lkml.org 
[lkml]   [2024]   [May]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2 2/2] arm64: dts: rockchip: Add Radxa ROCK 3C
From
Hi Chukun,

On 2024-04-28 14:36, Chukun Pan wrote:
> The Radxa ROCK 3C is a development board with the
> Rockchip RK3566 SoC. It has the following features:
>
> - 1/2/4GB LPDDR4
> - 1x HDMI Type A
> - 1x PCIE 2.0 slot
> - 1x FAN connector
> - 3.5mm jack with mic
> - 1GbE RTL8211F Ethernet
> - 1x USB 3.0, 3x USB 2.0
> - 40-pin expansion header
> - MicroSD card/eMMC socket
> - 16MB SPI NOR (gd25lq128d)
> - AP6256 or AIC8800 WiFi/BT
>
> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3566-rock-3c.dts | 750 ++++++++++++++++++
> 2 files changed, 751 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-rock-3c.dts
>

[snip]

> +
> +&i2c0 {
> + status = "okay";
> +
> + vdd_cpu: regulator@1c {
> + compatible = "tcs,tcs4525";
> + reg = <0x1c>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + rk809: pmic@20 {
> + compatible = "rockchip,rk809";
> + reg = <0x20>;

[snip]

> + codec {
> + mic-in-differential;

This should be rockchip,mic-in-differential or removed.

> + };
> + };
> +
> + eeprom: eeprom@50 {
> + compatible = "belling,bl24c16a", "atmel,24c16";
> + reg = <0x50>;
> + pagesize = <16>;
> + };
> +};
> +

[snip]

> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + disable-wp;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> + sd-uhs-sdr50;

Do you have any references to issues related to why sd-uhs-sdr104 is not
used here?

My testing shows that io-domain is getting notified and correctly
configured during boot. And card seem to be working correctly.

[ 2.162780] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)

[ 2.229408] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[ 2.230042] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[ 2.231493] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000
[ 2.232121] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000 done
[ 2.257294] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[ 2.269482] dwmmc_rockchip fe2b0000.mmc: Successfully tuned phase to 254
[ 2.270098] mmc1: new ultra high speed SDR104 SDXC card at address aaaa
[ 2.271533] mmcblk1: mmc1:aaaa SD64G 59.5 GiB
[ 2.277357] mmcblk1: p1

Also when the card is later removed/re-inserted:

[ 80.181598] mmc1: card aaaa removed
[ 83.836785] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[ 83.837611] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[ 83.839263] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[ 83.839952] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[ 83.855358] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 84.153827] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[ 84.154524] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[ 84.156149] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000
[ 84.156838] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000 done
[ 84.183932] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[ 84.202888] dwmmc_rockchip fe2b0000.mmc: Successfully tuned phase to 257
[ 84.203574] mmc1: new ultra high speed SDR104 SDXC card at address aaaa
[ 84.205537] mmcblk1: mmc1:aaaa SD64G 59.5 GiB
[ 84.211434] mmcblk1: p1

sd-uhs-ddr50 should also work based on my testing.

Regards,
Jonas

> + vmmc-supply = <&vcc3v3_sys>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +

[snip]

\
 
 \ /
  Last update: 2024-05-27 18:15    [W:0.157 / U:0.636 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site