lkml.org 
[lkml]   [2020]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/2] net: dsa: lantiq: allow to use all GPHYs on xRX300 and xRX330
Date
Hi,

This looks good.

I haven't checked all the differences between the SoCs, but found some
minor problems in the code for the port configuration.


On 12/3/20 11:03 PM, Aleksander Jan Bajkowski wrote:
> From: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
>
> This patch allows you to use all phs on GRX300 and GRX330. The ARX300 has 3
> and the GRX330 has 4 integrated PHYs connected to different ports compared
> to VRX200.
>
> Port configurations:
>
> xRX200:
> GMAC0: RGMII port
> GMAC1: RGMII port
> GMAC2: GPHY0 (GMII)
> GMAC3: GPHY0 (MII)
> GMAC4: GPHY1 (GMII)
> GMAC5: GPHY1 (MII) or RGMII port
>
> xRX300:
> GMAC0: RGMII port
> GMAC1: GPHY2 (GMII)
> GMAC2: GPHY0 (GMII)
> GMAC3: GPHY0 (MII)
> GMAC4: GPHY1 (GMII)
> GMAC5: GPHY1 (MII) or RGMII port
>
> xRX330:
> GMAC0: RGMII port
> GMAC1: GPHY2 (GMII)
> GMAC2: GPHY0 (GMII)
> GMAC3: GPHY3 (GMII)
GMAC3: GPHY3 (GMII) or GPHY0 (MII)
This can be changed in GSWIP_MII_CFG3 (0xc3)

> GMAC4: GPHY1 (GMII)
> GMAC5: GPHY1 (MII) or RGMII port

You also have to change gswip_mii_mask_cfg() it only supports port 0, 1
and 5, but this SoC can not change port 1 (always connected to internal
GPHY, but it can change port 3 (change between GPHY0/MII/0x0 and
PHY3/GMII/0x1)

>
> Tested on D-Link DWR966 with OpenWRT.
>
> Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
> ---
> drivers/net/dsa/lantiq_gswip.c | 110 +++++++++++++++++++++++++++++++--
> 1 file changed, 104 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/net/dsa/lantiq_gswip.c b/drivers/net/dsa/lantiq_gswip.c
> index 09701c17f3f6..540cf99ad7fe 100644
> --- a/drivers/net/dsa/lantiq_gswip.c
> +++ b/drivers/net/dsa/lantiq_gswip.c
> @@ -222,6 +222,7 @@
> struct gswip_hw_info {
> int max_ports;
> int cpu_port;
> + struct dsa_switch_ops *ops;
> };
>
> struct xway_gphy_match_data {
> @@ -1409,9 +1410,9 @@ static int gswip_port_fdb_dump(struct dsa_switch *ds, int port,
> return 0;
> }
>
> -static void gswip_phylink_validate(struct dsa_switch *ds, int port,
> - unsigned long *supported,
> - struct phylink_link_state *state)
> +static void gswip_xrx200_phylink_validate(struct dsa_switch *ds, int port,
> + unsigned long *supported,
> + struct phylink_link_state *state)
> {
> __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
>
> @@ -1471,7 +1472,70 @@ static void gswip_phylink_validate(struct dsa_switch *ds, int port,
> bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> dev_err(ds->dev, "Unsupported interface '%s' for port %d\n",
> phy_modes(state->interface), port);
> +}
> +
> +static void gswip_xrx300_phylink_validate(struct dsa_switch *ds, int port,
> + unsigned long *supported,
> + struct phylink_link_state *state)
> +{
> + __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +
> + switch (port) {
> + case 0:
> + if (!phy_interface_mode_is_rgmii(state->interface) &&
> + state->interface != PHY_INTERFACE_MODE_MII &

MII is not support on port 0

> + state->interface != PHY_INTERFACE_MODE_REVMII &&

REVMII is not support on port 0

> + state->interface != PHY_INTERFACE_MODE_RMII)

GMII is now supported with 0x9

> + goto unsupported;
> + break;
> + case 1:
> + case 2:
> + case 3:
> + case 4:
> + if (state->interface != PHY_INTERFACE_MODE_INTERNAL)
> + goto unsupported;
> + break;
> + case 5:
> + if (!phy_interface_mode_is_rgmii(state->interface) &&
> + state->interface != PHY_INTERFACE_MODE_INTERNAL)
> + goto unsupported;
port 5 also supports RMIIM with bit 0x3 on xrx300 and xrx330

