lkml.org 
[lkml]   [2024]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 7/7] drivers: iio: imu: Add support for adis1657x family
On Wed, 8 May 2024 17:32:34 +0300
Ramona Gradinariu <ramona.bolboaca13@gmail.com> wrote:

> Hello Jonathan,
>
> Some explanations from my side.
>
> >> @@ -437,6 +467,130 @@ static int adis16475_set_filter(struct adis16475 *st, const u32 filter)
> >> return 0;
> >> }
> >>
> >> +static ssize_t adis16475_get_fifo_enabled(struct device *dev,
> >> + struct device_attribute *attr,
> >> + char *buf)
> >> +{
> >> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
> >> + struct adis16475 *st = iio_priv(indio_dev);
> >> + int ret;
> >> + u16 val;
> >> +
> >> + ret = adis_read_reg_16(&st->adis, ADIS16475_REG_FIFO_CTRL, &val);
> >> + if (ret)
> >> + return ret;
> >> + val = FIELD_GET(ADIS16475_FIFO_EN_MASK, val);
> >> +
> >> + return sysfs_emit(buf, "%d\n", val);
> > As below, might as well put the FIELD_GET() in the sysfs_emit rather than
> > writing the local parameter.
>
> In all instances where I did, I did it to avoid casting. v2 inlines the values and
> the cast is needed to avoid compilation errors.

I'd guess that is because the type in the sysfs_emit isn't the same as FIELD_GET()
returns? That will correspond to the type of the ADIS16475_FIFO_EN_MASK
which is defined as UL I think. So just use %lu here instead and need to cast goes
away.

>
> >
> >> + if (adis->data->burst_max_len)
> >> + burst_max_length = adis->data->burst_max_len;
> >> + else
> >> + burst_max_length = burst_length;
> >> +
> >> + tx = adis->buffer + burst_max_length;
> >> + tx[0] = ADIS_READ_REG(burst_req);
> >> +
> >> + if (burst_req)
> > If !burst_req does the rest of this do anything at all?
> > If so flip the logic as
> > if (!burst_req)
> > return adis16475_push_single_sample(pf);
> >
> > the rest...
> > return spi_sync(adis->spi, &adis->msg);
>
> The update is needed even if burst_req is false. The adis message has to be updated
> based on the burst request value, which is then used either in
> adis16475_push_single_sample or in spi_sync call.

Which update? The content of tx[0]? If so that is non obvious so definitely
need a comment. Perhaps even wrap up the update in a function with a name
that makes it clear it's changing the adis->msg.

adis_update_msg_burst() or something like that.
>
> >
> >
> >> + return spi_sync(adis->spi, &adis->msg);
> >> +
> >> + return adis16475_push_single_sample(pf);
> >> +}
> >> +

Jonathan

\
 
 \ /
  Last update: 2024-05-27 18:24    [W:0.053 / U:1.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site