lkml.org 
[lkml]   [2024]   [May]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] media: i2c: Fix imx412 exposure control
Hi Gjorgji !

On Wed, May 08, 2024 at 07:02:37PM GMT, Gjorgji Rosikopulos (Consultant) wrote:
> Hi Bryan, Jacopo,
>
> On 5/8/2024 3:43 PM, Jacopo Mondi wrote:
> > Hi Bryan
> >
> > On Wed, May 08, 2024 at 01:30:31PM GMT, Bryan O'Donoghue wrote:
> >> On 08/05/2024 09:02, Jacopo Mondi wrote:
> >>> Hi Bryan
> >>>
> >>> On Mon, May 06, 2024 at 11:38:26PM GMT, Bryan O'Donoghue wrote:
> >>>> Currently we have the following algorithm to calculate what value should be
> >>>> written to the exposure control of imx412.
> >>>>
> >>>> lpfr = imx412->vblank + imx412->cur_mode->height;
> >>>> shutter = lpfr - exposure;
> >>>>
> >>>> The 'shutter' value is given to IMX412_REG_EXPOSURE_CIT however, the above
> >>>> algorithm will result in the value given to IMX412_REG_EXPOSURE_CIT
> >>>> decreasing as the requested exposure value from user-space goes up.
> >>>>
> >>>> e.g.
> >>>> [ 2255.713989] imx412 20-001a: Received exp 1608, analog gain 0
> >>>> [ 2255.714002] imx412 20-001a: Set exp 1608, analog gain 0, shutter 1938, lpfr 3546
> >>>> [ 2256.302770] imx412 20-001a: Received exp 2586, analog gain 100
> >>>> [ 2256.302800] imx412 20-001a: Set exp 2586, analog gain 100, shutter 960, lpfr 3546
> >>>> [ 2256.753755] imx412 20-001a: Received exp 3524, analog gain 110
> >>>> [ 2256.753772] imx412 20-001a: Set exp 3524, analog gain 110, shutter 22, lpfr 3546
> >>>>
> >>>> This behaviour results in the image having less exposure as the requested
> >>>> exposure value from user-space increases.
> >>>>
> >>>> Other sensor drivers such as ov5675, imx218, hid556 and others take the
> >>>> requested exposure value and directly.
> >>>
> >>> has the phrase been truncated or is it me reading it wrong ?
> >>
> >> Sod's law says no matter how many times you send yourself a patch before
> >> sending it to LKML you'll find a typo ~ 2 seconds after reading your patch
> >> on LKML.
> >>
> >
> > Sounds familiar enough
> >
> >>
> >>>> Looking at the range of imx sensors, it appears this particular error has
> >>>> been replicated a number of times but, I haven't so far really drilled into
> >>>> each sensor.
> >>>
> >>> Ouch, what other driver have the same issue ?
> >>
> >> So without data sheet or sensor its hard to say if these are correct or
> >> incorrect, it's the same basic calculation though.
> >>
> >> drivers/media/i2c/imx334.c::imx334_update_exp_gain()
> >>
> >> lpfr = imx334->vblank + imx334->cur_mode->height;
> >> shutter = lpfr - exposure;
> >>
> >> ret = imx334_write_reg(imx334, IMX334_REG_SHUTTER, 3, shutter);
> >>
> >>
> >> drivers/media/i2c/imx335.c::imx335_update_exp_gain()
> >>
> >> lpfr = imx335->vblank + imx335->cur_mode->height;
> >> shutter = lpfr - exposure;
> >>
> >> ret = imx335_write_reg(imx335, IMX334_REG_SHUTTER, 3, shutter);
> >>
> >>
> >> Looking again I'm inclined to believe the imx334/imx335 stuff is probably
> >> correct for those sensors, got copied to imx412/imx577 and misapplied to the
> >> EXPOSURE control in imx412.
> >>
> >
> > Without datasheet/devices it really is hard to tell. Cargo cult at
> > play most probably.
>
> I have explained in previous email. But i will post here as well :-)
>

Thanks, I have probably missed it!

>
> As far as i know this issue is only for this imx412 sensor driver.
> The sensor driver for imx412 was submitted along with imx335 and imx334,
> maybe after all the reworking this was missed.
> imx334 and imx335 are using shutter for setting the exposure from where
> this calculation is taken.

Thanks for clarifying and confirming the other drivers are correct.

>
> However imx412 uses number of lines for exposure.
>
> Reviewed-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
>
> ~Gjorgji
>
> >
> >>
> >>>> - ret = imx412_write_reg(imx412, IMX412_REG_EXPOSURE_CIT, 2, shutter);
> >>>> + ret = imx412_write_reg(imx412, IMX412_REG_EXPOSURE_CIT, 2, exposure);
> >>>
> >>> No datasheet here, can you confirm the IMX412_REG_EXPOSURE_CIT
> >>> register is actually in lines ?
> >>
> >>
> >> Looks like.
> >>
> >> From downstream "coarseIntgTimeAddr"
> >>
> >> imx577_sensor.xml
> >> <coarseIntgTimeAddr>0x0202</coarseIntgTimeAddr>
> >>
> >> imx586/imx586_sensor.cpp
> >> pRegSettingsInfo->regSetting[regCount].registerAddr =
> >> pExposureData->pRegInfo->coarseIntgTimeAddr + 1;
> >>
> >> pRegSettingsInfo->regSetting[regCount].registerData = (lineCount & 0xFF);
> >>
> >>> Apart from that, as the CID_EXPOSURE control limit are correctly
> >>> updated when a new VBLANK is set by taking into account the exposure
> >>> margins, I think writing the control value to the register is the
> >>> right thing to do (if the register is in lines of course)
> >>>
> >>> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
> >>>
> >>> Thanks
> >>> j
> >>>
> >>
> >> If that's good enough I'll fix the typo and apply your RB.
> >
> > Sure
> >
> > Thanks
> > j
> >
> >>
> >> ---
> >> bod
> >>
> >

\
 
 \ /
  Last update: 2024-05-09 10:01    [W:0.067 / U:0.784 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site