> + break;
> + default:
> + bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> + dev_err(ds->dev, "Unsupported port: %i\n", port);
> + return;
> + }
> +
> + /* Allow all the expected bits */
> + phylink_set(mask, Autoneg);
> + phylink_set_port_modes(mask);
> + phylink_set(mask, Pause);
> + phylink_set(mask, Asym_Pause);
> +
> + /* With the exclusion of MII and Reverse MII, we support Gigabit,
> + * including Half duplex
> + */
> + if (state->interface != PHY_INTERFACE_MODE_MII &&
> + state->interface != PHY_INTERFACE_MODE_REVMII) {
> + phylink_set(mask, 1000baseT_Full);
> + phylink_set(mask, 1000baseT_Half);
> + }
> +
> + phylink_set(mask, 10baseT_Half);
> + phylink_set(mask, 10baseT_Full);
> + phylink_set(mask, 100baseT_Half);
> + phylink_set(mask, 100baseT_Full);
> +
> + bitmap_and(supported, supported, mask,
> + __ETHTOOL_LINK_MODE_MASK_NBITS);
> + bitmap_and(state->advertising, state->advertising, mask,
> + __ETHTOOL_LINK_MODE_MASK_NBITS);
You can put this block into a common function it is also used the the
xrx200 validate block.

> return;
> +
> +unsupported:
> + bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> + dev_err(ds->dev, "Unsupported interface '%s' for port %d\n",
> + phy_modes(state->interface), port);
> }
>
> static void gswip_phylink_mac_config(struct dsa_switch *ds, int port,
> @@ -1614,7 +1678,7 @@ static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset)
> return ARRAY_SIZE(gswip_rmon_cnt);
> }
>
> -static const struct dsa_switch_ops gswip_switch_ops = {
> +static const struct dsa_switch_ops gswip_xrx200_switch_ops = {
> .get_tag_protocol = gswip_get_tag_protocol,
> .setup = gswip_setup,
> .port_enable = gswip_port_enable,
> @@ -1630,7 +1694,32 @@ static const struct dsa_switch_ops gswip_switch_ops = {
> .port_fdb_add = gswip_port_fdb_add,
> .port_fdb_del = gswip_port_fdb_del,
> .port_fdb_dump = gswip_port_fdb_dump,
> - .phylink_validate = gswip_phylink_validate,
> + .phylink_validate = gswip_xrx200_phylink_validate,
> + .phylink_mac_config = gswip_phylink_mac_config,
> + .phylink_mac_link_down = gswip_phylink_mac_link_down,
> + .phylink_mac_link_up = gswip_phylink_mac_link_up,
> + .get_strings = gswip_get_strings,
> + .get_ethtool_stats = gswip_get_ethtool_stats,
> + .get_sset_count = gswip_get_sset_count,
> +};
> +
> +static const struct dsa_switch_ops gswip_xrx300_switch_ops = {
> + .get_tag_protocol = gswip_get_tag_protocol,
> + .setup = gswip_setup,
> + .port_enable = gswip_port_enable,
> + .port_disable = gswip_port_disable,
> + .port_bridge_join = gswip_port_bridge_join,
> + .port_bridge_leave = gswip_port_bridge_leave,
> + .port_fast_age = gswip_port_fast_age,
> + .port_vlan_filtering = gswip_port_vlan_filtering,
> + .port_vlan_prepare = gswip_port_vlan_prepare,
> + .port_vlan_add = gswip_port_vlan_add,
> + .port_vlan_del = gswip_port_vlan_del,
> + .port_stp_state_set = gswip_port_stp_state_set,
> + .port_fdb_add = gswip_port_fdb_add,
> + .port_fdb_del = gswip_port_fdb_del,
> + .port_fdb_dump = gswip_port_fdb_dump,
> + .phylink_validate = gswip_xrx300_phylink_validate,
> .phylink_mac_config = gswip_phylink_mac_config,
> .phylink_mac_link_down = gswip_phylink_mac_link_down,
> .phylink_mac_link_up = gswip_phylink_mac_link_up,
> @@ -1892,7 +1981,7 @@ static int gswip_probe(struct platform_device *pdev)
> priv->ds->dev = dev;
> priv->ds->num_ports = priv->hw_info->max_ports;
> priv->ds->priv = priv;
> - priv->ds->ops = &gswip_switch_ops;
> + priv->ds->ops = priv->hw_info->ops;
> priv->dev = dev;
> version = gswip_switch_r(priv, GSWIP_VERSION);
>
> @@ -1973,10 +2062,19 @@ static int gswip_remove(struct platform_device *pdev)
> static const struct gswip_hw_info gswip_xrx200 = {
> .max_ports = 7,
> .cpu_port = 6,
> + .ops = &gswip_xrx200_switch_ops,
> +};
> +
> +static const struct gswip_hw_info gswip_xrx300 = {
> + .max_ports = 7,
> + .cpu_port = 6,
> + .ops = &gswip_xrx300_switch_ops,
> };
>
> static const struct of_device_id gswip_of_match[] = {
> { .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 },
> + { .compatible = "lantiq,xrx300-gswip", .data = &gswip_xrx300 },
> + { .compatible = "lantiq,xrx330-gswip", .data = &gswip_xrx300 },
> {},
> };
> MODULE_DEVICE_TABLE(of, gswip_of_match);
>


[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-12-04 01:36    [W:0.060 / U:0.452 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site