
> all merging UDP and TCP flows.
>
> These checks need to be done only once and only against the found p skb,
> since they only affect flush and not same_flow.
>
> This patch leverages correct network header offsets from the cb for both
> outer and inner network headers - allowing these checks to be done only
> once, in tcp_gro_receive and udp_gro_receive_segment. As a result,
> NAPI_GRO_CB(p)->flush is not used at all. In addition, flush_id checks are
> more declarative and contained in inet_gro_flush, thus removing the need
> for flush_id in napi_gro_cb.
>
> This results in less parsing code for non-loop flush tests for TCP and UDP
> flows.
>
> To make sure results are not within noise range - I've made netfilter drop
> all TCP packets, and measured CPU performance in GRO (in this case GRO is
> responsible for about 50% of the CPU utilization).
>
> perf top while replaying 64 parallel IP/TCP streams merging in GRO:
> (gro_receive_network_flush is compiled inline to tcp_gro_receive)
> net-next:
> 6.94% [kernel] [k] inet_gro_receive
> 3.02% [kernel] [k] tcp_gro_receive
>
> patch applied:
> 4.27% [kernel] [k] tcp_gro_receive
> 4.22% [kernel] [k] inet_gro_receive
>
> perf top while replaying 64 parallel IP/IP/TCP streams merging in GRO (same
> results for any encapsulation, in this case inet_gro_receive is top
> offender in net-next)
> net-next:
> 10.09% [kernel] [k] inet_gro_receive
> 2.08% [kernel] [k] tcp_gro_receive
>
> patch applied:
> 6.97% [kernel] [k] inet_gro_receive
> 3.68% [kernel] [k] tcp_gro_receive
>
> Signed-off-by: Richard Gobert <richardbgobert@gmail.com>

> +static inline int inet_gro_flush(const struct iphdr *iph, const struct iphdr *iph2,
> + struct sk_buff *p, bool outer)
> +{
> + const u32 id = ntohl(*(__be32 *)&iph->id);
> + const u32 id2 = ntohl(*(__be32 *)&iph2->id);
> + const u16 ipid_offset = (id >> 16) - (id2 >> 16);
> + const u16 count = NAPI_GRO_CB(p)->count;
> + const u32 df = id & IP_DF;
> + int flush;
> +
> + /* All fields must match except length and checksum. */
> + flush = (iph->ttl ^ iph2->ttl) | (iph->tos ^ iph2->tos) | (df ^ (id2 & IP_DF));
> +
> + if (outer && df)
> + return flush;

if (flush)
return 1;

To be able to avoid the two flush | below?
Or to avoid adding a branch

if (flush | (outer && df))
return 1;

> +
> + /* When we receive our second frame we can make a decision on if we
> + * continue this flow as an atomic flow with a fixed ID or if we use
> + * an incrementing ID.
> + */
> + if (count == 1 && df && !ipid_offset)
> + NAPI_GRO_CB(p)->ip_fixedid = true;
> +
> + if (NAPI_GRO_CB(p)->ip_fixedid && df)
> + return flush | ipid_offset;
> +
> + return flush | (ipid_offset ^ count);

And then simply

if (NAPI_GRO_CB(p)->ip_fixedid)
return ipid_offset;
else
return ipid_offset ^ count;

Since NAPI_GRO_CB(p)->ip_fixedid is only set if DF is set on the first
two segments, and df ^ id2 & IP_DF is tested above, no need to test
that again.

> +}

\
 
 \ /
  Last update: 2024-05-09 16:25    [W:0.094 / U:0.660 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site